Experimental Effect of Cutting Parameters and Tool Geometry in Drilling Woven CFRP

2019 ◽  
pp. 135-142 ◽  
Author(s):  
Amani Mahdi ◽  
Yosra Turki ◽  
Zoubeir Bouaziz ◽  
Malek Habak ◽  
Souhail El Bouami
Keyword(s):  
Cutting Parameters ◽  
Tool Geometry ◽  
Experimental Effect

scholarly journals Effect of Cutting Parameters and Tool Geometry on the Performance Analysis of One-Shot Drilling Process of AA2024-T3

Metals ◽  
2021 ◽  
Vol 11 (6) ◽  
pp. 854
Author(s):  
Muhammad Aamir ◽  
Khaled Giasin ◽  
Majid Tolouei-Rad ◽  
Israr Ud Din ◽  
Muhammad Imran Hanif ◽  
...  
Keyword(s):  
Feed Rate ◽  
Surface Defects ◽  
Thrust Force ◽  
Cutting Tools ◽  
Chip Thickness ◽  
Cutting Parameters ◽  
Spindle Speed ◽  
Machining Process ◽  
Tool Geometry ◽  
Drilling Process

Drilling is an important machining process in various manufacturing industries. High-quality holes are possible with the proper selection of tools and cutting parameters. This study investigates the effect of spindle speed, feed rate, and drill diameter on the generated thrust force, the formation of chips, post-machining tool condition, and hole quality. The hole surface defects and the top and bottom edge conditions were also investigated using scan electron microscopy. The drilling tests were carried out on AA2024-T3 alloy under a dry drilling environment using 6 and 10 mm uncoated carbide tools. Analysis of Variance was employed to further evaluate the influence of the input parameters on the analysed outputs. The results show that the thrust force was highly influenced by feed rate and drill size. The high spindle speed resulted in higher surface roughness, while the increase in the feed rate produced more burrs around the edges of the holes. Additionally, the burrs formed at the exit side of holes were larger than those formed at the entry side. The high drill size resulted in greater chip thickness and an increased built-up edge on the cutting tools.

Optimization of Tool Geometry and Cutting Parameters for Hard Turning

2007 ◽  
Vol 22 (1) ◽  
pp. 15-21 ◽  
Author(s):  
Dilbag Singh ◽  
P. Venkateswara Rao
Keyword(s):  
Hard Turning ◽  
Cutting Parameters ◽  
Tool Geometry

scholarly journals Tool geometry analysis for plunge milling of lead-free CuZn-alloys

2021 ◽  
Author(s):  
Stefan Baier ◽  
Lukas Kokozinski ◽  
Daniel Schraknepper ◽  
Thomas Bergs
Keyword(s):  
Cutting Parameters ◽  
Lead Free ◽  
Tool Geometry ◽  
Work Piece ◽  
Plunge Milling ◽  
Process Step ◽  
Pilot Hole ◽  
Electrical Connector ◽  
Cutting Force Components ◽  
Force Components

Plunge milling is a critical process step in mass manufacturing of rectangular shapes in electrical connector components. These shapes are manufactured by drilling a pilot hole and subsequent plunge milling with a radial offset (pitch) one or more times. The plunged cavity serves as guidance for the final broaching cut. In light of new legislative initiatives, the electronics industry is forced to use lead-free Cu-Zn-Alloys for mass manufacturing of these connectors. The plunging tool is deflected due to the higher cutting forces experienced in machining of lead-free CuZn-alloys in comparison to alloys with lead. This results in an offset of the milled cavity and negatively impacts tool guidance in the subsequent broaching process. Therefore, the geometric tolerances cannot be met. In this paper, the effect of tool geometry and cutting parameters on the workpiece geometry in plunge milling is investigated. The effect of the microstructure of the work-piece materials CuZn37, CuZn42 and CuZn21Si3P on the tool deflection and cutting force components is examined. The tools used vary regarding the design of the corner in terms of the corner chamfer and the inner shaft thickness. Friction between chips in the tools inner flutes and the cavity walls reduced workpiece accuracy. Improvements were achieved by reducing the width of the cutting corner chamfers, using large inner flutes and applying low cutting parameters.

