Early Mesozoic mantle-crust transitional zone in eastern Inner Mongolia: Evidence from measurements of compressional velocities of xenoliths at high pressure and high temperature

2000 ◽  
Vol 43 (S1) ◽  
pp. 253-261 ◽  
Author(s):  
Ji'an Shao ◽  
Qingjun Han
2020 ◽  
Author(s):  
Jianying Feng ◽  
Yu Zhang ◽  
Suping Wang

<p>In 2018, severe meteorological drought occurred in the southwest of Northeast China, the  east-central of Inner Mongolia and the east of North China. Drought shows obvious regional and stage nature .In early March, mild to moderate drought appeared in North China, followed by severe drought in parts of northern and eastern of Hebe province. After the middle of April, the drought was alleviated obviously, and the drought in the southwest of Northeast China began to show signs. In  early May, there was mild to moderate drought in the central and eastern part of Inner Mongolia, and the drought in Northeast China developed. From June to early August, severe drought and above occurred in parts of Liaoning province , Inner Mongolia and North China. In mid-August, in addition to Liaoning province and North China, there were scattered light to moderate drought, drought relief in the northern China. In early September, the drought in North China increased and the range spread northward, and there were droughts of different degrees in the whole North China.In winter, there is only mild drought in North China.</p><p>The drought in this region has affected the agricultural production in different degrees. Spring sowing is blocked in the east of Inner Mongolia and the west of Northeast China, and high temperature in summer leads to the development of drought, corn and rice and other crops are adversely affected.</p><p>From spring to autumn, the precipitation in most parts of the drought disaster  area is less than 10-40%, and the temperature is higher than 1-2 ℃. The lack of precipitation and abnormal high temperature accelerated the loss of surface water, which resulted in the occurrence of drought in this area.</p><p>In spring of 2018, the middle and high latitudes are generally controlled by flat air flow, which is not conducive to the establishment of trough ridge, making the northern dry area lack of favorable precipitation conditions; in summer and autumn, the existence of Baikal Lake high-pressure ridge, resulting in circulation patterns that are not conducive to the precipitation conditions in the northern dry area. Among them, the obvious flat air flow in spring and the obvious high pressure ridge in summer are the main reasons for the outstanding drought in spring and summer in the northern arid area.</p>


1999 ◽  
Vol 44 (14) ◽  
pp. 1272-1279 ◽  
Author(s):  
Ji’an Shao ◽  
Qingjun Han ◽  
Luqiao Zhang ◽  
Baolei Mu

Author(s):  
E. F. Koch

Because of the extremely rigid lattice structure of diamond, generating new dislocations or moving existing dislocations in diamond by applying mechanical stress at ambient temperature is very difficult. Analysis of portions of diamonds deformed under bending stress at elevated temperature has shown that diamond deforms plastically under suitable conditions and that its primary slip systems are on the ﹛111﹜ planes. Plastic deformation in diamond is more commonly observed during the high temperature - high pressure sintering process used to make diamond compacts. The pressure and temperature conditions in the sintering presses are sufficiently high that many diamond grains in the sintered compact show deformed microtructures.In this report commercially available polycrystalline diamond discs for rock cutting applications were analyzed to study the deformation substructures in the diamond grains using transmission electron microscopy. An individual diamond particle can be plastically deformed in a high pressure apparatus at high temperature, but it is nearly impossible to prepare such a particle for TEM observation, since any medium in which the diamond is mounted wears away faster than the diamond during ion milling and the diamond is lost.


Alloy Digest ◽  
2019 ◽  
Vol 68 (11) ◽  

Abstract YSS YXM4 is a cobalt-alloyed molybdenum high-speed tool steel with resistance to abrasion, seizure, and deformation under high pressure. This datasheet provides information on composition, physical properties, and hardness. It also includes information on high temperature performance. Filing Code: TS-780. Producer or source: Hitachi Metals America, Ltd.


Sign in / Sign up

Export Citation Format

Share Document