Electrodeposition of Cu-Ag Alloy Films at n-Si(001) and Polycrystalline Ru Substrates

Electrodeposition of Cu-Ag films from acidic sulfate bath was conducted at n-Si(001) and polycrystalline Ru substrates. Significant nucleation overpotential of 0.4 V is observed with the Cu-Ag bath at n-Si(001) substrate, whereas the electrodeposition of Cu-Ag at Ru substrate is influenced by Ru oxides at the surface. Incomplete coverage of Si substrate by Cu-Ag deposit was observed from the deposition systems without Ag(I), or with 0.1 mM Ag(I), comparing with the compact Cu-Ag film obtained with the deposition bath containing 0.01 mM Ag(I). Layered and faceted Cu-Ag deposit was observed at small Cu deposition overpotential with the Ru substrate. Phase composition of the Cu-Ag deposits at n-Si(001) substrate from electrolyte with various Ag(I) concentrations is examined by XRD. Limited solubility of Ag (0.4 at.%) was observed in fcc-Cu until phase separation occurs. The classical model for nucleation kinetics in electrodeposition was used to examine the potentiostatic transients of the Cu-Ag electrodeposition at n-Si(001) substrate.

A High-Sensitivity SPR Refractive Index Sensor Based on No-Core Fiber with Ag-Cu Composite Films

A fiber/Ag-Cu films surface plasmon resonance (SPR) refractive index (RI) sensor composed of multimode fiber-no-core-fiber-multimode fiber (MMF-NCF-MMF) structure is designed. The sensing region length and Cu film deposition time of sensor are gradually optimized by the control variable method, which finally achieves the improvement of sensor properties. We experimentally compared the sensing performance of the fiber/Ag film and fiber/Ag-Cu films sensor. Experimental results show that the fiber/Ag-Cu films sensor has good linearity (R-square = 0.993), and its sensitivity is as high as 3957 nm/RIU in the refractive index detection range of 1.3328–1.3853, which is 1109 nm/RIU higher than the sensitivity of a conventional fiber/Ag film sensor. The sensor presented in this paper adopts the structure with composite metal film, which outperforms the common single-layer metal film in chemical stability such as oxidation resistance and mechanical hardness. Meanwhile, the SPR sensor with MMF-NCF-MMF structure has the advantages of convenient manufacture and compact structure. In conclusion, it can bestow a unique advantage in the field of biological detection or chemical analysis.

Easily Prepared Transparent Electrodes for Low-Cost Semitransparent Inverted Polymer Solar Cells

The continuous thin film of silver (Ag) film is important for semitransparent electrodes in polymer solar cells, while the Ag atoms form as non-continuous below a critical thickness. Here, semitransparent inverted polymer solar cells were fabricated using thermally evaporated Ag/germanium (Ge)/Ag as highly transparent electrodes. An ultra-thin Ge film was introduced to modify the growth mode of Ag. The dependence of the device performance and the thickness of the outer Ag film was investigated. Ag/Ge/Ag electrodes exhibited excellent optical and electrical properties, which were proved by the transmittance and reflectance spectra. A champion efficiency of 5.1% was achieved with an open-circuit voltage level of 0.703 V, a short current density of 11.63 mA/cm2, and a fill factor of 63%. The average visible transmittance (300–800 nm) of devices with Ag/Ge/Ag was calculated as 25%.

Fluorescence Enhancement via Dual Coupling of Dye Molecules with Silver Nanostructures

We demonstrate the enhancement of fluorescence emitted from dye molecules coupled with two surface plasmons, i.e., silver nanoparticles (AgNPs)-induced localized surface plasmons (LSP) and thin silver (Ag) film supported surface plasmons. Excitation light is illuminated to a SiO2 layer that contains both rhodamine 110 molecules and AgNPs. AgNPs enhances excitation rates of dye molecules in their close proximity due to LSP-induced enhancement of local electromagnetic fields at dye excitation wavelengths. Moreover, the SiO2 layer on one surface of which a 50 nm-thick Ag film is coated for metal cladding (air on the other surface), acts as a waveguide core at the dye emission wavelengths. The Ag film induces the surface plasmons which couple with the waveguide modes, resulting in a waveguide-modulated version of surface plasmon coupled emission (SPCE) for different SiO2 thicknesses in a reverse Kretschmann configuration. We find that varying the SiO2 thickness modulates the fluorescent signal of SPCE, its modulation behavior being in agreement with the theoretical simulation of thickness dependent properties of the coupled plasmon waveguide resonance. This enables optimization engineering of the waveguide structure for enhancement of fluorescent signals. The combination of LSP enhanced dye excitation and the waveguide-modulated version of SPCE may offer chances of enhancing fluorescent signals for a highly sensitive fluorescent assay of biomedical and chemical substances.

Tackling light trapping in organic light-emitting diodes by complete elimination of waveguide modes

Conventional waveguide mode decoupling methods for organic light-emitting diodes (OLEDs) are typically not scalable and increase fabrication complexity/cost. Indium-tin-oxide–free transparent anode technologies showed efficiency improvement without affecting other device properties. However, previous works lack rigorous analysis to understand the efficiency improvement. Here, we introduced an ultrathin silver (Ag) film as transparent electrode and conducted systematic modal analysis of OLEDs and report that waveguide mode can be completely eliminated by designing an OLED structure that is below the cutoff thickness of waveguide modes. We also experimentally verified the waveguide mode removal in organic waveguides with the help of index-matching fluid and prism. The negative permittivity, extremely thin thickness (~5 nanometers), and highly conductive properties achieved by a uniform copper-seeded Ag film can suppress waveguide mode formation, enhancing external quantum efficiency without compromising any other characteristics of OLEDs, which paves the way for cost-effective high-efficiency OLEDs in current display industry.