scholarly journals An analysis of surface breakup induced by laser-generated cavitation bubbles in a turbulent liquid jet

2020 ◽  
Vol 61 (12) ◽  
Author(s):  
Jiayi Zhou ◽  
Mats Andersson
Keyword(s):  
Surface Tension ◽  
High Speed ◽  
Surface Deformation ◽  
Bubble Formation ◽  
Injection Pressure ◽  
Lower Surface ◽  
Video Camera ◽  
Liquid Jets ◽  
Water Mixture ◽  
Cavitation Bubbles

Abstract The breakup of turbulent liquid jets by cavitation bubbles was investigated by artificially introducing them by focusing laser light into the jet. The induced surface deformations and ejected liquid structures were characterized using shadowgraphy with a high-speed video camera. The flow velocity of the liquid jets, which were ejected from a 6 mm nozzle, was varied by adjusting the injection pressure from 1 to 5 bar. Deionized water and a dipropylene glycol–water mixture were used to compare the breakup of liquid jets with different surface tension and viscosity. Surface deformation and breakup were found to occur in two stages. One was early breakup of liquid strings into tiny droplets. This was followed by the formation of a larger structure separating into ligaments and larger drops. Averaged time-resolved one-dimensional plots were introduced and implemented to analyze breakup statistically, to address the problem of shot-to-shot variations in the breakup due to the turbulent condition of the jets. Bubble-induced breakup could easily be distinguished from spontaneous breakup with this method. Both the position of bubble formation and the injection pressure had an influence on the scale of the breakup. The deformation of the jet surface was highly affected by shear. The structure of the deformation became less intact when the surface tension was lower. The sizes of the drops produced during the second stage of breakup were analyzed. The bubble-induced breakup produced smaller drops than the spontaneous breakup at lower injection pressure. As expected, lower surface tension favored droplet detachment and smaller sized drops. Graphic abstract

Experimental Investigation of Droplet Dynamics on Solid Surfaces: Spreading and Recoil Effects

2006 ◽  
Author(s):  
Kalpak P. Gatne ◽  
Milind A. Jog ◽  
Raj M. Manglik
Keyword(s):  
Surface Tension ◽  
High Speed ◽  
Lower Surface ◽  
Video Camera ◽  
Temporal Variations ◽  
Liquid Viscosity ◽  
Viscous Effects ◽  
Droplet Dynamics ◽  
Digital Video Camera ◽  
The Impact

A study of the normal impact of liquid droplets on a dry horizontal substrate is presented in this paper. The impact dynamics, spreading and recoil behavior are captured using a high-speed digital video camera at 2000 frames per second. A digital image processing software was used to determine the drop spread and height of the liquid on the surface from each frame. To ascertain the effects of liquid viscosity and surface tension, experiments were conducted with four liquids (water, ethanol, propylene glycol and glycerin) that have vastly different fluid properties. Three different Weber numbers (20, 40, and 80) were considered by altering the height from which the drop is released. The high-speed photographs of impact, spreading and recoil are shown and the temporal variations of dimensionless drop spread and height are provided in the paper. The results show that changes in liquid viscosity and surface tension significantly affect the spreading and recoil behavior. For a fixed Weber number, lower surface tension promotes greater spreading and higher viscosity dampens spreading and recoil. Using a simple scale analysis of energy balance, it was found that the maximum spread factor varies as Re1/5 when liquid viscosity is high and viscous effects govern the spreading behavior.

Air Bubble Injection Into a Liquid Stream in a Minichannel

2013 ◽  
Author(s):  
Randy Samaroo ◽  
Masahiro Kawaji
Keyword(s):  
High Speed ◽  
Liquid Velocity ◽  
Bubble Formation ◽  
Video Camera ◽  
Velocity Profiles ◽  
Bubble Behavior ◽  
Particle Image Velocimetry Technique ◽  
Air Bubble ◽  
Cfd Models ◽  
Laminar And Turbulent Flow

Air bubble injection experiments have been performed to obtain a better understanding and detailed data on bubble behavior and liquid velocity profiles to be used for validation of 3-D Interface Tracking Models and CFD models. Two test sections used were vertical rectangular minichannels with a width and gap of 20 mm × 5.1 mm and 20 mm × 1.9 mm, respectively. Subcooled water at near atmospheric pressure flowed upward under laminar and turbulent flow conditions accompanied by air bubbles injected from a small hole on one of the vertical walls. The experiments yielded data on bubble formation and departure, and interactions with laminar or turbulent water flow. Instantaneous and ensemble-average liquid velocity profiles have been obtained using a Particle Image Velocimetry technique and a high speed video camera.

