Effect of Filler Content on the Performance of Epoxy/Haritaki Powder Composite

2021 ◽  
pp. 277-283
Author(s):  
N. Narmadadevi ◽  
V. Velmurugan ◽  
R. Prabhakaran ◽  
R. Venkatakrishnan
Keyword(s):  
Filler Content ◽  
Powder Composite

Starch-modified fillers for linerboard and paper grades: A perspective review

TAPPI Journal ◽  
2010 ◽  
Vol 9 (4) ◽  
pp. 31-36 ◽  
Author(s):  
YULIN DENG ◽  
PHIL JONES ◽  
LESLIE MCLAIN ◽  
ART J. RAGAUSKAS
Keyword(s):  
Filler Content ◽  
Product Platform ◽  
Laboratory Studies ◽  
The Past ◽  
Development Opportunity ◽  
Laboratory Results ◽  
Addition Rate ◽  
Institute Of Technology ◽  
Paper Product ◽  
Detrimental Impact

High-filler-content paper is a growing research and development opportunity in papermaking. These new products must address traditional paper product properties while providing papermakers with distinct product platform benefits. Over the past decade, a research team involving researchers from the Institute of Paper Science and Technology at Georgia Institute of Technology and from Imerys have significantly advanced the application of starch-encapsulated papermaking fillers. This review summarizes these accomplishments from initial laboratory studies to mill trials. Laboratory results have illustrated that starch-encapsulated fillers can facilitate a near-doubling of filler content over conventional levels at equal tensile and z-direction tensile (ZDT) values. Equally important is that the use of starch-encapsulated kaolin (SEK) filler has been shown to facilitate a doubling of filler addition rate without any detrimental impact on ring crush compared with control studies with filler. Pilot-plant and mill trials have shown that SEK can function as a fiber extender, reduce steam demand for drying by 10%, and increase papermaking speeds and production rates.

scholarly journals Common Origin of Filler Network Related Contributions to Reinforcement and Dissipation in Rubber Composites

Polymers ◽  
2021 ◽  
Vol 13 (15) ◽  
pp. 2534
Author(s):  
Sriharish Malebennur Nagaraja ◽  
Sven Henning ◽  
Sybill Ilisch ◽  
Mario Beiner
Keyword(s):  
Network Topology ◽  
Filler Content ◽  
Matrix Composition ◽  
Rubber Matrix ◽  
Butadiene Rubber ◽  
Rubber Composites ◽  
Different Temperatures ◽  
Filler Network ◽  
General Perspective ◽  
Rubber Filler

A comparative study focusing on the visco–elastic properties of two series of carbon black filled composites with natural rubber (NR) and its blends with butadiene rubber (NR-BR) as matrices is reported. Strain sweeps at different temperatures are performed. Filler network-related contributions to reinforcement (ΔG′) are quantified by the classical Kraus equation while a modified Kraus equation is used to quantify different contributions to dissipation (ΔGD″, ΔGF″). Results indicate that the filler network is visco-elastic in nature and that it is causing a major part of the composite dissipation at small and intermediate strain amplitudes. The temperature dependence of filler network-related reinforcement and dissipation contributions is found to depend significantly on the rubber matrix composition. We propose that this is due to differences in the chemical composition of the glassy rubber bridges connecting filler particles since the filler network topology is seemingly not significantly influenced by the rubber matrix for a given filler content. The underlying physical picture explains effects in both dissipation and reinforcement. It predicts that these glassy rubber bridges will soften sequentially at temperatures much higher than the bulk Tg of the corresponding rubber. This is hypothetically due to rubber–filler interactions at interfaces resulting in an increased packing density in the glassy rubber related to the reduction of free volume. From a general perspective, this study provides deeper insights towards the molecular origin of reinforcement and dissipation in rubber composites.

scholarly journals Piezoresistive Characteristics of Nanocarbon Composite Strain Sensor by Its Longitudinal Pattern Design

2021 ◽  
Vol 11 (13) ◽  
pp. 5760
Author(s):  
Sung-Yong Kim ◽  
Baek-Gyu Choi ◽  
Gwang-Won Oh ◽  
Chan-Jung Kim ◽  
Young-Seok Jung ◽  
...  
Keyword(s):  
Axial Load ◽  
Filler Content ◽  
Factor Model ◽  
Strain Sensor ◽  
Gauge Factor ◽  
Geometric Pattern ◽  
Pattern Design ◽  
Macro Scale ◽  
Composite Strain ◽  
Longitudinal Pattern

For an engineering feasibility study, we studied a simple design to improve NCSS (nanocarbon composite strain sensor) sensitivity by using its geometric pattern at a macro scale. We fabricated bulk- and grid-type sensors with different filler content weights (wt.%) and different sensor lengths and investigated their sensitivity characteristics. We also proposed a unit gauge factor model of NCSS to find a correlation between sensor length and its sensitivity. NCSS sensitivity was improved proportional to its length incremental ratio and we were able to achieve better linear and consistent data from the grid type than the bulk type one. We conclude that the longer sensor length results in a larger change of resistance due to its piezoresistive unit summation and that sensor geometric pattern design is one of the important issues for axial load and deformation measurement.

Behaviour of PLA/POSS nanocomposites: Effects of filler content, functional group and copolymer compatibilization

2021 ◽  
pp. 096739112110080
Author(s):  
Yelda Meyva Zeybek ◽  
Cevdet Kaynak
Keyword(s):  
Functional Group ◽  
Filler Content ◽  
Mechanical And Thermal Properties ◽  
Screw Extruder ◽  
Melt Mixing ◽  
Grafted Copolymer ◽  
Before And After ◽  
Twin Screw ◽  
Oligomeric Silsesquioxane ◽  
Matrix Nanocomposites

The main purpose of this study was to investigate influences of three parameters on the mechanical and thermal properties of the polylactide (PLA) matrix nanocomposites filled with polyhedral oligomeric silsesquioxane (POSS) particles. For the first parameter of “Filler Content”, nanocomposites with 1, 3, 5, 7 wt% basic POSS structure were compared. For the second parameter of “Functional Group,” basic POSS structure having only nonpolar isobutyl groups were compared with three other functionalized POSS structures; i.e. aminopropylisobutyl-POSS (ap-POSS), propanediolisobutyl-POSS (pd-POSS) and octasilane-POSS (os-POSS). Finally, for the third parameter of “Copolymer Compatibilization,” all specimens were compared before and after their maleic anhydride (MA) grafted copolymer compatibilization. Specimens were produced with twin-screw extruder melt mixing and shaped under compression molding. Various tests and analyses indicated that the optimum filler content for the improved mechanical properties was 1 wt%; while the optimum structure for strength and modulus was pd-POSS structure, in terms of fracture toughness it was basic POSS structure. Additional use of MA compatibilization was especially effective for the basic POSS and os-POSS particles.

Sign in / Sign up

Export Citation Format

Share Document