Effect of Biaxial Stretching on Thermal Properties, Shrinkage and Mechanical Properties of Poly (Lactic Acid) Films

2012 ◽  
Vol 21 (1) ◽  
pp. 303-311 ◽  
Author(s):  
Jyh-Horng Wu ◽  
Ming-Shien Yen ◽  
Chien-Pang Wu ◽  
Chia-Hao Li ◽  
M. C. Kuo
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Poly Lactic Acid ◽  
Biaxial Stretching

Influence of extrusion screw speed on the properties of halloysite nanotube impregnated polylactic acid nanocomposites

2021 ◽  
Vol 0 (0) ◽  
Author(s):  
Chaitra Venkatesh ◽  
Yuanyuan Chen ◽  
Zhi Cao ◽  
Shane Brennan ◽  
Ian Major ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Composite Films ◽  
Polymer Melt ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Screw Speed ◽  
Halloysite Nanotube ◽  
The Past

Abstract Poly (lactic acid)/halloysite nanotube (PLA/HNT) nanocomposites have been studied extensively over the past few years owing to the interesting properties of the polymer, PLA, and the nanoclay, HNT, individually and as composites. In this paper, the influence of the screw speed during extrusion was investigated and was found to have a significant impact on the mechanical and thermal performance of the extruded PLA/HNT nanocomposites. To determine the effect of screw speed on PLA/HNT nanocomposites, 5 and 10 wt% of HNTs were blended into the PLA matrix through compounding at screw speeds of 40, 80, and 140 rpm. Virgin PLA was compounded for comparison. The resultant polymer melt was quench cooled onto a calendar system to produce composite films which were assessed for mechanical, thermal, chemical, and surface properties. Results illustrate that in comparison to 40 and 80 rpm, the virgin PLA when compounded at 140 rpm, indicated a significant increase in the mechanical properties. The PLA/HNT 5 wt% nanocomposite compounded at 140 rpm showed significant improvement in the dispersion of HNTs in the PLA matrix which in turn enhanced the mechanical and thermal properties. This can be attributed to the increased melt shear at higher screw speeds.

scholarly journals Effect of Selected Commercial Plasticizers on Mechanical, Thermal, and Morphological Properties of Poly(3-hydroxybutyrate)/Poly(lactic acid)/Plasticizer Biodegradable Blends for Three-Dimensional (3D) Print

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 1893 ◽  
Author(s):  
Přemysl Menčík ◽  
Radek Přikryl ◽  
Ivana Stehnová ◽  
Veronika Melčová ◽  
Soňa Kontárová ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Modulated Differential Scanning Calorimetry ◽  
3D Print ◽  
3D Printed ◽  
Biodegradable Blends

This paper explores the influence of selected commercial plasticizers structure, which are based on esters of citric acid, on mechanical and thermal properties of Poly(3-hydroxybutyrate)/Poly(lactic acid)/Plasticizer biodegradable blends. These plasticizers were first tested with respect to their miscibility with Poly(3-hydroxybutyrate)/Poly(lactic acid) (PHB/PLA) blends using a kneading machine. PHB/PLA/plasticizer blends in the weight ratio (wt %) of 60/25/15 were then prepared by single screw and corotating meshing twin screw extruders in the form of filament for further three-dimensional (3D) printing. Mechanical, thermal properties, and shape stability (warping effect) of 3D printed products can be improved just by the addition of appropriate plasticizer to polymeric blend. The goal was to create new types of eco-friendly PHB/PLA/plasticizers blends and to highly improve the poor mechanical properties of neat PHB/PLA blends (with majority of PHB) by adding appropriate plasticizer. Mechanical properties of plasticized blends were then determined by the tensile test of 3D printed test samples (dogbones), as well as filaments. Measured elongation at break rapidly enhanced from 21% for neat non-plasticized PHB/PLA blends (reference) to 328% for best plasticized blends in the form of filament, and from 5% (reference) to 187% for plasticized blends in the form of printed dogbones. The plasticizing effect on blends was confirmed by Modulated Differential Scanning Calorimetry. The study of morphology was performed by the Scanning Electron Microscopy. Significant problem of plasticized blends used to be also plasticizer migration, therefore the diffusion of plasticizers from the blends after 15 days of exposition to 110 °C in the drying oven was investigated as their measured weight loss. Almost all of the used plasticizers showed meaningful positive softening effects, but the diffusion of plasticizers at 110 °C exposition was quite extensive. The determination of the degree of disintegration of selected plasticized blend when exposed to a laboratory-scale composting environment was executed to roughly check the “biodegradability”.