Experimental Investigation of Low Weber Number Post-Impact Drop Spreading on Solid Substrates

2010 ◽  
Author(s):  
Milind A. Jog ◽  
Raj M. Manglik
Keyword(s):  
Surface Tension ◽  
High Speed ◽  
Pure Water ◽  
Surfactant Solution ◽  
Video Camera ◽  
Dynamic Surface Tension ◽  
Temporal Variations ◽  
Dynamic Surface ◽  
Post Impact ◽  
Triton X

The post-impact spreading and recoil behaviors of droplets of pure liquids (water and ethanol) and aqueous solution of Triton X-100 (a surfactant) on a dry horizontal hydrophilic (glass) substrate are investigated for low Weber numbers. The evolution of drop shape during spreading and recoil are captured using a high-speed (4,000 frames per second) digital video camera. Digital image-processing was used to determine the spread and height of the liquid film on the surface from each frame. Unlike pure liquids, the liquid-gas interfacial tension for surfactant solution is a function of surface age, where surface tension is that of the solvent at zero time and then reaches an equilibrium value with increasing surface age. Furthermore, the equilibrium surface tension is a function of the surfactant concentration, which decreases from that of the solvent at zero concentration to that at the critical micelle concentration (CMC), and remains essentially constant thereafter. The surface tension of aqueous Triton X-100 solution varies from that of pure water to nearly that of ethanol. As such the comparison of transient droplet-impact-spreading-recoil behavior of the three liquids, or their temporal variations of the spread and the flattening factor, provides a basis for understanding the role of dynamic surface tension and surface wettability.

Bubble Detachment in Variable Gravity Under the Influence of Electric Fields

2002 ◽  
Author(s):  
Cila Herman ◽  
Shinan Chang ◽  
Estelle Iacona
Keyword(s):  
Electric Field ◽  
Electric Fields ◽  
High Speed ◽  
Bubble Formation ◽  
Experimental Studies ◽  
Video Camera ◽  
Contact Angles ◽  
Uniform Electric Field ◽  
Bubble Behavior ◽  
Insulating Liquid

The objective of the research is to investigate the behavior of individual air bubbles injected through an orifice into an electrically insulating liquid under the influence of a static electric field. Situations were considered with both uniform and nonuniform electric fields. Bubble formation and detachment were visualized in terrestrial gravity as well as for several levels of reduced gravity (lunar, martian and microgravity) using a high-speed video camera. Bubble volume, dimensions and contact angles at detachment were measured. In addition to the experimental studies, a simple model, predicting bubble characteristics at detachment in an initially uniform electric field was developed. The model, based on thermodynamic considerations, accounts for the level of gravity as well as the magnitude of the uniform electric field. The results of the study indicate that the level of gravity and the electric field magnitude significantly affect bubble behavior as well as shape, volume and dimensions.

Observation and Quantification of Gas Bubble Formation on a Mechanical Heart Valve

2000 ◽  
Vol 122 (4) ◽  
pp. 304-309 ◽  
Author(s):  
Hsin-Yi Lin ◽  
Brian A. Bianccucci ◽  
Steven Deutsch ◽  
Arnold A. Fontaine ◽  
J. M. Tarbell
Keyword(s):  
High Speed ◽  
Heart Valves ◽  
Bubble Formation ◽  
Mechanical Heart Valve ◽  
Gas Bubbles ◽  
Co2 Concentration ◽  
Video Camera ◽  
Gas Content ◽  
Gas Bubble ◽  
Cavitation Intensity

