scholarly journals Surface Energy of Food Contact Materials and Its Relation to Wheat Dough Adhesion

2021 ◽  
Author(s):  
Rita Laukemper ◽  
Thomas Becker ◽  
Mario Jekle
Keyword(s):  
Food Processing ◽  
Contact Time ◽  
Contact Materials ◽  
Texture Analyzer ◽  
Wheat Dough ◽  
Angle Measurements ◽  
High Adhesion ◽  
Strong Linear Correlation ◽  
Contact Angle Measurements ◽  
Baking Industry

AbstractThis study investigates the influence of the surface free energy (SFE) on the adhesion behaviour between wheat dough and bakery-relevant food processing surfaces. In doing so, the contact time and production-related changes of the adhesive and the adherend were taken into account. The adhesion measurements were conducted by means of previously developed methods (modified Chen/Hoseney, contact time measuring cell), whereby the force required for separating the dough from the surface after processing-relevant contact times was determined applying a texture analyzer. The SFE was determined by contact angle measurements. The SFE values for the examined materials are ranged between 5.5 ± 0.81 and 42.7 ± 0.88 mN/m. A strong linear correlation between the SFE of the bakery surfaces and their adhesion to dough could be determined after a certain contact time (≥ 1 min) (r = + 0.96 for surfaces with Sa > 20 μm; r = + 0.94 for surfaces with Sa < 20 μm). Bakery surfaces with energy values σsolid surface, total > 30 mN/m including a polar content indicated a strong interaction with wheat dough, which was confirmed by high adhesion values. Production-related changes to the processing surfaces showed a great impact on the adhesion behaviour: e.g. the abrasion of proofing cloths caused a higher amount of protruding fibres, which operate as a separating layer, resulting in a decrease of dough adhesion even after long contact times. The results in this study emphasize the importance of the SFE in the development of processing surfaces for the baking industry.

Nanostructured Polymer Brushes With Reversibly Changing Properties

2002 ◽  
Vol 727 ◽  
Author(s):  
Denys Usov ◽  
Manfred Stamm ◽  
Sergiy Minko ◽  
Christian Froeck ◽  
Andreas Scholl ◽  
...  
Keyword(s):  
Polymer Brushes ◽  
Phase Segregation ◽  
Water Contact ◽  
Angle Measurements ◽  
Nanostructured Polymer ◽  
Contact Angle Measurements ◽  
Vertical Segregation ◽  
Oxygen Plasma Etching ◽  
Grafting From ◽  
Photoemission Electron

AbstractWe investigated the interplay between different mechanisms of the lateral and vertical segregation in the synthesized via “grafting from” approach symmetric A/B (where A and B are poly(styrene-co-2,3,4,5,6-pentafluorostyrene) and poly(methylmethacrylate), respectively) polymer brushes upon exposure to different solvents. We used X-ray photoemission electron spectroscopy and microscopy (X-PEEM), AFM, water contact angle measurements, and oxygen plasma etching to study morphology of the brushes. The ripple morphology after toluene (nonselective solvent) revealed elongated lamellar-like domains of A and B polymers alternating across the surface. The dimple-A morphology consisting of round clusters of the polymer A was observed after acetone (selective solvent for B). The top layer was enriched with the polymer B showing that the brush underwent both the lateral and vertical phase segregation. A qualitative agreement with predictions of SCF theory was found.

Wrinkling Poly(trimethylene 2,5-Furanoate) Free-standing Films: Nanostructure Formation and Physical Properties

2020 ◽  
Author(s):  
Michelina Soccio ◽  
Nadia Lotti ◽  
Andrea Munari ◽  
Esther Rebollar ◽  
Daniel E Martínez-Tong
Keyword(s):  
Irradiation Time ◽  
Polymer Surface ◽  
Laser Source ◽  
Free Standing ◽  
Force Microscopy ◽  
Nanostructure Formation ◽  
Physicochemical Changes ◽  
Angle Measurements ◽  
Atomic Force ◽  
Contact Angle Measurements