Crystallization behavior and mechanical properties of poly(lactic acid) complex fiber toughened by carbon nanotube nanocapsules

2017 ◽  
Vol 88 (14) ◽  
pp. 1616-1627 ◽  
Author(s):  
Shu-qiang Liu ◽  
Gai-hong Wu ◽  
Yun-chao Xiao ◽  
Hong-xia Guo ◽  
Fen-juan Shao
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Carbon Nanotube ◽  
Crystallization Behavior ◽  
Poly Lactic Acid ◽  
Acid Complex ◽  
Main Obstacle ◽  
Industrial Areas

Poly(lactic acid) (PLA) fiber, owing to its biocompatibility and biodegradability, could be widely used in many related industrial areas. However, high brittleness has been the main obstacle to expanding its applications. So in this paper, carbon nanotube (CNT) nanocapsules were designed to toughen PLA and further reported their effect on the crystallization behavior and mechanical properties of PLA complex fiber. These designed CNT nanocapsules successfully solved the agglomeration of CNTs within the PLA matrix as well as the compatibility issue. In addition, the morphological, mechanical, optical and thermal properties of PLA complex fibers were also studied. The addition of CNT nanocapsules obviously improved the crystallization behavior of PLA fiber. Furthermore, compared with pure PLA, the tensile strength of PLA complex fiber was enhanced by 30.62% and the elongation by 32.2%, so the designed CNT nanocapsules could be used as a toughener for PLA fiber. This research benefits the extension of PLA applications where toughness is an important factor.

Effects of Processing Parameters and Nanofillers on Mechanical and Thermal Properties and Morphology of Impact Modified Poly (lactic acid)

2013 ◽  
Vol 1499 ◽  
Author(s):  
Eda Acik ◽  
Ulku Yilmazer
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Impact Strength ◽  
Random Copolymer ◽  
Processing Parameters ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Injection Molded ◽  
The Impact

ABSTRACTTernary nanocomposites of poly (lactic acid) (PLA) were produced by melt blending with two types of elastomers and five types of organoclays to obtain improved mechanical properties such as tensile strength, modulus and impact strength. One of the elastomers is a random copolymer of ethylene and glycidyl methacrylate (E-GMA) and the other one is a random terpolymer of ethylene-butyl acrylate-maleic anhydride (E-BA-MAH). Organically modified montmorillonites (OMMT) were utilized as nanofillers. XRD, DSC, tensile and impact tests were done on the injection molded samples. FTIR, SEM and TEM analyses are still in progress. As preliminary results, thermal analysis showed that the addition of compatibilizers and organoclays does not have a distinct effect on the thermal properties of the composites, and no evidence of nucleation activity of compatibilizers or organoclays was found. For all types of organoclays, the nanocomposites produced with E-GMA exhibited better mechanical properties in comparison to nanocomposites containing E-BA-MAH, especially for the impact strength.

scholarly journals Effect of Different Compatibilizers on Injection-Molded Green Fiber-Reinforced Polymers Based on Poly(lactic acid)-Maleinized Linseed Oil System and Sheep Wool

Polymers ◽  
2019 ◽  
Vol 11 (9) ◽  
pp. 1514 ◽  
Author(s):  
Franciszek Pawlak ◽  
Miguel Aldas ◽  
Juan López-Martínez ◽  
María Dolores Samper
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Linseed Oil ◽  
Fiber Reinforced Polymers ◽  
Coupling Agents ◽  
Poly Lactic Acid ◽  
Original Material ◽  
Fiber Reinforced ◽  
Sheep Wool

