Design and Numerical Simulation of Biomimetic Structures to Capture Particles in a Microchannel

The study of separating different sizes of particles through a microchannel has been an interest in recent years and the primary attention of this study is to isolate the particles to the specific outlets. The present work highly focuses on the design and numerical analysis of a microchip and the microparticles capture using special structures like corrugated dragonfly wing structure and cilia walls. The special biomimetic structured corrugated wing is taken from the cross-sectional area of the dragonfly wing and cilia structure is obtained from the epithelium terminal bronchioles to the larynx from the human body. Parametric studies were conducted on different sizes of microchip scaled and tested up in the range between 2–6 mm and the thickness was assigned as 80 µm in both dragonfly wing structure and cilia walls. The microflow channel is a low Reynolds number regime and with the help of the special structures, the flow inside the microchannel is pinched and a sinusoidal waveform pattern is observed. The pinched flow with sinusoidal waveform carries the particles downstream and induces the particles trapped in desired outlets. Fluid particle interaction (FPI) with a time-dependent solver in COMSOL Multiphysics was used to carry out the numerical study. Two particle sizes of 5 µm and 20 µm were applied, the inlet velocity of 0.52 m/s with an inflow angle of 50° was used throughout the study and it suggested that: the microchannel length of 3 mm with corrugated dragonfly wing structure had the maximum particle capture rate of 20 µm at the mainstream outlet. 80% capture rate for the microchannel length of 3 mm with corrugated dragonfly wing structure and 98% capture rate for the microchannel length of 2 mm with cilia wall structure were observed. Numerical simulation results showed that the cilia walled microchip is superior to the corrugated wing structure as the mainstream outlet can conduct most of the 20 µm particles. At the same time, the secondary outlet can laterally capture most of the 5 µm particles. This biomimetic microchip design is expected to be implemented using the PDMS MEMS process in the future.

Flutter Analysis of a 3D Box-Wing Aircraft Configuration

The aim of this paper is to present a flutter analysis of a 3D Box-Wing Aircraft (BWA) configuration. The box wing structure is considered as consisting of two wings (front and rear wings) connected with a winglet. Plunge and pitch motions are considered for each wing and the winglet is modeled by a longitudinal spring. In order to exert the effect of the wing-joint interactions (bending and torsion coupling), two ends of the spring are located on the gravity centers of the wings tip sections. Wagner unsteady model is used to simulate the aerodynamic force and moment on the wing. The governing equations are extracted via Hamilton’s variational principle. To transform the resulting partial integro-differential governing equations into a set of ordinary differential equations, the assumed modes method is utilized. In order to confirm the aerodynamic model, the flutter results of a clean wing are compared and validated with the previously published results. Also, for the validation, the 3D box wing aircraft configuration flutter results are compared with MSC NASTRAN software and good agreement is observed. The effects of design parameters such as the winglet tension stiffness, the wing sweep and dihedral angles, and the aircraft altitude on the flutter velocity and frequency are investigated. The results reveal that physical and geometrical properties of the front and rear wings and also the winglet design have a significant influence on BWA aeroelastic stability boundary.

Selection of the Optimal Structural Design of a Spar Composite Wing

This paper describes a method for optimizing the design of a spar-type composite aircraft wing structure based on multi-criterion approach. Two types of composite wing structures such as two-spar and three-spar ones were considered. The optimal design of a wing frame was determined by the Pareto method basing on three criteria: minimal weight, minimal wing deflection, maximal safety factor and minimal weight. Positions of wing frame parts, i.e. spars and ribs, were considered as optimization parameters. As a result, an optimal design of a composite spar-type wing was proposed. All the calculations necessary to select the optimal structural and design of the spar composite wing were performed using nonlinear static finite element analysis in the FEMAP with NX Nastran software package.

