scholarly journals Investigation on the material removal and surface roughness in ultraprecision machining of Al/B4C/50p metal matrix composites

2019 ◽  
Vol 105 (7-8) ◽  
pp. 2815-2831 ◽  
Author(s):  
Zhichao Niu ◽  
Kai Cheng
Keyword(s):  
Surface Roughness ◽  
Metal Matrix ◽  
Material Removal ◽  
Cutting Speed ◽  
Surface Generation ◽  
Precision Machining ◽  
Depth Of Cut ◽  
Matrix Composites ◽  
Ultraprecision Machining ◽  
Simulation Results

Abstract Metal matrix composites (MMCs) are increasingly applied in various engineering industries because of their distinct physical and mechanical properties. While the precision machining of MMCs is less understood due to their complex microstructure and poor machinability, a comprehensive scientific understanding on their machining mechanics and the associated surface generation mechanisms is of great importance particularly for industrial scale applications of MMCs. This paper presents a simulation and experimental-based holistic investigation on cutting mechanics, material removal and surface roughness in ultraprecision machining of MMCs. B4C/Al2024 is selected as the targeted MMC material in this research. The thermal-mechanical-tribological integrated modelling and analysis are presented to investigate the effects of cutting speed, feed rate and depth of cut (DOC) on the material removal, chip formation mechanics and surface generation process. The simulation results indicate that the machined surface roughness in precision machining of particle reinforced MMCs can be reduced by increasing the cutting speed and decreasing the depth of cut. The surface flow waviness decreases, which contributes to a higher surface quality, while machining with a smaller feed rate. The well-designed machining trials are conducted under the same cutting conditions and process variables as those in simulations, which perform a good agreement with simulation results.

Effect of SiCp Reinforcement on Machinability of A356 Alloy Metal Matrix Composites

2016 ◽  
Vol 852 ◽  
pp. 142-148
Author(s):  
K. Jayakumar
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
End Milling ◽  
Cutting Speed ◽  
A356 Alloy ◽  
Experimental Result ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Matrix Composites

Machining of Aluminum Metal Matrix Composites (AMMCs) is a challenge for manufacturing industries due to their heterogeneous constituents which vary from soft matrix to hard reinforcements and their interfaces. To overcome the difficulties in machining of MMCs, researchers are continuously working to find the optimum process or machining parameters. In this work, End milling studies were carried out in A356 alloy powder-SiC particles (1 μm) in 0, 5, 10, 15 volume % reinforced AMMCs synthesised by vacuum hot pressing (VHP) route.The influence of machining parameters such as cutting speed, feed and depth of cut on the prepared composites in terms of surface roughness (Ra) and material removal rate (MRR) are measured from experimental study. Experiments were conducted as per Taguchi L16 orthogonal array with 4 factors and 4 levels.From the experimental result, it was identified that surface roughness varied from 0.214 μm to 4.115 μm and MRR varied from minimum of 1.11 cm3/min to maximum of 9.65 cm3/min. It is also observed that, MRR increased with increase in machining parameters and reinforcement quantity. Similarly, surface roughness decreased for increase of cutting speed, SiC particle (SiCp) reinforcement and increased for increase in feed and depth of cut. The optimum condition were observed in higher speed, lower feed and higher depth of cut on MMC with higher SiC content (15%) for getting higher machinability.

Effects of Process Parameters on Surface Roughness and MRR in the hard turning of EN 36 steel

2018 ◽  
pp. 102-110
Author(s):  
Amritpal Singh ◽  
Rakesh Kumar
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Hard Turning ◽  
Control Parameter ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Dry Cutting

In the present study, Experimental investigation of the effects of various cutting parameters on the response parameters in the hard turning of EN36 steel under the dry cutting condition is done. The input control parameters selected for the present work was the cutting speed, feed and depth of cut. The objective of the present work is to minimize the surface roughness to obtain better surface finish and maximization of material removal rate for better productivity. The design of experiments was done with the help of Taguchi L9 orthogonal array. Analysis of variance (ANOVA) was used to find out the significance of the input parameters on the response parameters. Percentage contribution for each control parameter was calculated using ANOVA with 95 % confidence value. From results, it was observed that feed is the most significant factor for surface roughness and the depth of cut is the most significant control parameter for Material removal rate.

