Effect of Holding Time on Populations of Microparticles in Spheroidal Graphite Irons

Non-metallic microparticles in spheroidal graphite irons are a product of the inoculation and the Mg-treatment of the liquid melt. Besides the influence on the mechanical properties of these iron–carbon–silicon alloys, they are also responsible for the nucleation and the morphology of the graphite phase. The present investigation is undertaken to study holding time effects of a (Ba, Ca, Al)–ferrosilicon (called Ba-inoculant) and (Ca, Al)–ferrosilicon (called Ca-inoculant) inoculants on the overall distribution of microparticles. Using the 2D to 3D conversions method, which is typically used for graphite nodules, the non-metallic microparticles’ statistical parameters, such as size distributions and number densities, are quantified. The total number of particles is similar after Mg-treatment and inoculation for Ca-inoculant but not for Ba-inoculated samples, which lose approximately 25 pct of microparticles after 1 minute of holding time. Iron treated with the Ca-inoculant loses about 37 pct of its nodules after 5 minutes, while the Ba-inoculated melts maintain their performance even after 10 minutes. Based on extrapolating the trend of the undercooling, Ba-inoculated samples would reach the uninoculated undercooling values in 48 minutes, while Ca-inoculated samples in only 11 minutes. By evaluating the size distributions of the non-metallic microparticles, the Ostwald ripening hypothesis or particle aggregation can be verified. The results suggest that sulfides are more critical for graphite nucleation since they can be correlated with the graphite number densities. However, due to the small difference in the microparticle population of the uninoculated sample with Ca-inoculated samples, other aspects of the fading mechanism need to be considered, such as transient metastable states, since the central hypothesis of loss of inclusions cannot alone explain the decrease in the nucleation frequency of graphite.

Improvement in the Resistance to Wear of Work-Rolls Used in Finishing Stands of the Hot Strip Mills

Work-rolls manufactured through the Indefinite Chill Double Poured (ICDP) method present an exterior work layer manufactured in a martensitic white cast iron alloyed with 4.5 %Ni, 1.7 %Cr, and 0.7 %Nb (wt.%). In its microstructure, there are abundant carbides of the type M3C and MC, which give high resistance to wear, and graphite particles which improve the service behaviour of the rolls against thermal cycling. The core of the rolls is manufactured in grey cast iron of pearlitic matrix and spheroidal graphite. These work-rolls are used in the finishing stands in Hot Strip Mills for rolling slabs proceeding from continuous casting at 1200 °C. Through the application of a Design of Experiments (DoE), an attempt has been made to identify those manufacturing factors which have a significant effect on resistance to wear of these rolls and to find an optimal combination of levels of these factors which allow for improvement in resistance to wear. To increase resistance to wear, it is recommended to situate, simultaneously, the liquidus temperature and the percentage of Si in the respective ranges of 1250–1255 °C and 1.1–1.15 (wt.%). Higher liquidus temperatures favour the presence of the pro-eutectic constituent rather than the eutectic constituent. The outer zone of the work layer, in contact with the metal sheet, which is being rolled, does not show the graphitising effect of Si (0.8–1.15 wt.%). On the contrary, it confirms the hardening effect of the Si in solid solution of the ferrite. The addition of 0.02% of Mg (wt.%) and the inoculation of 6 kg/T of FeB tend to eliminate the graphitising effect of the Si, thus favouring that the undissolved carbon in the austenite is found to form carbides in contrast to the majority formation of graphite.

Morphology and wear of high chromium and austempered ductile iron balls as grinding media in ball mills

High chromium balls are recognized as better grinding media in terms of wear rates than forged steel balls, which are conventional grinding media in the milling process of iron ore. In this research work, the wear rate of high chromium balls and austempered ductile iron (ADI) balls as crushing media in a ball mill are compared. ADI are prepared by austenitizing the spheroidal graphite (SG) iron balls at 920 °C for one hour, and step austempering heat treatments were given, which includes the first step austenitizing at 300 °C for 15 min, followed by a second step austenitizing at 400 °C for 60 min. The wear rates were estimated when both balls were used separately by maintaining the same machining conditions and when the balls are mixed. The grinding wear conduct of both materials is evaluated for wear loss in wet grinding conditions. The experimental results reveal that the performance of ADI balls is better than high chromium balls when tested separately and mixed. Results also indicate that the wear rates/revolutions will decrease when the operating period increases.