A method to modify polymers is that of introducing fibers in a matrix to produce a fiber-reinforced polymer (FRP). Consequently, the aim of this work was to study the compatibility effect of four coupling agents on wool FRP properties, using poly(lactic acid) plasticized with maleinized linseed oil as polymer matrix. The content of wool assessed was 1 phr. The compatibilizers were (3-(2-aminoethylamino)propyl)-trimethoxysilane, trimethoxy (2-(7-oxabicyclo (4.1.0)hept-3-yl) ethyl) silane, tris(2-methoxyethoxy)(vinyl) silane and titanium (IV) (triethanolaminate)isopropoxide. Initially, wool was modified with coupling agents in an acetone/water (50/50) solution. Mechanical properties were evaluated by tensile and flexural properties, hardness by Shore D measurement and impact resistance by Charpy’s energy. Differential scanning calorimetry, dynamic thermo-mechanical analysis, and thermogravimetric analysis were conducted to evaluate the interaction among components and the effect of the coupling agents on the thermal properties of the original material. Color, wettability and scanning electron microscopy were used to describe physical and microstructural properties. Modification of fibers allows achieving improved mechanical properties and changes the thermal properties of the FRPs slightly. Coupling agent treatment helps to formulate PLA–MLO and sheep wool materials and to improve their performance, thereby creating a broader spectrum of applications for PLA maintaining the bio-based character of the material.

Thermal Properties of Poly(Lactic Acid) Modified Poly(3-Hydroxybutyrate-co-4-Hydroxbutyrate)

2016 ◽  
Vol 852 ◽  
pp. 677-685
Author(s):  
Mei Li ◽  
Zhi Qiang Li ◽  
Wei Shao
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Tensile Tests ◽  
Poly Lactic Acid ◽  
Flow Properties ◽  
Scanning Calorimetry ◽  
Melt Flow Rate ◽  
Elongation At Break ◽  
Good Flow

The thermal properties of poly (lactic acid)[PLA] modified poly (3 –hydroxybutyrate –co-4 -hydroxbutyrate) [P(3HB-co-4HB)], prepared by melt blending with different blending ratios were investigated by differential scanning calorimetry [DSC], thermogravimetry [TGA], melt flow rate [MFR] and tensile test measurements, and scanning electron microscopy [SEM]. The DSC tests showed that the glass transition temperature, Tg, of P(3HB-co-4HB) increased from-7°C to 56°C when mixed with 50% to 67% of PLA. A decrease in crystallization temperature, Tc, of P(3HB-co-4HB) broadened the melting interval. The MFR tests indicated the blends had good flow properties and the variation of the PLA content had little effect on the flow properties. The tensile tests showed that PLA improved the mechanical properties of P(3HB-co-4HB), including the tensile strength and elongation at break. The blends had the best mechanical properties when the percentage of PLA was 64%.

scholarly journals Printability, Mechanical and Thermal Properties of Poly(3-Hydroxybutyrate)-Poly(Lactic Acid)-Plasticizer Blends for Three-Dimensional (3D) Printing

Materials ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 4736 ◽  
Author(s):  
Soňa Kontárová ◽  
Radek Přikryl ◽  
Veronika Melčová ◽  
Přemysl Menčík ◽  
Matyáš Horálek ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Three Dimensional ◽  
Poly Lactic Acid ◽  
Mechanical And Thermal Properties ◽  
Screw Extruder ◽  
Modulated Differential Scanning Calorimetry ◽  
Fused Deposition ◽  
3D Printed

