Influence of Strip Cooling Rate on Lüders Bands Appearance During Subsequent Cold Deformation

2019 ◽  
pp. 115-121
Author(s):  
Rešković Stoja ◽  
Brlić Tin ◽  
Jandrlić Ivan ◽  
Vodopivec Franc
Keyword(s):  
Cooling Rate ◽  
Cold Deformation ◽  
Lüders Bands

scholarly journals Structure and Mechanical Properties of AlMg4.5 And AlMg4.5Mn Wires Extruded by Kobo Method

2014 ◽  
Vol 59 (2) ◽  
pp. 473-479 ◽  
Author(s):  
M. Jaskowski ◽  
K. Pieła ◽  
L. Błaz
Keyword(s):  
Mechanical Properties ◽  
Work Hardening ◽  
Flow Instability ◽  
Cold Deformation ◽  
Tensile Tests ◽  
Strength Properties ◽  
Extrusion Ratio ◽  
Groove Rolling ◽  
One Step ◽  
Lüders Bands

Abstract The influence of the number of extrusion steps in KoBo method (at the same total extrusion ratio of λ = 100) on structure, mechanical properties and work hardening characteristics of AlMg4.5 and AlMg4.5Mn (AA5083) alloys was investigated. It was found that one-step extrusion leads to the formation of recrystallised structure of the material, while the use of two-step extrusion yields a fibrous structure of a “mixed” type, i.e. containing areas where the intensive recovery effects are associated with partially recrystallised structure. As a consequence, the strength properties of the latter extrudate are much higher in both as extruded state and after the subsequent cold rolling. In all cases, the tensile stress-strain curves of the extrudates show the flow stress serrations that are typical for the Portevin - LeChatelier (P-L) effect. In a few tensile tests, the P-L effect was preceded by the plastic flow instability being typical for the occurrence of Lüders bands. Both AlMg4.5 and AlMg4.5Mn extruded wires show a monotonic increase of the work hardening that results from the following cold deformation in the groove rolling.

Influence of Cooling Rate on Free Interstitial Concentration in Type 430 Ferritic Stainless Steel

2014 ◽  
Vol 611-612 ◽  
pp. 111-116 ◽  
Author(s):  
Timo J. Juuti ◽  
Timo Manninen ◽  
David Porter
Keyword(s):  
Stainless Steel ◽  
Cooling Rate ◽  
Ferritic Stainless Steel ◽  
Volume Fraction ◽  
Post Annealing ◽  
The Matrix ◽  
Free Interstitial ◽  
C And N ◽  
Kinetic Calculations ◽  
Lüders Bands

In ferritic steels, the amount of free C and N should be as low as possible to avoid the formation of Cottrell atmospheres and their associated discontinuous yielding and Lüders bands during forming. During the post-annealing cooling of ferritic stainless steel, carbides and nitrides of the type MX and M23C6precipitate. The volume fraction of the precipitates is determined by chemical composition, microstructure and the cooling path. In some cases, precipitation might not be sufficient to remove all free interstitials from the matrix, in which case, the process parameters or composition of the steel should be reconsidered. Here, thermodynamic and kinetic calculations using Thermo-calc and TC Prisma software have been made to investigate the precipitation of C and N as a function of total interstitial content and cooling rate. According to the calculations, decreasing the cooling rate would result in a more efficient precipitation and hence, less free C and N in the matrix, but the amount is not sufficient to remove the upper yield point. Furthermore, changing the C and N content of the steel was found to have insignificant influence. However, the free C and N could possible be bound through a more complex cooling.

scholarly journals The Interdependence of the Degree of Precipitation and Dislocation Density during the Thermomechanical Treatment of Microalloyed Niobium Steel