Ultrafine Ductile and Austempered Ductile Irons by Solidification in Ultrasonic Field

In this research, ultrasonic melt treatment (UST) was used to produce a new ultrafine grade of spheroidal graphite cast iron (SG iron) and austempered ductile iron (ADI) alloys. Ultrasonic treatment was numerically simulated and evaluated based on acoustic wave streaming. The simulation results revealed that the streaming of the acoustic waves propagated as a stream jet in the molten SG iron along the centerline of the ultrasonic source (sonotrode) with a maximum speed of 0.7 m/s and gradually decreased to zero at the bottom of the mold. The metallographic analysis of the newly developed SG iron alloy showed an extremely ultrafine graphite structure. The graphite nodules’ diameter ranging between 6 and 9 µm with total nodule count ranging between 900 to more than 2000 nodules per mm2, this nodule count has never been mentioned in the literature for castings of the same diameter, i.e., 40 mm. In addition, fully ferritic matrix was observed in all UST SG irons. Further austempering heat treatments were performed to produce different austempered ductile iron (ADI) grades with different ausferrite morphologies. The dilatometry studies for the developed ADI alloys showed that the time required for the completion of the ausferrite formation in UST alloys was four times shorter than that required for statically solidified SG irons. SEM micrographs for the ADI alloys showed an extremely fine and short ausferrite structure together with small austenite blocks in the matrix. A dual-phase intercritically austempered ductile iron (IADI) alloy was also produced by applying partial austenitization heat treatment in the intercritical temperature range, where austenite + ferrite + graphite phases coexist. In dual-phase IADI alloy, it was established that introducing free ferrite in the matrix would provide additional refinement for the ausferrite.

The Role of Selenium on the Formation of Spheroidal Graphite in Cast Iron

Sulfur, an element that belongs to group 16 (chalcogens) of the periodic table, is an excellent promoter of nucleation substrates for graphite in cast iron. In ductile iron, sulfur favors a higher nodule count, which inhibits the risk of carbides and of microporosity. It is reasonable to expect that other elements from group 16, such as selenium or tellurium, play similar roles in the nucleation of graphite. The objective of this paper was to investigate the effect of selenium on the process of graphite formation. Thermal analysis cups were poured to evaluate the nodule count and size distribution. Some of the cups were not inoculated, while others were inoculated with a Ce-bearing inoculant, or with the Ce inoculant and additions of Se. Cross-shaped castings were also poured to quantify the microporosity regions by tomography. It appears that selenium additions modify the number and size of graphite particles, as well as the volume of microshrinkage. Direct correlations between these three parameters were found. Advanced Extensive Field Emission Gun Scanning Electron Microscope (FEG-SEM) techniques were used to identify the nature of the main nucleation compounds. Selenides, combined with Mg and rare earths, were observed to serve as nuclei for graphite. Their presence was justified by thermodynamics calculations.

Experimental Investigation and Optimization of Electric Discharge Machining Process Parameters Using Grey-Fuzzy-Based Hybrid Techniques

Electrical discharge machining (EDM) has recently been shown to be one of the most successful unconventional machining methods for meeting the requirements of today’s manufacturing sector by producing complicated curved geometries in a broad variety of contemporary engineering materials. The machining efficiency of an EDM process during hexagonal hole formation on pearlitic Spheroidal Graphite (SG) iron 450/12 grade material was examined in this study utilizing peak current (I), pulse-on time (Ton), and inter-electrode gap (IEG) as input parameters. The responses, on the other hand, were the material removal rate (MRR) and overcut. During the experimental trials, the peak current ranged from 32 to 44 A, the pulse-on duration ranged from 30–120 s, and the inter-electrode gap ranged from 0.011 to 0.014 mm. Grey relational analysis (GRA) was interwoven with a fuzzy logic method to optimize the multi-objective technique that was explored in this EDM process. The effect of changing EDM process parameter values on responses was further investigated and statistically analyzed. Additionally, a response graph and response table were produced to determine the best parametric setting based on the calculated grey-fuzzy reasoning grade (GFRG). Furthermore, predictor regression models for response characteristics and GFRG were constructed, and a confirmation test was performed using randomly chosen input parameters to validate the generated models.