Clinical studies using transcranial Doppler ultrasonography in patients with mechanical heart valves (MHV) have detected gaseous emboli. The relationship of gaseous emboli release and cavitation on MHV has been a subject of debate in the literature. To study the influence of cavitation and gas content on the formation and growth of stable gas bubbles, a mock circulatory loop, which employed a Medtronic-Hall pyrolytic carbon disk valve in the mitral position, was used. A high-speed video camera allowed observation of cavitation and gas bubble release on the inflow valve surfaces as a function of cavitation intensity and carbon dioxide CO2 concentration, while an ultrasonic monitoring system scanned the aortic outflow tract to quantify gas bubble production by calculating the gray scale levels of the images. In the absence of cavitation, no stable gas bubbles were formed. When gas bubbles were formed, they were first seen a few milliseconds after and in the vicinity of cavitation collapse. The volume of the gas bubbles detected in the aortic track increased with both increased CO2 and increased cavitation intensity. No correlation was observed between O2 concentration and bubble volume. We conclude that cavitation is an essential precursor to stable gas bubble formation, and CO2, the most soluble blood gas, is the major component of stable gas bubbles. [S0148-0731(00)00204-1]

Effects of Surface Tension on Drop Impact on a Horizontal Rotating Disk

2012 ◽  
Vol 268-270 ◽  
pp. 1084-1093
Author(s):  
Xiao Fang Yuan ◽  
Jing Yin Li ◽  
Bin Zhang
Keyword(s):  
Surface Tension ◽  
High Speed ◽  
Tangential Velocity ◽  
Rotating Disk ◽  
Lower Surface ◽  
Drop Impact ◽  
Experimental Results ◽  
Impact Processes ◽  
Lower Surface Tension ◽  
The Impact

The impact processes of water and ethanol drops on a rotating horizontal aluminum disk were recorded and analyzed using a high-speed digital camera together with an image analysis program. The angular velocities of the disk were altered to study the effect of surface tension of drops on drop impact processes. The experimental results show that a lower surface tension will result in a higher tangential spread factor and a lower receding rate during the receding stage, for the drop impinging and depositing on a rotating disk. In addition, a lower surface tension of the drop tends to promote the occurrence of splash. The experimental results further verify a proposed correlation of splash-deposition boundary for drops impinging on a rotating disk. Both drops, though they have a quite different surface tension, experience four stages, with two new stages different from those of drops impinging on stationary surfaces. Their tangential spreading factors both increase obviously with the tangential velocity at the impact point, while their radial spreading factors vary a little.

Air entrapment under an impacting drop

2003 ◽  
Vol 478 ◽  
pp. 125-134 ◽  
Author(s):  
S. T. THORODDSEN ◽  
T. G. ETOH ◽  
K. TAKEHARA
Keyword(s):  
Surface Tension ◽  
High Speed ◽  
Liquid Surface ◽  
Reynolds Numbers ◽  
Video Camera ◽  
Air Entrapment ◽  
Contraction Speed ◽  
High Speed Video Camera ◽  
Drop Impacts ◽  
Two Bubbles

When a drop impacts on a liquid surface it entraps a small amount of air under its centre as the two liquid surfaces meet. The contact occurs along a ring enclosing a thin disk of air. We use the next-generation ultra-high-speed video camera, capable of 1 million f.p.s. (Etoh et al. 2002), to study the dynamics of this air sheet as it contracts due to surface tension, to form a bubble or, more frequently, splits into two bubbles. During the contraction of the air disk an azimuthal undulation, resembling a pearl necklace, develops along its edge. The contraction speed of the sheet is accurately described by a balance between inertia and surface tension. The average initial thickness of the air sheet decreases with higher impact Reynolds numbers, becoming less than one micron. The total volume of air entrapped depends strongly on the bottom curvature of the drop at impact. A sheet of micro-bubbles is often observed along the original interface. Oguz–Prosperetti bubble rings are also observed. For low Weber numbers (We<20) a variety of other entrapment phenomena appear.

scholarly journals Thermofluid Characterization of Nanofluid Spray Cooling Combining Phase Doppler Interferometry with High-Speed Visualization and Time-Resolved IR Thermography

Energies ◽  
2020 ◽  
Vol 13 (22) ◽  
pp. 5864 ◽  
Author(s):  
Miguel Figueiredo ◽  
Guido Marseglia ◽  
Ana S. Moita ◽  
Miguel R. O. Panão ◽  
Ana P. C. Ribeiro ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Surface Tension ◽  
High Speed ◽  
Lower Surface ◽  
Spray Cooling ◽  
Time Resolved ◽  
Maximum Heat ◽  
Phase Doppler Interferometry ◽  
Wetted Area