Metals ◽  
2020 ◽  
Vol 10 (2) ◽  
pp. 294
Author(s):  
Stoja Rešković ◽  
Ljerka Slokar Benić ◽  
Martina Lovrenić-Jugović
Keyword(s):  
Dislocation Density ◽  
Thermomechanical Processing ◽  
Cold Deformation ◽  
Industrial Process ◽  
Recrystallization Process ◽  
Density Of Dislocations ◽  
Niobium Microalloyed Steel ◽  
Rolling Temperatures ◽  
Final Rolling ◽  
Lüders Bands

In this paper, thermomechanical processing of niobium microalloyed steel was performed with the purpose of determining the interaction between niobium precipitates and dislocations, as well as determining the influence of the temperature of final deformation on the degree of precipitation and dislocation density. Two variants of thermomechanical processing with different final rolling temperatures were carried out. Samples were studied using electrochemical isolation with an atomic absorption spectrometer, transmission electron microscopy, X-ray diffraction analysis, and universal tensile testing with a thermographic camera. The results show that the increase in the density of dislocations before the onset of intense precipitation is insignificant because the recrystallization process takes place simultaneously. It increases with the onset of strain-induced precipitation. In this paper, it is shown that niobium precipitates determine the density of dislocations. The appearance of Lüders bands was noticed as a consequence of the interaction between niobium precipitates and dislocations during the subsequent cold deformation. In both variants of the industrial process performed on the cold deformed strip, Lüders bands appeared.

Effects of cooling rate on the mechanical properties of dual phase treated vanadium steels

1983 ◽  
Vol 41 ◽  
pp. 220-221
Author(s):  
L.J. Chen ◽  
H.C. Cheng ◽  
J.R. Gong ◽  
J.G. Yang
Keyword(s):  
Mechanical Properties ◽  
Cooling Rate ◽  
Automobile Industry ◽  
High Strength ◽  
Weight Percent ◽  
Low Alloy Steels ◽  
Dual Phase ◽  
Resource Requirement ◽  
Alloy Steels ◽  
Potential Weight

For fuel savings as well as energy and resource requirement, high strength low alloy steels (HSLA) are of particular interest to automobile industry because of the potential weight reduction which can be achieved by using thinner section of these steels to carry the same load and thus to improve the fuel mileage. Dual phase treatment has been utilized to obtain superior strength and ductility combinations compared to the HSLA of identical composition. Recently, cooling rate following heat treatment was found to be important to the tensile properties of the dual phase steels. In this paper, we report the results of the investigation of cooling rate on the microstructures and mechanical properties of several vanadium HSLA steels.The steels with composition (in weight percent) listed below were supplied by China Steel Corporation: 1. low V steel (0.11C, 0.65Si, 1.63Mn, 0.015P, 0.008S, 0.084Aℓ, 0.004V), 2. 0.059V steel (0.13C, 0.62S1, 1.59Mn, 0.012P, 0.008S, 0.065Aℓ, 0.059V), 3. 0.10V steel (0.11C, 0.58Si, 1.58Mn, 0.017P, 0.008S, 0.068Aℓ, 0.10V).

Suppression of γ’ Precipitation in a Laser-Melted Nickel-Base Alloy

1977 ◽  
Vol 35 ◽  
pp. 270-271
Author(s):  
J. M. Walsh ◽  
J. C. Whittles ◽  
B. H. Kear ◽  
E. M. Breinan
Keyword(s):  
Cooling Rate ◽  
Base Alloy ◽  
Material Surface ◽  
Intimate Contact ◽  
Absorbed Power ◽  
Perfect Contact ◽  
Nickel Base ◽  
Rapidly Solidified ◽  
Limiting Case ◽  
The Heat Transfer Coefficient

Conventionally cast γ’ precipitation hardened nickel-base superalloys possess well-defined dendritic structures and normally exhibit pronounced segregation. Splat quenched, or rapidly solidified alloys, on the other hand, show little or no evidence for phase decomposition and markedly reduced segregation. In what follows, it is shown that comparable results have been obtained in superalloys processed by the LASERGLAZE™ method.In laser glazing, a sharply focused laser beam is traversed across the material surface at a rate that induces surface localized melting, while avoiding significant surface vaporization. Under these conditions, computations of the average cooling rate can be made with confidence, since intimate contact between the melt and the self-substrate ensures that the heat transfer coefficient is reproducibly constant (h=∞ for perfect contact) in contrast to the variable h characteristic of splat quenching. Results of such computations for pure nickel are presented in Fig. 1, which shows that there is a maximum cooling rate for a given absorbed power density, corresponding to the limiting case in which melt depth approaches zero.