Statistical Analysis of Process Parameters in Drilling of Al/Al2O3p Metal Matrix Composites

2014 ◽  
Vol 14 (3) ◽  
pp. 171-175 ◽  
Author(s):  
Yashvir Singh ◽  
Amneesh Singla ◽  
Ajay Kumar
Keyword(s):  
Surface Roughness ◽  
Statistical Analysis ◽  
Process Parameters ◽  
Metal Matrix ◽  
Design Method ◽  
Experimental Studies ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Signal To Noise ◽  
Drilling Parameters

AbstractThis paper presents a statistical analysis of process parameters for surface roughness in drilling of Al/Al2O3p metal matrix composite. The experimental studies were conducted under varying spindle speed, feed rate, point angle of drill. The settings of drilling parameters were determined by using Taguchi experimental design method. The level of importance of the drilling parameters is determined by using analysis of variance. The optimum drilling parameter combination was obtained by using the analysis of signal-to-noise ratio. Through statistical analysis of response variables and signal-to-noise ratios, the determined significant factors are depth of cut and drill point angle with the contributions of 87% and 12% respectively, whereas the cutting speed is insignificant contributing by 1% only. Confirmation tests verified that the selected optimal combination of process parameter through Taguchi design was able to achieve desired surface roughness.

Effect of machining parameters on the surface finish of a metal matrix composite under dry cutting conditions

2015 ◽  
Vol 231 (6) ◽  
pp. 913-923 ◽  
Author(s):  
Brian Boswell ◽  
Mohammad Nazrul Islam ◽  
Ian J Davies ◽  
Alokesh Pramanik
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composite ◽  
Tool Life ◽  
Surface Finish ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Dry Cutting

The machining of aerospace materials, such as metal matrix composites, introduces an additional challenge compared with traditional machining operations because of the presence of a reinforcement phase (e.g. ceramic particles or whiskers). This reinforcement phase decreases the thermal conductivity of the workpiece, thus, increasing the tool interface temperature and, consequently, reducing the tool life. Determining the optimum machining parameters is vital to maximising tool life and producing parts with the desired quality. By measuring the surface finish, the authors investigated the influence that the three major cutting parameters (cutting speed (50–150 m/min), feed rate (0.10–0.30 mm/rev) and depth of cut (1.0–2.0 mm)) have on tool life. End milling of a boron carbide particle-reinforced aluminium alloy was conducted under dry cutting conditions. The main result showed that contrary to the expectations for traditional machined alloys, the surface finish of the metal matrix composite examined in this work generally improved with increasing feed rate. The resulting surface roughness (arithmetic average) varied between 1.15 and 5.64 μm, with the minimum surface roughness achieved with the machining conditions of a cutting speed of 100 m/min, feed rate of 0.30 mm/rev and depth of cut of 1.0 mm. Another important result was the presence of surface microcracks in all specimens examined by electron microscopy irrespective of the machining condition or surface roughness.

A Comparison of Dry and Wet Machining of SiC Particle-Reinforced Aluminum Metal Matrix Composites

2012 ◽  
Vol 500 ◽  
pp. 168-173 ◽  
Author(s):  
Jian Guang Li ◽  
Jin Guang Du ◽  
Ying Xue Yao
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composites ◽  
Metal Matrix ◽  
Material Removal ◽  
Grinding Force ◽  
Matrix Composites ◽  
Dry Machining ◽  
Aluminum Metal ◽  
Aluminum Metal Matrix Composites ◽  
Sic Particle

This paper explains and demonstrates the machinability of dry and wet machining of SiC particle-reinforced aluminum metal matrix composites based on the experiments. The plunge surface experiments with mill-grinding method under wheel peripheral speed of up to 14.13m/s, feed rate 80mm/min and depth of cutting 50μm were carried out on a vertical CNC milling machine. The comparisons of dry and wet machining on the force composites and surface roughness (Ra) versus material removal volume were studied. The material removal volume was gained with the same machining parameters after an equal period of time. In most cases, the tangential mill-grinding force values are greater in wet machining condition than that in dry condition. But for normal mill-grinding force, the Fn values are much greater in dry machining condition than that in wet condition. And the normal mill-grinding force in wet machining increased quickly with increasing material removal volume. A better surface finish can be produced in dry machining than that produced by wet machining. The surface roughness decreased slowly with the increasing material removal volume and the surface roughness shows an insignificant decreasing trend in wet machining.