Improved Immune Genetic Algorithm to Optimize the Design of Wing Structure of Competition Aircraft

An improved immune genetic algorithm is used to design and optimize the wing structure parameters of a competition aircraft. According to the requirements of aircraft design, multi-objective optimization index is established. On this basis, the basic steps of using immune algorithm to optimize the main design parameters of aircraft wing structure are proposed, and the optimization of the wing parameters of a competition aircraft is used as an example for simulation calculation. The design variables in the optimization are the size of the wing components, and the optimization goal is to minimize the weight of the wing and the maximum deformation of the wing structure. Research shows that compared with traditional optimization methods; the improved immune genetic algorithm is a very effective optimization method. At the same time, a prototype is made to check the validity and feasibility of the design. Flight test results show that the optimization method is very effective. Although the method is proposed for competition aircraft, it is also applicable to other types of aircraft.

Integration of Micro-Structured Photovoltaic Cells into the Ultra-Light Wing Structure for Extended Range Unmanned Aerial Vehicles

There have been large developments in the unmanned aerial vehicles (UAV) industry over the last decade. Although UAV development was mainly for military related use in the beginning and despite there being fear surrounding the release of this technology to the open market for quite a long time, nowadays, there are a variety of applications where UAVs are used extensively, such as in agriculture, infrastructure inspection and monitoring, mobile retranslation relays for communications, etc. One of the weaknesses of electrically propelled UAVs is flight autonomy; there is often a difficult trade-of between the weight of the payload, batteries, and surface to be surveyed that is necessary to determine. There have been many attempts to use photovoltaic cells to increase the flight time for UAVs; however, a reliable solution has not yet been developed. The present paper presents improvements that have been conducted to extend the autonomy of electrically derived UAVs: instead of gluing photovoltaic cells on the wings, the new approach embeds the solar cells into the wing structure as well as develops a new wing that is significantly lighter to compensate for the weight added by the photovoltaic cells. It was demonstrated that by using this approach, a 33% increase in the flight time can be achieved with only one modified wing in a prototype vehicle.

Numerical modeling on dynamics of droplet in aircraft wing structure at different velocities

Purpose The purpose of this paper is to find the droplets impact on the airplane wing structure. Two kinds of characteristics of the droplet at different velocity and viscosity are assumed. The droplet is assumed to be spherical cubic form and it is injected from the convergent divergent nozzle with a passive control. Design/methodology/approach This paper presents the results of a numerical simulation of droplet impact on the horizontal surface. The effects of impact parameters are studied. The splash effect of the droplet also visualized. The results are presented in form of stress, strain, displacement magnitude of the droplet. Findings Crosswire is used as passive control. The behavior of the droplet impact is observed based on the kinetic energy and the gravitational forces. Originality/value The results predict that smooth particle hydrodynamic designed droplet not only depend on the equation of state of the droplet but also the injection velocity from the nozzle. It also determined that droplet velocity is depending on the viscosity of the fluid.

MANUFACTURING METHOD OF THE MORPHING WING STRUCTURE FOR UAV BY CFRP WITH APPLYING THE ELECTROFORMED RESIN MOLDING METHOD

Aircraft flight control usually requires driving flaps and ailerons. However, the air drags increase significantly due to the corners of flaps and aileron. Especially, the gap between mother wing and flap / aileron causes a drag increase. Therefore, studies are being conducted on morphing wings that smoothly and greatly deform the wing surface. For aircraft wing, it is needless to say that strength is important to sustain lift and drag for the aircraft during the flight. For morphing wings, in addition, actuators must be mounted inside the wing to enable the morphing deformation. Moreover, for the aircraft wing, weight is quite important. Therefore, carbon fiber reinforced plastic (CFRP) is currently most suitable for aircraft wing structural materials. However, it is difficult to mold CFRP so that it has sufficient strength and can be morphed. In this study, by using CFRP, the morphing wing structure was prototyped with targeting a small unmanned aerial vehicle (UAV) weighing 3 kg. The CFRP lattice structure that enables morphing deformation was designed and manufactured by applying the electrodeposition resin molding (ERM) method which was developed by the authors. In the ERM method, firstly, the carbon fiber was fixed with a jig according to the designed morphing wing structure, and immersed in the electrodeposition solution. Secondly, the epoxy polymer particle in the solution were electrophoresed and impregnated between carbon fibers. After thermal curing, the morphing wing structure was fabricated. Further, the loading-unloading torsion and bending tests of the morphing wing structure were carried out. Smooth morphing deformation and sufficient strength were confirmed.