Statistical Cutting Force Model for Orthogonal Cutting of Polytetrafluoroethylene (PTFE) Composites

2013 ◽  
Author(s):  
Felicia Stan ◽  
Daniel Vlad ◽  
Catalin Fetecau
Keyword(s):  
Friction Coefficient ◽  
Cutting Force ◽  
Feed Rate ◽  
Normal Force ◽  
Polynomial Regression ◽  
Orthogonal Cutting ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Tool Geometry ◽  
Force Model

This paper presents an experimental investigation of the cutting forces response during the orthogonal cutting of polytetrafluoroethylene (PTFE) and PTFE-based composites using the Taguchi method. Cutting experiments were conducted using the L27 orthogonal array and the effects of the cutting parameters (feed rate, cutting speed and rake angle) on the cutting force were analyzed using the S/N ratio response and the analysis of variance (ANOVA). Statistical models that correlate the cutting force with process variables were developed using ANOVA and polynomial regression. The variation of the apparent friction coefficient was analyzed with respect to tool geometry and the cutting process. The results indicated that cutting and thrust forces increase with increasing feed rate, and decrease with increasing rake angles from negative to positive values and increasing cutting speed. A power law relationship between the apparent friction coefficient and the normal force exerted by the chip on the tool-rake face was identified, the former decreasing with an increasing normal force.

Effects of Cutting Parameters on Chip Side-Curl Mechanisms and Variable Tool-Chip Contact in Turning

1999 ◽  
Author(s):  
A. K. Balaji ◽  
I. S. Jawahir
Keyword(s):  
High Speed ◽  
Cutting Parameters ◽  
Sem Analysis ◽  
Tool Geometry ◽  
Depth Of Cut ◽  
Nose Radius ◽  
Turning Operations ◽  
Variable Friction ◽  
On Chip ◽  
Bar Turning

Abstract This paper presents the results of an investigative study on the chip side-curling mechanism and the associated variable tool-chip contact in turning operations. The effect of various cutting and tool geometry parameters such as depth of cut-nose radius ratio, feed, inclination angle, etc. on chip side-curling are established in a hierarchical manner. The importance of variable friction at the tool-chip interface along the developed length of the cutting edge is shown from the experimental observations of the tool-chip contact area using a SEM analysis. The significant influence of the radial cutting force component on the resultant chip side-curl is established using a high speed-filming analysis of comparative experiments in tube and bar turning operations.

Optimisation of the Bauer Equation Using the Least Squares Method for Thermoplastics Turning

2018 ◽  
Vol 8 (1) ◽  
pp. 21-36
Author(s):  
János Farkas ◽  
Etele Csanády ◽  
Levente Csóka
Keyword(s):  
Surface Roughness ◽  
Least Squares Method ◽  
Composite Ceramic ◽  
Cutting Parameters ◽  
Machining Process ◽  
Tool Geometry ◽  
Machining Processes ◽  
Simple Formulation ◽  
Plastic Composite ◽  
Cutting Speeds

A number of equations are available for predicting the output of machining processes. These equations are most commonly used for the prediction of surface roughness after tooling. Surface roughness can be influenced by many factors, including cutting parameters, tool geometry and environmental factors such as the coolant used. It is difficult to create a universally applicable equation for all machining because of the variations in different materials' behaviours (e.g. metal, wood, plastic, composite, ceramic). There are also many differences between the various types of machining process such as the machining tools, rotational or translational movements, cutting speeds, cutting methods, etc. The large number of parameters required would make such an equation unusable, and difficult to apply quickly. The goal is thus to create a simple formulation with three or four inputs to predict the final surface roughness of the machined part within adequate tolerances. The two main equations used for this purpose are the Bauer and Brammertz formulas, both of which need to be optimised for a given material. In this paper, the turning of thermoplastics was investigated, with the aim of tuning the Bauer formula for use with thermoplastics. Eleven different plastics were used to develop a material-dependent surface roughness equation. Only new tooling inserts were used to eliminate the effects of tool wear.

