The Restoration Proposal for the 4-storey Load Bearing Timber Structure of Matsopoulos Wheat Mill in Trikala (Greece)

2021 ◽  
pp. 790-803
Author(s):  
Eleftheria Tsakanika ◽  
Sonia Charalambides
2020 ◽  
Vol 6 (12) ◽  
pp. 2437-2447
Author(s):  
João H. Negrão

This paper describes the rehabilitation procedure of the roof timber structure of a multiuse pavilion in Viseu, Portugal. The roof structure consists of a series of parallel double timber trusses, partially concealed above a polyhedral wooden plank-made ceiling. Recently, the support of one of the trusses failed and another one has been assessed as in a pre-failure condition. Some load-redistribution and the prompt shore of the structure prevented the generalized collapse. The subsequent inspection and assessment led to the conclusion that the primary cause of the collapse was the failure perpendicular to the grain of the solid timber elements inserted between the double rafters and tie-beams. The replacement of the existing with a steel structure, and the repair and reinforcement of the existing wooden trusses, were considered as intervention possibilities. The latter revealed much cheaper, less time-consuming and in line with the international recommendations on rehabilitation works, and was therefore adopted. An innovative solution, consisting of the replacement of the central timber elements in all the supports, resulted in minimum visual impact and improved the load bearing capability beyond its original value. Doi: 10.28991/cej-2020-03091628 Full Text: PDF


1993 ◽  
Vol 06 (02) ◽  
pp. 100-104 ◽  
Author(s):  
D. M. Pickles ◽  
C. R. Bellenger

SummaryTotal removal of a knee joint meniscus is followed by osteoarthritis in many mammalian species. Altered load-bearing has been observed in the human knee following meniscectomy but less is known about biochemical effects of meniscectomy in other species. Using pressure sensitive paper in sheep knee (stifle) joints it was found that, for comparable loads, the load-bearing area on the medial tibial condyle was significantly reduced following medial meniscectomy. Also, for loads of between 50 N and 500 N applied to the whole joint, the slope of the regression of contact area against load was much smaller. Following medial meniscectomy, the ability to increase contact area as load increased was markedly reduced.The load bearing area on the medial tibial condyle was reduced following meniscectomy.


2015 ◽  
Vol 10 (2) ◽  
pp. 25-34
Author(s):  
Kristian Sogel
Keyword(s):  

Author(s):  
I.O. Egorochkina ◽  
◽  
I.A. Serebryanaya ◽  
S. A. Jamaldinov ◽  
F.A. Bataeva ◽  
...  

The article describes the features of construction and technical expertise of structures of agricultural warehouse of mineral fertilizers. A draft program for visual and detailed instrumental inspection of building load-bearing structures has been developed. In accordance with the recommendations of the regulatory and technical documentation, measures have been developed to repair and restore the functional state of damaged structures.


Author(s):  
Y.P. Manshin ◽  
◽  
E.Yu. Manshina ◽  

The article considers an algorithm for analyzing the results of field strain-measurement studies of machine structures, which allows obtaining data for the modernization of elements in the form of coefficients of parameter changes. As the object of application of the method, the design element of the header was selected, which had failures due to insufficient endurance under cyclic bending stresses.


2001 ◽  
Vol 85 (5) ◽  
pp. 38-45
Author(s):  
Ari Aalto ◽  
Markku Tuomala
Keyword(s):  

2020 ◽  
Vol 62 (1) ◽  
pp. 55-60
Author(s):  
Per Heyser ◽  
Vadim Sartisson ◽  
Gerson Meschut ◽  
Marcel Droß ◽  
Klaus Dröder

Alloy Digest ◽  
2017 ◽  
Vol 66 (2) ◽  

Abstract Strenx 700 is a high-strength structural steel with a minimum yield strength of 650–700 MPa (94–102 ksi) depending on thickness. Strenx 700 meets the requirements of EN 10 025-6 for the S690 grade and thicknesses. Typical applications include demanding load-bearing structures. This datasheet provides information on composition, physical properties, and tensile properties as well as fracture toughness. It also includes information on surface qualities as well as forming, machining, and joining. Filing Code: SA-779. Producer or source: SSAB Swedish Steel Inc..


Sign in / Sign up

Export Citation Format

Share Document