Voids in Quenched Nickel

1968 ◽  
Vol 26 ◽  
pp. 266-267
Author(s):  
J. J. Laidler
Keyword(s):  
Electron Beam ◽  
Ambient Temperature ◽  
Cooling Rate ◽  
Three Dimensional ◽  
Cooling Curve ◽  
Polycrystalline Nickel ◽  
Quenching Temperature ◽  
Long Tail ◽  
Diffusion Pump

The presence of three-dimensional voids in quenched metals has long been suspected, and voids have indeed been observed directly in a number of metals. These include aluminum, platinum, and copper, silver and gold. Attempts at the production of observable quenched-in defects in nickel have been generally unsuccessful, so the present work was initiated in order to establish the conditions under which such defects may be formed.Electron beam zone-melted polycrystalline nickel foils, 99.997% pure, were quenched from 1420°C in an evacuated chamber into a bath containing a silicone diffusion pump fluid . The pressure in the chamber at the quenching temperature was less than 10-5 Torr . With an oil quench such as this, the cooling rate is approximately 5,000°C/second above 400°C; below 400°C, the cooling curve has a long tail. Therefore, the quenched specimens are aged in place for several seconds at a temperature which continuously approaches the ambient temperature of the system.

Microstructures of Laser Processed Fe-Cr Surface Alloys

1981 ◽  
Vol 39 ◽  
pp. 328-329
Author(s):  
P. A. Molian ◽  
K. H. Khan ◽  
W. E. Wood
Keyword(s):  
Cooling Rate ◽  
Pure Iron ◽  
Continuous Wave ◽  
Laser Surface ◽  
Material Surface ◽  
Constitution Diagram ◽  
Incident Power ◽  
Surface Alloying ◽  
Laser Surface Alloying ◽  
Spot Diameter

In recent years, the effects of chromium on the transformation characteristics of pure iron and the structures produced thereby have been extensively studied as a function of cooling rate. In this paper, we present TEM observations made on specimens of Fe-10% Cr and Fe-20% Cr alloys produced through laser surface alloying process with an estimated cooling rate of 8.8 x 104°C/sec. These two chromium levels were selected in order to study their phase transformation characteristics which are dissimilar in the two cases as predicted by the constitution diagram. Pure iron (C<0.01%, Si<0.01%, Mn<0.01%, S=0.003%, P=0.008%) was electrodeposited with chromium to the thicknesses of 40 and 70μm and then vacuum degassed at 400°F to remove the hydrogen formed during electroplating. Laser surface alloying of chromium into the iron substrate was then performed employing a continuous wave CO2 laser operated at an incident power of 1200 watts. The laser beam, defocussed to a spot diameter of 0.25mm, scanned the material surface at a rate of 30mm/sec, (70 ipm).

STUDY OF THE DEPENDENCE OF THE CRYSTALLIZATION PROCESSES OF POLYMER MICROCOMPOSITES ON THE COOLING RATE

2017 ◽  
Author(s):  
◽  
Nataliia Fialko ◽  
Viktor Prokopov ◽  
Julii Sherenkovskiy ◽  
Nataliia Meranova ◽  
...  
Keyword(s):  
Cooling Rate ◽  
Crystallization Process

The analysis of the effect of the cooling rate on the main parameters of the crystallization process from the melt of composites obtained based on various matrices - polyethylene, polypropylene and polycarbonate, using copper microparticles as a filler is carried out.

Sign in / Sign up

Export Citation Format

Share Document