This paper investigates the effect of plasticizer structure on especially the printability and mechanical and thermal properties of poly(3-hydroxybutyrate)-poly(lactic acid)-plasticizer biodegradable blends. Three plasticizers, acetyl tris(2-ethylhexyl) citrate, tris(2-ethylhexyl) citrate, and poly(ethylene glycol)bis(2-ethylhexanoate), were first checked whether they were miscible with poly(3-hydroxybutyrate)-poly(lactic acid) (PHB-PLA) blends using a kneading machine. PHB-PLA-plasticizer blends of 60-25-15 (wt.%) were then prepared using a corotating meshing twin-screw extruder, and a single screw extruder was used for filament preparation for further three-dimensional (3D) fused deposition modeling (FDM) printing. These innovative eco-friendly PHB-PLA-plasticizer blends were created with a majority of PHB, and therefore, poor mechanical properties and thermal properties of neat PHB-PLA blends were improved by adding appropriate plasticizer. The plasticizer also influences the printability of blends, which was investigated, based on our new specific printability tests developed for the optimization of printing conditions (especially printing temperature). Three-dimensional printed test samples were used for heat deflection temperature measurements and Charpy and tensile-impact tests. Plasticizer migration was also investigated. The macrostructure of 3D printed samples was observed using an optical microscope to check the printing quality and printing conditions. Tensile tests of 3D printed samples (dogbones), as well as extruded filaments, showed that measured elongation at break raised, from 21% for non-plasticized PHB-PLA reference blends to 84% for some plasticized blends in the form of filaments and from 10% (reference) to 32% for plasticized blends in the form of printed dogbones. Measurements of thermal properties (using modulated differential scanning calorimetry and oscillation rheometry) also confirmed the plasticizing effect on blends. The thermal and mechanical properties of PHB-PLA blends were improved by the addition of appropriate plasticizer. In contrast, the printability of the PHB-PLA reference seems to be slightly better than the printability of the plasticized blends.

Thermal and Mechanical Properties of Mulch Film from Poly(Lactic Acid)/Expoxidized Natural Rubber Blends Filled with Rutile TiO2 as Fillers

2013 ◽  
Vol 844 ◽  
pp. 65-68
Author(s):  
Pranee Nuinu ◽  
Kittikorn Samosorn ◽  
Kittisak Srilatong ◽  
Siripa Tongbut ◽  
Sayant Saengsuwan
Keyword(s):  
Thin Film ◽  
Mechanical Properties ◽  
Thermal Stability ◽  
Lactic Acid ◽  
Thermal Properties ◽  
Natural Rubber ◽  
Decomposition Temperature ◽  
Poly Lactic Acid ◽  
Thermal And Mechanical Properties ◽  
Thermal Stability Of

The aim of this research was to reduce and improve the brittleness and thermal properties of poly lactic acid (PLA), respectively. Epoxidized natural rubber (ENR) was used to enhance the toughness and rutile titanium dioxide (R-TiO2) as filler was also incorporated to improve the thermal properties of the PLA. 10wt% ENR with epoxidation contents of 25 mol% (ENR25) and 50 mol% (ENR50) and various R-TiO2contents (0-10 phr)were compounded with PLA by using a twin-screw extruder at 155-165°C and a rotor speed of 40 rpm. The pellets of blends were then formed a thin film using a cast film extruder machine and cooled down under air flow. Thermal and mechanical properties and morphology of PLA/ENR/R-TiO2thin film were investigated. The crystallinity of PLA was found to increase with addition of ENR. The mechanical properties of thin film showed that the ENR50 enhanced the elongation but reduced the tensile strength of PLA with addition of R-TiO2at 5 and 10 phr, respectively. The TGA indicated that the addition of 10 phr R-TiO2increased in the decomposition temperature at 5% weight loss (Td5%) of PLA/ENR film. Thus the thermal stability of PLA/ENR50 was found to improve with addition of R-TiO2. From morphology study, the ENR50 phase showed a good dispersion in the PLA matrix. In conclusion, the addition of ENR and R-TiO2was found to enhance both toughness and thermal stability of PLA.

Sign in / Sign up

Export Citation Format

Share Document