Co-Channel Interference Suppression for LTE Passive Radar Based on Spatial Feature Cognition

Passive radars based on long-term evolution (LTE) signals suffer from sever interferences. The interferences are not only from the base station used as the illuminator of opportunity (BS-IoO), but also from the other co-channel base stations (CCBS) working at the same frequency with the BS-IoO. Because the reference signals of the co-channel interferences are difficult to obtain, cancellation performance degrades seriously when traditional interference suppression methods are applied in LTE-based passive radar. This paper proposes a cascaded cancellation method based on the spatial spectrum cognition of interference. It consists of several cancellation loops. In each loop, the spatial spectrum of strong interferences is first recognized by using the cyclostationary characteristic of LTE signal and the compressed sensing technique. A clean reference signal of each interference is then reconstructed according to the spatial spectrum previously obtained. With the reference signal, the interferences are cancelled. At the end of each loop, the energy of the interference residual is estimated. If the interference residual is still strong, then the cancellation loop continues; otherwise it terminates. The proposed method can get good cancellation performance with a small-sized antenna array. Theoretical and simulation results demonstrate the effectiveness of the proposed method.

Clutter Suppression Method for Off-Grid Effects Mitigation in Airborne Passive Radars with Contaminated Reference Signals

For an airborne passive radar with contaminated reference signals, the clutter caused by multipath (MP) signals involved in the reference channel (MP clutter) corrupts the covariance estimation in space-time adaptive processing (STAP). In order to overcome the severe STAP performance degradation caused by impure reference signals and off-grid effects, a novel MP clutter suppression method based on local search is proposed for airborne passive radar. In the proposed method, the global dictionary is constructed based on the sparse measurement model of MP clutter, and the global atoms that are most relevant to the residual are selected. Then, the local dictionary is designed iteratively, and local searches are performed to match real MP clutter points. Finally, the off-grid effects are mitigated, and the MP clutter is suppressed from all matched atoms. A range of simulations is conducted in order to demonstrate the effectiveness of the proposed method.

Is It Possible to Obtain Benefits by Reducing the Contribution of the Digital Signal Processing Techniques to the Control of the Active Power Filter?

This paper presents a simple yet efficient control method for active power filters that can be used to improve power quality. Applying this method can open the way towards limiting the hardware and computational expenditure, which are needed for control of the active filter, while maintaining its required performance. The method is based on the indirect approach of obtaining reference signals combined with the closed-loop current control technique. Monitoring of changes of energy stored in reactance elements of the active filter is the base for obtaining reference signals for compensation. The active filter can perform classical compensation and, additionally, can perform some extra functionality for managing of active power in the system. In particular, it can stabilize the supplying source power, enable energy exchange between loads connected on DC and AC sides of the active filter, and—in a case of generating loads—enable their energy storage and redistribution amongst consuming loads. The presented method can be useful for voltage-source as current-source inverter based active filters, and for DC systems as well as for AC single- or three-phase ones.

Performance of the Boost Converter Controlled with ZAD to Regulate DC Signals

This paper presents the performance of a boost converter controlled with a zero average dynamics technique to regulate direct current signals. The boost converter is modeled in a compact form, and a variable change is performed to depend only on the γ parameter. A new sliding surface is proposed, where it is possible to regulate both the voltage and the current with low relative errors with respect to the reference signals. It is analytically demonstrated that the approximation of the switching surface by a piecewise linear technique is efficient in controlling the system. It is shown numerically that for certain operating conditions, the system is evolved into a chaotic attractor. The zero average dynamics technique implemented in the boost converter has good regulation, due to the presence of zones in the bi-parametric space. Furthermore, the zero average dynamics technique regulates the voltage well and presents a chaotic attractor with low steady-state error.

Implementation of coherence-based-selection multi-channel wireless Active Noise Control in headphone

Active noise control (ANC) headphone is widely used to attenuate the noise around human' s ear. The microphone mounted on the conventional ANC headphones collected the mixed reference signals when more than one noise sources are often present in the surrounding. In this case, the uncorrelated noise sources involved in the mixed reference usually deteriorate the noise reduction performance of the ANC headphones. To solve this problem, wireless microphones are proposed to install close to each potential noise source in the environment. The microphones pick up the clean reference signals and transmit them to the ANC controller embedded in the headphones with time-advance wirelessly. Every reference signal selected by a coherence-based-selection algorithm is provided individual control filter in each ear. Each control filter updated by using a single clean reference offers better noise reduction performance for ANC headphones. Furthermore, numerical simulations and real-time experiment results in this paper demonstrate the improvement of the proposed method compared with conventional ANC headphones.

STABILIZATION OF THE REFERENCE SIGNAL PHASE OF THE FIBER OPTICAL DISTRIBUTION UHF SYSTEM

The purpose and composition of the radio-photon components of the fiber-optic distribution system of reference signals of the decimeter wavelength range are described. The principle of the components of the fiber-optic distribution system of reference signals is described. The possibility of creating radio-photon components with improved technical characteristics in comparison with the closest foreign functional analogues has been proved. High technical characteristics are achieved by the original design and parametric compensation of the phase delay of the signal.

Audio Enhancement of Physical Models of Musical Instruments Using Optimal Correction Factors: The Recorder Case

A simulation of a musical instrument is considered to be a successful one when there is a good resemblance between the model’s synthesized sound and the real instrument’s sound. In this work, we propose the integration of physical modeling (PM) methods with an optimization process to regulate a generated digital signal. Its goal is to find a new set of values of the PM’s parameters’ that would lead to a synthesized signal matching as much as possible to reference signals corresponding to the physical musical instrument. The reference signals can be: (a) described by their acoustic characteristics (e.g., fundamental frequencies, inharmonicity, etc.) and/or (b) the signals themselves (e.g., impedances, recordings, etc.). We put this method into practice for a commercial recorder, simulated using the digital waveguides’ PM technique. The reference signals, in our case, are the recorded signals of the physical instrument. The degree of similarity between the synthesized (PM) and the recorded signal (musical instrument) is calculated by the signals’ linear cross-correlation. Our results show that the adoption of the optimization process resulted in more realistic synthesized signals by (a) enhancing the degree of similarity between the synthesized and the recorded signal (the average absolute Pearson Correlation Coefficient increased from 0.13 to 0.67), (b) resolving mistuning issues (the average absolute deviation of the synthesized from the recorded signals’ pitches reduced from 40 cents to the non-noticeable level of 2 cents) and (c) similar sound color characteristics and matched overtones (the average absolute deviation of the synthesized from the recorded signals’ first five partials reduced from 41 cents to 2 cents).