<p>Nanostructured wrinkles were developed on fully bio-based poly(trimethylene furanoate) (PTF) films by using the technique of Laser Induced Periodic Surface Structures (LIPSS). We investigated the effect of irradiation time on wrinkle formation using an UV pulsed laser source, at a fluence of 8 mJ/cm2. It was found that the pulse range between 600 and 4800 pulses allowed formation of periodic nanometric ripples. The nanostructured surface was studied using a combined macro- and nanoscale approach. We evaluated possible physicochemical changes taking place on the polymer surface after irradiation by infrared spectroscopy, contact angle measurements and atomic force microscopy. The macroscopic physicochemical properties of PTF showed almost no changes after nanostructure formation, differently from the results previously found for the terephthalic counterparts, as poly(ethyleneterephthalate), PET, and poly(trimethyleneterephthalate), PTT. The surface mechanical properties of the nanostructured PTF were found to be improved, as evidenced by nanomechanical force spectroscopy measurements. In particular, an increased Young’s modulus and higher stiffness for the nanostructured sample were measured. <br></p>

scholarly journals Adhesion Studies during Generative Hybridization of Textile-Reinforced Thermoplastic Composites via Additive Manufacturing

Materials ◽  
2021 ◽  
Vol 14 (14) ◽  
pp. 3888
Author(s):  
Johanna Maier ◽  
Christian Vogel ◽  
Tobias Lebelt ◽  
Vinzenz Geske ◽  
Thomas Behnisch ◽  
...  
Keyword(s):  
Additive Manufacturing ◽  
Polyamide 6 ◽  
Thermoplastic Composites ◽  
Efficient Production ◽  
Angle Measurements ◽  
Small Series ◽  
Contact Angle Measurements ◽  
Static Tensile ◽  
Pre Treatment ◽  
Manufacturing Technologies

Generative hybridization enables the efficient production of lightweight structures by combining classic manufacturing processes with additive manufacturing technologies. This type of functionalization process allows components with high geometric complexity and high mechanical properties to be produced efficiently in small series without the need for additional molds. In this study, hybrid specimens were generated by additively depositing PA6 (polyamide 6) via fused layer modeling (FLM) onto continuous woven fiber GF/PA6 (glass fiber/polyamide 6) flat preforms. Specifically, the effects of surface pre-treatment and process-induced surface interactions were investigated using optical microscopy for contact angle measurements as well as laser profilometry and thermal analytics. The bonding characteristic at the interface was evaluated via quasi-static tensile pull-off tests. Results indicate that both the bond strength and corresponding failure type vary with pre-treatment settings and process parameters during generative hybridization. It is shown that both the base substrate temperature and the FLM nozzle distance have a significant influence on the adhesive tensile strength. In particular, it can be seen that surface activation by plasma can significantly improve the specific adhesion in generative hybridization.

scholarly journals Epoxy/alumina composite coating on welded steel 316L with excellent wear and anticorrosion properties

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Maryama Hammi ◽  
Younes Ziat ◽  
Zakaryaa Zarhri ◽  
Charaf Laghlimi ◽  
Abdelaziz Moutcine
Keyword(s):  
Electrochemical Behaviour ◽  
Sem Analysis ◽  
Water Contact ◽  
Welded Steel ◽  
Melted Zone ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Alumina Composite ◽  
The Cost ◽  
Good Contrast

AbstractThe main purpose of this study is to elaborate anticorrosive coatings for the welded steel 316L, since this later is widely used in industrial field. Hence, within this work we have studied the electrochemical behaviour of different zones of the welded steel 316 in 1 M HCl media. The macrography study of the welded steel has revealed the different areas with a good contrast. We have stated three different zones, namely; melted zone (MZ), heat affected zone (HAZ) and base metal zone (BM). Impedance studies on welded steel 316L were conducted in 1 M HCl solution, coating of Epoxy/Alumina composite was applied on different zones, in order to reveal the anti-corrosion efficiency in each zone. Scanning electron microscopy (SEM) analysis was undertaken in order to check how far the used coating in such aggressive media protects the studied zones and these findings were assessed by water contact angle measurements. The choice of this coating is based on the cost and the safety. We concluded that the Epoxy/Alumina composite has a good protecting effect regarding welded steel in aggressive media.

