Co-firing preparation and properties of piezoelectric ceramic/structural ceramics layered composites

2021 ◽  
Author(s):  
Kan Bian ◽  
Xiuxiu Li ◽  
Yiping Wang ◽  
Xiongjie Li ◽  
Sheng Sun ◽  
...  
Keyword(s):  
Piezoelectric Ceramic ◽  
Layered Composites ◽  
Structural Ceramics

Determination of the transverse shear stress in layered composites

2020 ◽  
Vol 86 (2) ◽  
pp. 44-53
Author(s):  
Yu. I. Dudarkov ◽  
M. V. Limonin
Keyword(s):  
Shear Stress ◽  
Transverse Shear ◽  
Composite Beam ◽  
Layered Composite ◽  
Equivalent Model ◽  
Shear Stresses ◽  
Transverse Shear Stress ◽  
Layered Composites ◽  
Laminate Composites ◽  
Transverse Shear Stresses

An engineering approach to estimation of the transverse shear stresses in layered composites is developed. The technique is based on the well-known D. I. Zhuravsky equation for shear stresses in an isotropic beam upon transverse bending. In general, application of this equation to a composite beam is incorrect due to the heterogeneity of the composite structure. According to the proposed method, at the first stage of its implementation, a transition to the equivalent model of a homogeneous beam is made, for which the Zhuravsky formula is valid. The transition is carried out by changing the shape of the cross section of the beam, provided that the bending stiffness and generalized elastic modulus remain the same. The calculated shear stresses in the equivalent beam are then converted to the stress values in the original composite beam from the equilibrium condition. The main equations and definitions of the method as well as the analytical equation for estimation of the transverse shear stress in a composite beam are presented. The method is verified by comparing the analytical solution and the results of the numerical solution of the problem by finite element method (FEM). It is shown that laminate stacking sequence has a significant impact both on the character and on the value of the transverse shear stress distribution. The limits of the applicability of the developed technique attributed to the conditions of the validity of the hypothesis of straight normal are considered. It is noted that under this hypothesis the shear stresses do not depend on the layer shear modulus, which explains the absence of this parameter in the obtained equation. The classical theory of laminate composites is based on the similar assumptions, which gives ground to use this equation for an approximate estimation of the transverse shear stresses in in a layered composite package.

Passive Vibration Damping Materials: Piezoelectric Ceramic Composites for Vibration Damping Applications.

1995 ◽  
Author(s):  
Shoko Yoshikawa ◽  
R. Meyer ◽  
J. Witham ◽  
S. Y. Agadda ◽  
G. Lesieutre
Keyword(s):  
Piezoelectric Ceramic ◽  
Ceramic Composites ◽  
Vibration Damping ◽  
Damping Materials

Rate-Dependent Indentation Response of Structural Ceramics

2010 ◽  
Vol 93 (8) ◽  
pp. 2377-2383 ◽  
Author(s):  
Michael A. Klecka ◽  
Ghatu Subhash
Keyword(s):  
Structural Ceramics ◽  
Rate Dependent ◽  
Indentation Response

Design of a slender turning cutting tool via a vibration absorber equipped with piezoelectric ceramic

2021 ◽  
pp. 107754632110144
Author(s):  
Yiqing Yang ◽  
Haoyang Gao ◽  
Qiang Liu
Keyword(s):  
Piezoelectric Ceramic ◽  
Cutting Tool ◽  
Vibration Suppression ◽  
Equations Of Motion ◽  
Electrical Energy ◽  
Diameter Ratio ◽  
Vibration Absorber ◽  
Machined Surface ◽  
Structural Part ◽  
Machined Surface Roughness

Turning cutting tool with large length–diameter ratio has been essential when machining structural part with deep cavity and in-depth hole features. However, chatter vibration is apt to occur with the increase of tool overhang. A slender turning cutting tool with a length–diameter ratio of 7 is developed by using a vibration absorber equipped with piezoelectric ceramic. The vibration absorber has dual functions of vibration transfer to the absorber mass and vibration conversion to the electrical energy via the piezoelectric effect. Equations of motion are established considering the dual damping from the piezoelectric ceramic and rubber gasket. The equivalent damping of piezoelectric ceramic is derived, and the geometries are optimized to achieve optimal vibration suppression. The modal analysis demonstrates that the cutting tool with the vibration absorber can reach 80.1% magnitude reduction. Machining tests are carried out in the end. The machining acceleration and machined surface roughness validate the vibration suppression of the VA, and the output voltage by the piezoelectric ceramic demonstrates the ability of vibration sensing.