Study on Surface Roughness of Milling In-Situ TiB2 Particle Reinforced Al Matrix Composites

2019 ◽  
Author(s):  
Xiao-fen Liu ◽  
Wen-hu Wang ◽  
Rui-song Jiang ◽  
Yi-feng Xiong ◽  
Kun-yang Lin ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Matrix Composites ◽  
Cutting Depth

Abstract The current state of surface roughness focuses on the 2D roughness. However, there are shortcomings in evaluating surface quality of particle reinforced metal matrix composites using 2D roughness due to the fact that the measuring direction has a vital impact on the 2D roughness value. It is therefore of great importance and significance to develop a proper criterion for measuring and evaluating the surface roughness of cutting particle reinforced metal matrix composites. In this paper, an experimental investigation was performed on the effect of cutting parameters on the surface roughness in cutting in-situ TiB2/7050Al MMCs. The 2D roughness Ra, 3D roughness Sa and Sq were comparatively studied for evaluating the machined surface quality of in-situ TiB2/7050Al MMCs. The influence of cutting parameters on the surface roughness was also analyzed. The big difference between roughness Ra measured along cutting and feed directions showed the great impact of measuring direction. Besides, surface defects such as pits, grooves, protuberances and voids were observed, which would influence 2D roughness value greatly, indicating that 3D roughness was more suitable for evaluating surface quality of cutting in-situ TiB2/7050Al MMCs. The cutting depth and feed rate were found to have the highest influence on 3D roughness while the effect of cutting speed was minimal. With increasing feed rate, cutting depth or width, the 3D roughness increased accordingly. But it decreased as cutting speed increased.

Laser-Assisted Machining of a Fiber Reinforced Metal Matrix Composite

2010 ◽  
Vol 132 (6) ◽  
Author(s):  
Chinmaya R. Dandekar ◽  
Yung C. Shin
Keyword(s):  
Tool Wear ◽  
Metal Matrix ◽  
Material Removal ◽  
Volume Fraction ◽  
Cutting Speed ◽  
Subsurface Damage ◽  
Matrix Composites ◽  
Specific Cutting Energy ◽  
Laser Assisted Machining ◽  
Cutting Energy

Metal matrix composites, due to their excellent properties of high specific strength, fracture resistance, and corrosion resistance, are highly sought after over their nonferrous alloys, but these materials also present difficulty in machining. Excessive tool wear and high tooling costs of diamond tools make the cost associated with machining of these composites very high. This paper is concerned with the machining of high volume fraction long-fiber metal matrix composites (MMCs), which has seldom been studied. The composite material considered for this study is an Al–2% Cu aluminum matrix composite reinforced with 62% by volume fraction alumina fibers (Al–2% Cu/Al2O3). Laser-assisted machining (LAM) is utilized to improve the tool life and the material removal rate while minimizing the subsurface damage. The effectiveness of the laser-assisted machining process is studied by measuring the cutting forces, specific cutting energy, surface roughness, subsurface damage, and tool wear under various material removal temperatures. A multiphase finite element model is developed in ABAQUS/STANDARD to assist in the selection of cutting parameters such as tool rake angle, cutting speed, and material removal temperature. The multiphase model is also successful in predicting the damage depth on machining. The optimum material removal temperature is established as 300°C at a cutting speed of 30 m/min. LAM provides a 65% reduction in the surface roughness, specific cutting energy, tool wear rate, and minimum subsurface damage over conventional machining using the same cutting conditions.

Optimization of tungsten carbide processing parameters for laser heating and ultrasonic vibration composite assisted cutting

2018 ◽  
Vol 233 (12) ◽  
pp. 4140-4153
Author(s):  
Feng Jiao ◽  
Ming-jun Zhang ◽  
Ying Niu
Keyword(s):  
Surface Roughness ◽  
Tungsten Carbide ◽  
Ultrasonic Vibration ◽  
Laser Heating ◽  
Material Removal ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Machining Properties

Laser heating assisted cutting is a lucrative technique for machining difficult-to-machine materials such as tungsten carbide (YG20), which uses a high power laser to focally heat a workpiece before the material removal with traditional or innovative cutting tool. In the latter case, the application of ultrasonic vibration to the cutting edge was found to replace the continuous cutting mode to the interrupted one, it reduces the adhesion and entanglement of chips, improves the tool wear and surface roughness of the workpiece. The combination of laser heating assisted cutting and two-dimensional ultrasonic vibration cutting methods has been successfully applied by the authors of this paper for cutting of tungsten carbide (YG20). In this follow-up study, the proposed composite method is experimentally and theoretically verified. Through the mathematical model and simulation analysis, its advantages, including small cutting force, softening the effect and improved machining properties of the processed material (YG20) are corroborated. The dependencies between the laser power, cutting speed, depth of cut, and feed rate on the surface roughness are established via the response surface methodology. The genetic algorithm is applied to the optimization of machining parameters by setting the material removal rate as the object variable and surface roughness as a constraint variable. The results obtained strongly suggest that the optimized parameters improve the processing efficiency and furnish the required processing quality.

Sign in / Sign up

Export Citation Format

Share Document