Spray impingement on smooth and heated surfaces is a highly complex thermofluid phenomenon present in several engineering applications. The combination of phase Doppler interferometry, high-speed visualization, and time-resolved infrared thermography allows characterizing the heat transfer and fluid dynamics involved. Particular emphasis is given to the use of nanofluids in sprays due to their potential to enhance the heat transfer mechanisms. The results for low nanoparticle concentrations (up to 1 wt.%) show that the surfactant added to water, required to stabilize the nanofluids and minimize particle clustering, affects the spray’s main characteristics. Namely, the surfactant decreases the liquid surface tension leading to a larger wetted area and wettability, promoting heat transfer between the surface and the liquid film. However, since lower surface tension also tends to enhance splash near the edges of the wetted area, the gold nanospheres act to lessen such disturbances due to an increase of the solutions’ viscosity, thus increasing the heat flux removed from the spray slightly. The experimental results obtained from this work demonstrate that the maximum heat convection coefficients evaluated for the nanofluids can be 9.8% to 21.9% higher than those obtained with the base fluid and 11.5% to 38.8% higher when compared with those obtained with DI water.

Visualization of Supersonic Non-Newtonian Liquid Jets

2012 ◽  
Vol 187 ◽  
pp. 63-67
Author(s):  
Anirut Matthujak ◽  
Chaidet Kasamnimitporn ◽  
Wuttichai Sittiwong ◽  
Kulachate Pianthong
Keyword(s):  
High Speed ◽  
Ambient Air ◽  
Video Camera ◽  
Newtonian Liquid ◽  
Liquid Jets ◽  
Liquid Jet ◽  
Dynamic Behaviors ◽  
Penetration Distance ◽  
Jet Penetration ◽  
Jet Velocity

This paper describes the characteristics of supersonic non-Newtonian liquid jets injected in ambient air. The main focus is to visualize three types of time-independent non-Newtonian liquid jet and to describe their behaviors. Moreover, comparisons between their dynamic behaviors with Newtonian liquid jet are reported. The supersonic liquid jets are generated by impact driven method in a horizontal single-stage power gun. Jets have been visualized by the high speed digital video camera and shadowgraph method. Effects of different liquid types on the jet penetration distance, average jet velocity and other characteristics have been examined. From shadowgraph images, the unique dynamic behaviors of each non-Newtonian liquid jets are observed and found obviously different from that of the Newtonian liquid jet. The maximum average jet velocity of 1,802.18 m/s (Mach no. 5.30) has been obtained. The jet penetration distance and average velocity are significantly varied when the liquid types are different.

Bubble Dynamics Observed in a Gas-Liquid Venturi Flow

2011 ◽  
Author(s):  
Wataru Nishi ◽  
Masanori Nogami ◽  
Hiroyuki Takahira
Keyword(s):  
High Speed ◽  
Bubble Dynamics ◽  
Propagation Speed ◽  
Video Camera ◽  
Bubble Surface ◽  
Liquid Jets ◽  
Pressure Waves ◽  
Two Phase ◽  
Pressure Transducers ◽  
Two Bubbles

The present study deals with the experiments for the gas-liquid two-phase flow inside an acrylic Venturi tube using a high-speed video camera. Some interesting phenomena on the bubble dynamics are observed in the tube. First, the volume and surface oscillations of two interacting bubbles are observed in converging section of the tube when one bubble enters the throat. The volume oscillation of the bubble that enters the throat is caused by the detachment of the tip of the downstream surface of the bubble. The pressure wave irradiated from the bubble that enters the throat induces the volume and surface oscillations of the bubble that remains at the converging section. The parametric excitation is the reason for the surface oscillations. Second, the bubble deformations at the throat in a Venturi or a converging tube are investigated. The experiments show that two kinds of liquid jets are formed on the bubble surface; one is a forward jet that develops from the upstream surface to the downstream surface and the other is a counter jet in which the direction of the jet is opposite to the forward jet. It is shown that the counter jet occurs only when the distance between two bubbles in the throat is sufficiently short. The interactions between two bubbles cause the counter jet. It is also shown that the velocity of the forward jet becomes faster when the bubble is pinched off more upstream in the converging section. Finally, the propagations of the pressure waves are measured with pressure transducers. The impulsive pressure associated with the collapse of cavitation bubble cloud is measured when a bubble enters the throat of the tube. Also, the propagation speed of pressure waves is evaluated with the cross-correlation function. The results show that the propagation speed and damping of the pressure waves are dependent on the number density of bubbles at the downstream part in the tube.

Sign in / Sign up

Export Citation Format

Share Document