Turbulent Premixed Flame Modeling Using the Algebraic Flame Surface Wrinkling Model: A Comparative Study between OpenFOAM and Ansys Fluent

Hereafter, we used the Algebraic Flame Surface Wrinkling (AFSW) model to conduct numerical simulations of the Paul Scherrer Institute (PSI) high-pressure, turbulent premixed Bunsen flame experiments. We implemented the AFSW model in OpenFOAM and in Ansys Fluent, and we compared the outcome of both solvers against the experimental results. We also highlight the differences between both solvers. All the simulations were performed using a two-dimensional axisymmetric model with the standard k−ϵ turbulence model with wall functions. Two different fuel/air mixtures were studied, namely, a 100%CH4 volumetric ratio and a 60%CH4+ 40%H2 volumetric ratio. The thermophysical and transport properties of the mixture were calculated as a function of temperature using the library Cantera (open-source suite of tools for problems involving chemical kinetics, thermodynamics, and transport processes), together with the GRI-Mech 3.0 chemical mechanism. It was found that the outcome of the AFSW model implemented in both solvers was in good agreement with the experimental results, quantitatively and qualitatively speaking. Further assessment of the results showed that, as much as the chemistry, the turbulence model and turbulent boundary/initial conditions significantly impact the flame shape and height.

Influence of the growth gradient on surface wrinkling and pattern transition in growing tubular tissues

Growth-induced pattern formations in curved film-substrate structures have attracted extensive attention recently. In most existing literature, the growth tensor is assumed to be homogeneous or piecewise homogeneous. In this paper, we aim at clarifying the influence of a growth gradient on pattern formation and pattern evolution in bilayered tubular tissues under plane-strain deformation. In the framework of finite elasticity, a bifurcation condition is derived for a general material model and a generic growth function. Then we suppose that both layers are composed of neo-Hookean materials. In particular, the growth function is assumed to decay linearly either from the inner surface or from the outer surface. It is found that a gradient in the growth has a weak effect on the critical state, compared with the homogeneous growth type where both layers share the same growth factor. Furthermore, a finite-element model is built to validate the theoretical model and to investigate the post-buckling behaviours. It is found that the associated pattern transition is not controlled by the growth gradient but by the ratio of the shear modulus between two layers. Different morphologies can occur when the modulus ratio is varied. The current analysis could provide useful insight into the influence of a growth gradient on surface instabilities and suggests that a homogeneous growth field may provide a good approximation on interpreting complicated morphological formations in multiple systems.

Biobased Ionic Liquids as Multitalented Materials in Lipidic Drug Implants

Lipidic implants are valuable controlled delivery systems that present good biocompatibility and are useful for long-lasting therapies. However, these promising systems can present inflexible drug release profiles that limit their performance. Thus, finding new materials to overcome this drawback is crucial. Herein, lipidic implants containing caffeine and poorly soluble salicylic acid and rutin were developed. The inclusion of Gelucire® 50/02, sucrose, and two biobased ionic liquids, [Cho][Phe] and [Cho][Glu], were evaluated as a mean to improve the performance of the systems. The formulation procedure, dye content distribution, drug content, drug release, water content, and lipidic erosion of the developed systems were assessed. AFM analysis of the implants containing ILs was also performed. The results demonstrated that neither Gelucire® 50/02 nor sucrose were suitable tools to improve the drug release profile. In contrast, the ILs proved to be promising materials for multiple reasons; not only did they facilitate the formulation and incorporation of the studied drugs into the implants, but they also allowed a more suitable release profile, with [Cho][Glu] allowing a higher drug release due to its ability to increase surface wrinkling. Hence, this study showcases ILs as multitalented materials in lipid-based drug implants.

Influence of Osmotic Pressure on Nanostructures in Thin Films of a Weakly-Segregated Block Copolymer and Its Blends with a Homopolymer

We studied the influence of osmotic pressure on nanostructures in thin films of a symmetric weakly-segregated polystyrene-block-poly (methyl methacrylate), P(S-b-MMA), block copolymer and its mixtures with a polystyrene (PS) homopolymer of various compositions. Thin films were deposited on substrates through surface neutralization. The surface neutralization results from the PS mats, which were oxidized and cross-linked by UV-light exposure. Thus, thermal annealing produced perpendicularly oriented lamellae and perforated layers, depending on the content of added PS chains. Nevertheless, a mixed orientation was obtained from cylinders in thin films, where a high content of PS was blended with the P(S-b-MMA). A combination of UV-light exposure and acetic acid rinsing was used to remove the PMMA block. Interestingly, the treatment of PMMA removal inevitably produced osmotic pressure and consequently resulted in surface wrinkling of perpendicular lamellae. As a result, a hierarchical structure with two periodicities was obtained for wrinkled films with perpendicular lamellae. The formation of surface wrinkling is due to the interplay between UV-light exposure and acetic acid rinsing. UV-light exposure resulted in different mechanical properties between the skin and the inner region of a film. Acetic acid rinsing produced osmotic pressure. It was found that surface wrinkling could be suppressed by reducing film thickness, increasing PS content and using high-molecular-weight P(S-b-MMA) BCPs.

Dynamic Reversible Evolution of Wrinkles on Floating Polymer Films under Magnetic Control

In this paper, we present a simple and versatile method to dynamically and reversibly tailor surface wrinkles on a floating polymer film by combining a magnetic droplet and neodymium magnet. The magnetic force from the attraction of the neodymium magnet to the magnetic droplet is the main reason for surface instabilities of floating polymer films, which can induce radial stress in the radial direction, and further, compressive stress in the circumferential direction. This compressive stress can trigger not only floating film wrinkling but also a wrinkle-fold transition. Surface morphologies on the floating polymer film have been systematically studied, by varying the distance between the magnetic droplet and neodymium magnet, polymer film thickness, and magnetic droplet volume. With the decrease in the distance between a magnetic droplet and a neodymium magnet, the decrease in polymer film thickness, and the increase in the magnetic droplet volume, the wrinkle numbers increase and even a wrinkle-fold transition happens. Additionally, the coupling effect of multiple magnetic droplets on the floating film has also been used to achieve novel surface wrinkle patterns, which greatly widens the applications of surface wrinkling.