Possibilities of Additive Technologies for the Manufacturing of Tooling from Corrosion-Resistant Steels in Order to Protect Parts Surfaces from Thermochemical Treatment

The structure and physical–mechanical properties of products made from powders of corrosion-resistant steel 12X18H10T by the laser-beam powder bed fusion (LB-PBF) and subsequent ion-plasma nitriding in the work were investigated. Comparative studies of the physical mechanical properties of specimens made by the LB-PBF and conventional method from steel of the same grade were carried out. The density of the specimens and the coefficient of linear thermal expansion (CLTE) after the LB-PBF are almost the same as those of the conventionally manufactured specimens. Our analysis of the obtained dilatograms in the temperature range from 20 to 600 °C showed that the CLTE of steel after the LB-PBF is within acceptable limits (18.6 × 10−6 1/°C). Their hardness, tensile strength, yield strength and elongation are higher than those of a conventionally manufactured specimen. The phase composition and structure of specimens of steel 12X18H10T made by the LB-PBF after the process of ion-plasma nitriding were investigated. The obtained results show that the mode of ion-plasma nitriding used in this case (stage 1—570 °C for 36 h; stage 2—540 °C for 12 h) does not lead to deterioration of the characteristics of the selected steel. A technological process for the manufacture of modified tooling from 12X18H10T steel by the LB-PBF was developed. It protects the surfaces that are not subject to nitriding and makes it possible to obtain a uniform high-quality nitrided layer on the working surface of the part made from spheroidal graphite iron.

DETERMINATION OF THE DIMENSIONAL AND TOPOLOGICAL PARAMETERS OF THE GRAPHITE PHASE IN CAST IRON BY FRACTAL ANALYSIS OF IMAGES OF ITS MICROSTRUCTURE

The basics of metallography and modern systems used for studying and analyzing the structures of materials are described. Special attention is paid to the techniques of quantitative microscopy, as a kind of ancestress of modern microstructure analysis systems. The analysis of modern computer programs used to analyze images of microstructures obtained from digital microscopes is presented. The basics of fractal analysis as a highly effective tool for calculating numerical values of parameters of geometrically complex objects are outlined. Using the example of the analysis of graphitized cast iron structure, the application of the fractal analysis method to determine such characteristics of the graphite phase as the shape of graphite inclusions and their distribution in the alloy volume is demonstrated. As part of the study, various classes of cast iron have been studied, such as graphitic pig iron with flaked graphite, cast iron with vermicular graphite, and high-grade cast iron with spheroidal graphite. To determine the shape of graphite inclusions, a fractal dimension has been proposed to be used, and the unevenness of the distribution has been estimated using such a function as lacunarity. The individual stages of determining these characteristics using a specialized FracLac module applied in the structure of the ImageJ program are presented. The obtained results showed high adequacy. Despite positive assessment, the shortcomings identified during the research on the use of fractal analysis methods for identifying geometrically complex dimensional and topological parameters inherent in the graphite phase in cast iron are noted. The ways for further improvement of these methods for solving a wide range of problems in metallography of alloys are proposed.

ISO 185/JL/350

ISO 185/JL/350 is a higher-tensile-strength gray cast iron that has a pearlitic matrix, and a tensile strength of 350–450 MPa (51–65 ksi), when determined on test pieces machined from separately cast, 30 mm (1.2 in.) diameter test bars. It provides a combination of high strength while still maintaining good thermal conductivity compared with other types of cast iron. This grade approaches the maximum tensile strength attainable in gray cast iron. Applications therefore tend to be confined to those where thermal conductivity requirements in service preclude the use of one of the other higher-strength materials such as spheroidal graphite cast irons, which have inferior thermal properties. This datasheet provides information on composition, physical properties, and tensile properties. It also includes information on wear resistance as well as casting and heat treating. Filing Code: CI-85. Producer or source: International Organization for Standardization.