scholarly journals Effect of Irradiation on Ni-Inconel/Incoloy Heterostructures in Multimetallic Layered Composites

2021 ◽  
Vol 547 ◽  
pp. 152778
Author(s):  
Shiddartha Paul ◽  
Daniel Schwen ◽  
Michael P. Short ◽  
Kasra Momeni
Keyword(s):  
Layered Composites

scholarly journals Power-Generation Optimization Based on Piezoelectric Ceramic Deformation for Energy Harvesting Application with Renewable Energy

Energies ◽  
2021 ◽  
Vol 14 (8) ◽  
pp. 2171
Author(s):  
Hyeonsu Han ◽  
Junghyuk Ko
Keyword(s):  
Power Generation ◽  
Renewable Energy ◽  
Energy Harvesting ◽  
Piezoelectric Material ◽  
Lead Zirconate Titanate ◽  
Piezoelectric Ceramic ◽  
Piezoelectric Element ◽  
Piezoelectric Ceramics ◽  
Lead Zirconate ◽  
Piezoelectric Energy

Along with the increase in renewable energy, research on energy harvesting combined with piezoelectric energy is being conducted. However, it is difficult to predict the power generation of combined harvesting because there is no data on the power generation by a single piezoelectric material. Before predicting the corresponding power generation and efficiency, it is necessary to quantify the power generation by a single piezoelectric material alone. In this study, the generated power is measured based on three parameters (size of the piezoelectric ceramic, depth of compression, and speed of compression) that contribute to the deformation of a single PZT (Lead zirconate titanate)-based piezoelectric element. The generated power was analyzed by comparing with the corresponding parameters. The analysis results are as follows: (i) considering the difference between the size of the piezoelectric ceramic and the generated power, 20 mm was the most efficient piezoelectric ceramic size, (ii) considering the case of piezoelectric ceramics sized 14 mm, the generated power continued to increase with the increase in the compression depth of the piezoelectric ceramic, and (iii) For piezoelectric ceramics of all diameters, the longer the depth of deformation, the shorter the frequency, and depending on the depth of deformation, there is a specific frequency at which the charging power is maximum. Based on the findings of this study, PZT-based elements can be applied to cases that receive indirect force, including vibration energy and wave energy. In addition, the power generation of a PZT-based element can be predicted, and efficient conditions can be set for maximum power generation.

scholarly journals Influence of machining parameters on micro-motion platform displacement during grinding Al-Mg alloys workpiece assisted by two-dimensional low-frequency vibration

2021 ◽  
Vol 30 ◽  
pp. 2633366X2098530
Author(s):  
Shiyang Yu ◽  
Shijun Ji ◽  
Ji Zhao ◽  
Chao Zhang ◽  
Handa Dai
Keyword(s):  
Cutting Force ◽  
Piezoelectric Ceramic ◽  
Input Voltage ◽  
Orthogonal Test ◽  
Spindle Speed ◽  
Test Method ◽  
Influential Factor ◽  
Machining Parameters ◽  
Motion Platform ◽  
Micro Motion

The main factors affecting the displacement of micro-motion platform during the grinding process are spindle speed, cutting force, and piezoelectric ceramic input voltage model. This article, using the orthogonal test method, found a set of machining parameters which lead to less displacement deviation between practical test and theoretic analysis. First of all, single-factor experiments were carried out to study how spindle speed, cutting force, and piezoelectric ceramic input voltage model affect the experimental results, and then the orthogonal test was conducted. The experimental datum shows that voltage model was the most influential factor, followed by spindle speed and cutting force. The optimum combination of grinding parameters was obtained as spindle speed of 800 r/min, cutting force of 18 N, and voltage model radius of 12 µm. At this time, the average unit error of displacement of micro-motion platform was 9.13%.

Sign in / Sign up

Export Citation Format

Share Document