On the Optimal Design of Switched-Capacitor Filter Circuits for Analog and Mixed-Signal Integrated Circuit Realization

1994 ◽  
pp. 43-53
Author(s):  
N. C. Gustard ◽  
R. E. Massara
Keyword(s):  
Optimal Design ◽  
Integrated Circuit ◽  
Switched Capacitor ◽  
Circuit Realization ◽  
Mixed Signal

A Simplicial PWL Integrated Circuit Realization

2007 ◽  
Author(s):  
Martin Di Federico ◽  
Pedro Julian ◽  
Tomaso Poggi ◽  
Marco Storace
Keyword(s):  
Integrated Circuit ◽  
Circuit Realization

A tri-mode 802.11 baseband PHY mixed signal integrated circuit in 0.13-μm CMOS

2004 ◽  
Author(s):  
Philip J. Ryan ◽  
Brian Hart ◽  
Mike Webb ◽  
Kevin Wong
Keyword(s):  
Integrated Circuit ◽  
Mixed Signal

scholarly journals Achieving Energy Efficiency in Analogue and Mixed Signal Integrated Circuit Design

10.5772/38356 ◽  
2012 ◽  
Author(s):  
E. Lpez-Morillo ◽  
F. Mrquez ◽  
T. Snchez-Rodrguez ◽  
C.I. Lujn-Martnez ◽  
F. Munoz
Keyword(s):  
Energy Efficiency ◽  
Circuit Design ◽  
Integrated Circuit ◽  
Integrated Circuit Design ◽  
Mixed Signal

Teaching Mixed-Signal Integrated Circuit Design to Undergraduates

2006 ◽  
Vol 49 (1) ◽  
pp. 39-48 ◽  
Author(s):  
T.A. Hudson ◽  
E.R. Doering ◽  
G. Lee-Thomas
Keyword(s):  
Circuit Design ◽  
Integrated Circuit ◽  
Integrated Circuit Design ◽  
Mixed Signal

scholarly journals A Fully-Differential Switched-Capacitor Dual-Slope Capacitance-To-Digital Converter (CDC) for a Capacitive Pressure Sensor

Sensors ◽  
2019 ◽  
Vol 19 (17) ◽  
pp. 3673
Author(s):  
Christopher Rogi ◽  
Cesare Buffa ◽  
Niccolo De Milleri ◽  
Richard Gaggl ◽  
Enrique Prefasi
Keyword(s):  
Pressure Sensor ◽  
Integrated Circuit ◽  
Ambient Air ◽  
Micro Electro Mechanical System ◽  
Switched Capacitor ◽  
Capacitive Pressure Sensor ◽  
Fully Differential ◽  
Sensor Model ◽  
Low Performance ◽  
On Chip

This article focuses on a proposed Switched-Capacitor Dual-Slope based CDC. Special attention is paid to the measurement setup using a real pressure sensor. Performance scaling potential as well as dead zones are pointed out and discussed. In depth knowledge of the physical sensor behavior is key to design an optimal readout circuit. While this is true for high-end applications, low-performance IoT (Internet of Things) sensors aim at moderate resolution with very low power consumption. This article also provides insights into basic MEMS (Micro-Electro-Mechanical-System) physics. Based on that, an ambient air pressure sensor model for SPICE (Simulation-Program-with-Integrated-Circuit-Emphasis) circuit simulators is presented. The converter concept was proven on silicon in a 0.13 μ m process using both a real pressure sensor and an on-chip dummy MEMS bridge. A 3.2-ms measurement results in 13-bit resolution while consuming 35 μ A from a 1.5-V supply occupying 0.148 mm2. A state-of-the-art comparison identifies potential room for improvements towards hybrid solutions, which is proposed in subsequent publications already.

A custom mixed-signal cmos integrated circuit for high performance pet tomograph front-end applications

2003 ◽  
Vol 50 (4) ◽  
pp. 909-914 ◽  
Author(s):  
B.K. Swann ◽  
J.M. Rochelle ◽  
D.M. Binkley ◽  
B.S. Puckett ◽  
B.J. Blalock ◽  
...  
Keyword(s):  
Integrated Circuit ◽  
High Performance ◽  
Mixed Signal ◽  
Cmos Integrated Circuit ◽  
Front End
Sign in / Sign up

Export Citation Format

Share Document