Wettability Determination by Equilibrium Contact Angle Measurements: Reservoir Rock- Connate Water System With Injection of CO2

2012 ◽  
Author(s):  
Narjes Shojaikaveh ◽  
Cas Berentsen ◽  
Susanne Eva Johanne Rudolph-Floter ◽  
Karl Heinz Wolf ◽  
William Richard Rossen
Keyword(s):  
Contact Angle ◽  
Water System ◽  
Reservoir Rock ◽  
Equilibrium Contact Angle ◽  
Connate Water ◽  
Angle Measurements ◽  
Contact Angle Measurements

Surface Wettability Enhances Osteoblast Adhesion on Silicon-Substituted Hydroxyapatite Thin Films

2007 ◽  
Vol 330-332 ◽  
pp. 877-880 ◽  
Author(s):  
E.S. Thian ◽  
J. Huang ◽  
Serena Best ◽  
Zoe H. Barber ◽  
William Bonfield
Keyword(s):  
Thin Films ◽  
Contact Angle ◽  
Actin Filaments ◽  
Culture Study ◽  
Cell Culture Study ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Osteoblast Adhesion ◽  
Lower Contact

Crystalline hydroxyapatite (HA) and 0.8 wt.% silicon-substituted HA (SiHA) thin films were produced using magnetron co-sputtering. These films were subjected to contact angle measurements and in vitro cell culture study using human osteoblast-like (HOB) cells. A wettability study showed that SiHA has a lower contact angle, and thus is more hydrophilic in nature, as compared to HA. Consequently, enhanced cell growth was observed on SiHA at all time-points. Furthermore, distinct and well-developed actin filaments could be seen within HOB cells on SiHA. Thus, this work demonstrated that the surface properties of the coating may be modified by the substitution of Si into the HA structure.

scholarly journals PLA-Based Hybrid and Composite Electrospun Fibrous Scaffolds as Potential Materials for Tissue Engineering

2017 ◽  
Vol 2017 ◽  
pp. 1-11 ◽  
Author(s):  
Anna Magiera ◽  
Jarosław Markowski ◽  
Elzbieta Menaszek ◽  
Jan Pilch ◽  
Stanislaw Blazewicz
Keyword(s):  
Tissue Engineering ◽  
Mechanical Tests ◽  
Hybrid Structures ◽  
Poly Lactic Acid ◽  
Electrospinning Technique ◽  
Water Contact ◽  
Human Osteoblasts ◽  
Angle Measurements ◽  
Contact Angle Measurements ◽  
Normal Human

The aim of the study was to manufacture poly(lactic acid)- (PLA-) based nanofibrous nonwovens that were modified using two types of modifiers, namely, gelatin- (GEL-) based nanofibres and carbon nanotubes (CNT). Hybrid nonwovens consisting of PLA and GEL nanofibres (PLA/GEL), as well as CNT-modified PLA nanofibres with GEL nanofibres (PLA + CNT/GEL), in the form of mats, were manufactured using concurrent-electrospinning technique (co-ES). The ability of such hybrid structures as potential scaffolds for tissue engineering was studied. Both types of hybrid samples and one-component PLA and CNTs-modified PLA mats were investigated using scanning electron microscopy (SEM), water contact angle measurements, and biological and mechanical tests. The morphology, microstructure, and selected properties of the materials were analyzed. Biocompatibility and bioactivity in contact with normal human osteoblasts (NHOst) were studied. The coelectrospun PLA and GEL nanofibres retained their structures in hybrid samples. Both types of hybrid nonwovens were not cytotoxic and showed better osteoinductivity in comparison to scaffolds made from pure PLA. These samples also showed significantly reduced hydrophobicity compared to one-component PLA nonwovens. The CNT-contained PLA nanofibres improved mechanical properties of hybrid samples and such a 3D system appears to be interesting for potential application as a tissue engineering scaffold.

Sign in / Sign up

Export Citation Format

Share Document