Model-based sensitivity analysis of machining-induced residual stress under minimum quantity lubrication

2015 ◽  
Vol 231 (9) ◽  
pp. 1528-1541 ◽  
Author(s):  
Xia Ji ◽  
Steven Y Liang
Keyword(s):  
Residual Stress ◽  
Sensitivity Analysis ◽  
Cutting Force ◽  
Cutting Temperature ◽  
Minimum Quantity Lubrication ◽  
Cutting Parameters ◽  
Tool Geometry ◽  
Depth Of Cut ◽  
Mixture Ratio ◽  
Minimum Quantity

This article presents a sensitivity analysis of residual stress based on the verified residual stress prediction model. The machining-induced residual stress is developed as a function of cutting parameters, tool geometry, material properties, and lubrication conditions. Based on the residual stress predictive model, the main effects of the cutting force, cutting temperature, and residual stress are quantitatively analyzed through the cosine amplitude method. The parametric study is carried out to investigate the effects of minimum quantity lubrication parameters, cutting parameters, and tool geometry on the cutting performances. Results manifest that the cutting force and residual stress are more sensitive to the heat transfer coefficient and the depth of cut, while the cutting temperature is more sensitive to the cutting speed. Large maximum compressive residual stress is obtained under a lower flow rate of minimum quantity lubrication, small depth of cut, and the proper air–oil mixture ratio. This research can support the controlling and optimization of residual stress in industrial engineering by strategically adjusting the application parameters of minimum quantity lubrication.

Experimental Investigation on the Effect of Tool Geometry and Cutting Conditions Using Tool Wear Prediction Model for End Milling Process

2014 ◽  
Vol 13 (01) ◽  
pp. 41-54 ◽  
Author(s):  
S. Kalidass ◽  
P. Palanisamy
Keyword(s):  
Tool Wear ◽  
End Milling ◽  
Cutting Parameters ◽  
304 Stainless Steel ◽  
Tool Geometry ◽  
Depth Of Cut ◽  
Work Piece ◽  
Cutting Condition ◽  
Machining Parameter

Tool wear of a cutting tool has a significant impact on the tool life and surface quality of the finished product. Tool wear is influenced by many factors such as cutting parameters, tool geometry, coating type, work piece material, chatter, and cutting condition. In the present work, the design of experiments (DOE) technique has been used for four factors at five levels to conduct experiments. Tool wear is taken as the response variable measured during end milling, while helix angle, spindle speed, feed and depth of cut are taken as the input parameters. The material and tool selected for this study are AISI 304 stainless steel and uncoated solid carbide end mill cutter respectively. The tool wear was measured using tool maker's microscope. The experimental values are used in six sigma software for finding the coefficients to develop the regression model. The direct and interaction effect of the machining parameter with tool wear were analyzed using contour graphs, which helped to select process parameters for reducing tool wear and also ensure quality of milling.

Finite Element Analysis of Burr Formation in Micro-Machining

2014 ◽  
Vol 487 ◽  
pp. 225-229
Author(s):  
Juan Huang ◽  
Yong Hua Xiong ◽  
Jin Gui Huang ◽  
Gui Cheng Wang
Keyword(s):  
Finite Element ◽  
High Surface ◽  
Cutting Parameters ◽  
Burr Formation ◽  
Contact Friction ◽  
Tool Geometry ◽  
Work Piece ◽  
Micro Cutting ◽  
Finite Element Software ◽  
General Law

In the process of micro-cutting for the precision small parts, one of the main problems is the micro burrs. The finite element software Abaqus was used to simulate the micro-cutting process of aluminum 2024-T3. To create this model, Johnson-Cook (J-C) model was used to establish the material model, and Arbitrary Lagrangian Eulerian (ALE) method was used to separate the chip from work-piece. The contact friction models which was used between chip and tool was the modified Coulomb friction law. The formation process of micro burrs was simulated dynamically, and the effect of different cutting parameters and tool geometry parameters on burrs forming was analyzed. Furthermore, the general law was obtained. The results provide the guidance for optimizing the tool geometry parameters and cutting parameters to reduce the burrs in micro-cutting with the high surface quality.

Sign in / Sign up

Export Citation Format

Share Document