Fatigue Life of Austenitic Steel 304 Bolts Strengthened by Surface Treatment with Graphene Oxide Layer and Surface Shot Peening

This paper presents the results of investigations of the effect of graphene oxide and surface shot peening on the mechanical properties and fatigue life of bolts made of austenitic 304 steel. An innovative method for the uniform deposition of graphene oxide on screws is presented. The process involved activating the surface using plasma and then performing graphene oxide deposition using centrifugal force and vacuum drying. The screw specimens prepared in this way were subjected to a surface peening process. Comparative studies have shown that the combination of graphene oxide deposition and shot peening processes results in an increase in fatigue life of approximately 42 ÷ 275% (depending on the stress amplitude level) compared to the as-delivered samples. The results presented are promising and may provide a basis for further research on the application of graphene and its derivatives to increase fatigue life and improve the mechanical properties of machine components.

The Video Microscopy-Linked Electrochemical Cell: An Innovative Method to Improve Electrochemical Investigations of Biodegradable Metals

An innovative, miniature video-optical-electrochemical cell was developed and tested that allows for the conducting of electrochemical corrosion measurements and simultaneous microscopic observations over a small, well-defined surface area of corroding or degrading samples. The setup consisted of a miniature electrochemical cell that was clamped onto the metal sample and fixed under a video microscope before being filled with electrolyte. The miniature cell was comprised of afferent/efferent electrolyte ducts as well as a connection to the Mini Cell System (MCS) for electrochemical measurements. Consequently, all measured and induced currents and voltages referred to the same small area corroding completely within the field of view of the microscope, thus allowing for real-time observation and linking of surface phenomena such as hydrogen evolution and oxide deposition to electrochemical data. The experimental setup was tested on commercial purity (cp) and extra-high purity (XHP) magnesium (Mg) samples using open circuit potential and cyclic voltammetry methods under static and flowing conditions. The corrosion potential was shifted more anodically for cp Mg in comparison to XHP Mg under dynamic conditions. The corrosion current assessed from the cyclic voltametric curves were higher for the cp Mg in comparison to XHP Mg. However, there were no differences between static and flow conditions in the case of XHP Mg in contrast to cp Mg, where the current density was two times higher at dynamic conditions. The measurements and observations with this new method pave the way for a more detailed understanding of magnesium corrosion mechanisms, thus improving predictive power of electrochemical corrosion measurements on newly developed magnesium or other biodegradable alloys applied for medical devices. Different electrochemical tests can be run under various conditions, while being easy to set up and reproduce as well as being minimally destructive to the sample.

Mechanism of Acidification that Progresses in Library Collections of Books Made of Alkaline Paper

Acidification mechanisms of paper were examined, studying 120 pairs of identical copies of books published from 1971 to 2010 housed in two Japanese university libraries. The pH at the edges of the alkaline paper lowered from 7.5 to 6.4 after 5–10 years and to 5.8 after 10–15 years after publication. The pH bottomed at 5.4 at the edges and at 7.0 in the centre of the sheet. Acid paper showed higher pH at the edges than in the centre of the sheet. The edge pH of the alkaline paper of books stored on an above-ground floor was lower due to more exposure to incoming open air with pollutants compared to paper stored in the basement. Elemental analysis suggested nitrogen oxide deposition, but could not prove sulphur oxide deposition at the edges of the paper. The position-dependent acidification is presumed to relate to the deposition tendency of air pollutants contained in open air, and accordingly the edge pH dropped dramatically. In the 1980s, alkaline paper was increasingly used in the production of books, and it was assumed that no more book acidification was to occur; however, this study concludes that even in alkaline paper, acidification processes will take place over time.

Anodic Aqueous Electrophoretic Deposition of Graphene Oxide on Copper Using Different Cathode Materials

The effect of four different cathode materials on the anodic deposition of graphene oxide (GO) nanosheets was studied experimentally. First, synthesis of graphite oxide from graphite powder was done by modified Hummers' method. Ultrasonic technique was adopted for the preparation of the stable aqueous suspension of GO by using liquid exfoliation of graphite oxide. Deposition of GO coating on copper sheets (the anode) was done via electrophoretic deposition (EPD) at the same operating condition (5V, 2 min, concentration of 0.5 mg/ml of GO per deionized water) with different cathode materials (copper, stainless steel, aluminum and graphite). The coatings’ morphological and microstructure were investigated using scanning electron microscope (SEM) and the effect of the current density in the EPD process was obtained. The change in the deposition weight was also measured. It was ascertained that the cathode’s material is a major factor can affect the GO’s EPD process and the characteristics of the final coating.