Improvement in the Resistance to Wear of Work-Rolls Used in Finishing Stands of the Hot Strip Mills

Work-rolls manufactured through the Indefinite Chill Double Poured (ICDP) method present an exterior work layer manufactured in a martensitic white cast iron alloyed with 4.5 %Ni, 1.7 %Cr, and 0.7 %Nb (wt.%). In its microstructure, there are abundant carbides of the type M3C and MC, which give high resistance to wear, and graphite particles which improve the service behaviour of the rolls against thermal cycling. The core of the rolls is manufactured in grey cast iron of pearlitic matrix and spheroidal graphite. These work-rolls are used in the finishing stands in Hot Strip Mills for rolling slabs proceeding from continuous casting at 1200 °C. Through the application of a Design of Experiments (DoE), an attempt has been made to identify those manufacturing factors which have a significant effect on resistance to wear of these rolls and to find an optimal combination of levels of these factors which allow for improvement in resistance to wear. To increase resistance to wear, it is recommended to situate, simultaneously, the liquidus temperature and the percentage of Si in the respective ranges of 1250–1255 °C and 1.1–1.15 (wt.%). Higher liquidus temperatures favour the presence of the pro-eutectic constituent rather than the eutectic constituent. The outer zone of the work layer, in contact with the metal sheet, which is being rolled, does not show the graphitising effect of Si (0.8–1.15 wt.%). On the contrary, it confirms the hardening effect of the Si in solid solution of the ferrite. The addition of 0.02% of Mg (wt.%) and the inoculation of 6 kg/T of FeB tend to eliminate the graphitising effect of the Si, thus favouring that the undissolved carbon in the austenite is found to form carbides in contrast to the majority formation of graphite.

Stochastic Method to Predict Effects of Roll Grinding Deviations on Sheet Flatness in Cold Rolling

Industrial measurements of the diameter profiles of work-rolls used in cold sheet rolling are applied with a stochastic roll-stack model to better understand how residual error from the roll grinding process affects the rolled sheet flatness quality. Roll diameter measurements taken via a non-contact, optical device on new, warm, and worn work-rolls show that the diameter deviations vary along the roll lengths, across roll samples, and at different operational states, suggesting a multi-dimensional random field problem. Studies are conducted for a 4-high rolling mill with 301 stainless steel sheet to investigate the reliability in achieving target flatness considering the work-roll diameter random field. Also investigated is the sensitivity of the flatness reliability to roll diameter deviations at different locations along the roll lengths, and for the three operational states (newly machined, warm, and worn following several passes). The results lead to several key findings. Foremost, it is shown that an assumption of statistical independence among the residual grinding errors at different roll axis locations is improper. Further, it is demonstrated that, for the measured grinding error correlation patterns, the roll diameter deviations external to the roll/sheet contact region play an important role in contributing to flatness defects within the sheet, and that these influences vary according to the roll operational state (new, warm, worn). The presented stochastic model and applied measurement data thus provide for a new understanding into how roll grinding performance influences dimensional quality in the sheet rolling process.

Stress due to interfacial slip causing sleeve fracture in shrink-fitted work roll

The rolls are classified into two types; one is a single-solid type, and the other is a shrink-fitted construction type consisting of a sleeve and a shaft. The bimetallic work rolls are widely used in the roughing stands of hot rolling stand mills. Regarding a shrink-fitted construction type, the interfacial slip sometimes appears between the shaft and the shrink-fitted sleeve. This interfacial slip can be regarded as the relative displacement between the sleeve and the shaft. In this paper, the stress due to the interfacial slip is studied because the stress may cause the sleeve fracture. It is found that the stress in the shrink-fitted surface is slightly decreased with increasing number of rotations [Formula: see text]. Therefore, the stress obtained by the simulation at [Formula: see text] can be used to estimate the fatigue strength.

Metallurgy of Highly Wear-Resistant Indefinite-Chill Work Roll Materials for Hot Rolling Mills

Indefinite-chill materials are used as shell materials for cast work rolls for surface-critical applications in hot rolling mills. Besides a smooth surface quality, a low sticking tendency and low sensitivity against incidents in the rolling mill, the work rolls need the highest wear resistance possible. The microstructure of the indefinite-chill material consists of various carbides (cementite up to 40 area-%) and up to 5 area-% of graphite embedded in tempered martensite. To increase the wear resistance of this material group, the comparably soft cementite has to be replaced by more wear resistant carbides such as MC, M2C or M6C. This can be achieved by increasing the amount of carbide forming elements such as Nb, V, Mo, W or Cr. Nevertheless it is important to maintain a certain amount of graphite in the microstructure to avoid sticking to the rolled material and to lower the sensitivity against mill incidents. It is well known that high amounts of carbide forming elements limit the graphite precipitation and therefore a sophisticated alloying concept is required for this material type. Not only the effects of matrix elements such as Si, Mn, Ni and Co but also the effects of Cr, Mo, W, Nb and V were studied in an intensive research project. This work gives an insight in the results of the project based on the example of the effects of Si and Cr on the phase amounts and the composition of the cementite phase.

On the Evolution of Temperature and Combined Stress in a Work Roll under Cyclic Thermo-Mechanical Loadings during Hot Strip Rolling and Idling

An accurate prediction of temperature and stress evolution in work rolls is crucial to assess the service life of the work roll. In this paper, a finite element method (FEM) model with a deformable work roll and a meshed, rigid body considering complex thermal boundary conditions over the roll surface is proposed to assess the temperature and the thermal stress in work rolls during hot rolling and subsequent idling. After that, work rolls affected by the combined action of temperature gradient and rolling pressure are investigated by taking account of the hot strip. The accuracy of the proposed model is verified through comparison with the calculation results obtained from the mathematical model. The results show that thermal stress is dominant in the bite region of work rolls during hot rolling. Afterwards, the heat treatment residual stresses which are related to thermal fatigue are simulated and introduced into the work roll as the initial stress to evaluate the redistribution under the thermal cyclic loads during the hot rolling process. Results show that the residual stress significantly changed near the roll surface.