Mechanical Properties and Formability of Heat-Treated 7000-Series High-Strength Aluminum Alloy: Experiments and Finite Element Modeling

2019 ◽  
Vol 26 (5) ◽  
pp. 682-694 ◽  
Author(s):  
Jinwoo Lee ◽  
Hyuk Jong Bong ◽  
Daeyong Kim ◽  
Young-Seon Lee ◽  
Yumi Choi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Aluminum Alloy ◽  
Finite Element Modeling ◽  
High Strength ◽  
High Strength Aluminum Alloy ◽  
Element Modeling ◽  
Heat Treated

Investigation of the joinability of the high-strength aluminum alloy AA7075 in shear-clinching processes

2021 ◽  
pp. 146442072110679
Author(s):  
S Wiesenmayer ◽  
M Merklein
Keyword(s):  
Mechanical Properties ◽  
Heat Treatment ◽  
Aluminum Alloy ◽  
High Strength ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
High Strength Aluminum Alloy ◽  
Heat Treated ◽  
Strength Alloy ◽  
Heating Up

Shear-clinching has proven to be a suitable technology for joining of high-strength materials. However, the mechanical properties of the upper joining partner are limited due to the high strains, which occur during the process. Therefore, shear-clinching of the high-strength aluminum alloy AA7075 in the T6 temper is not possible. Yet, the mechanical properties of hardenable alloys of the 7000 series can be influenced by a heat treatment. Thus, within the scope of this work, the joinability of the high-strength alloy AA7075 in shear-clinching processes in dependance of its temper is investigated. The as fabricated state F, the artificially aged T6 temper, a paint baked state and the naturally aged T4 temper are compared to the fully solution annealed W temper as well as to a retrogression heat-treated state. For retrogression heat treatment, a laser is used as heat source, heating up the alloy for a short term in order to only partially dissolve precipitations. The resulting mechanical properties are determined with uniaxial tensile tests. Moreover, the influence of the mechanical properties of AA7075 on the shear-clinching process, the joint formation and the resulting joint strength is analyzed.

scholarly journals Hardening of Nickel Alloys by Ion Implantation of Titanium and Carbon

1996 ◽  
Vol 444 ◽  
Author(s):  
S. M. Myers ◽  
D. M. Follstaedt ◽  
J. A. Knapp ◽  
T. R. Christenson
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Surface Layer ◽  
Ion Implantation ◽  
Finite Element Modeling ◽  
Yield Stress ◽  
Nickel Alloys ◽  
Element Modeling ◽  
Order Of Magnitude ◽  
Amorphous Surface

AbstractDual ion implantation of titanium and carbon was shown to produce an amorphous surface layer in annealed bulk nickel, in electroformed Ni, and in electroformed Ni7 5Fe 2 5. Diamond-tip nanoindentation coupled with finite-element modeling quantified the elastic and plastic mechanical properties of the implanted region. The amorphized matrix, with a thickness of about 100 nm, has a yield stress of approximately 6 GP and an intrinsic hardness near 16 GPa, exceeding by an order of magnitude the corresponding values for annealed bulk Ni. Implications for micro-electromechanical systems are discussed.

scholarly journals Evaluating Mechanical Properties of Thin Layers using Nanoindentation and Finite-Element Modeling: Implanted Metals and Deposited Layers

1996 ◽  
Vol 438 ◽  
Author(s):  
J. A. Knapp ◽  
D. M. Follstaedt ◽  
J. C. Barbour ◽  
S. M. Myers ◽  
J. W. Ager ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Finite Element Modeling ◽  
Yield Stress ◽  
Young’S Modulus ◽  
Layer Thickness ◽  
Young's Modulus ◽  
Thin Layers ◽  
Element Modeling ◽  
Surface Modified

AbstractWe present a methodology based on finite-element modeling of nanoindentation data to extract reliable and accurate mechanical properties from thin, hard films and surface-modified layers on softer substrates. The method deduces the yield stress, Young's modulus, and hardness from indentations as deep as 50% of the layer thickness.

Effect of In Situ TiB2 Particles on the Grain Size and Mechanical Properties of 7075 Aluminum Alloy

2021 ◽  
Vol 1035 ◽  
pp. 102-107
Author(s):  
Shao Ming Ma ◽  
Chuan Liu Wang ◽  
Yun Lin Fan
Keyword(s):  
Mechanical Properties ◽  
Grain Size ◽  
Aluminum Alloy ◽  
High Strength ◽  
Light Weight ◽  
7075 Aluminum Alloy ◽  
Directional Drilling ◽  
High Strength Aluminum Alloy ◽  
Drill Pipes

Light-weight and high-strength aluminum alloy drill pipes are potential and promising to replace traditional steel drill pipes. In this study, the grain size and mechanical properties of aluminum alloy drilling pipe materials reinforced by in-situ TiB2 particles were studied. The results showed when reinforced by in-situ TiB2 particles the grain size of aluminum alloy materials was refined from 155 m to 57 m and ultimate tensile strength was increased from 590 MPa to 720 MPa. Besides, the results also indicated that the friction coefficient was reduced from 0.99 to 0.50 and thus the abrasion resistance of 7075 aluminum alloy was enhanced by 34 %. This study provided theoretical basis for the application of light-weight and high-strength aluminum alloy drill pipes in directional drilling and ultra-deep wells.

The Study of Wrinkling Mechanism of Plasma-Treated Microphase-Separated Polyurethane Surface

2018 ◽  
Vol 773 ◽  
pp. 3-9 ◽  
Author(s):  
Ilya A. Morozov ◽  
Anton Y. Beliaev ◽  
Roman I. Izyumov
Keyword(s):  
Mechanical Properties ◽  
Finite Element ◽  
Elastic Modulus ◽  
Finite Element Modeling ◽  
Layer Surface ◽  
Element Modeling ◽  
Compression Deformation ◽  
Good Accordance ◽  
Nitrogen Ions ◽  
External Strain

Stiff coating on the phase-separated soft polyurethane substrate under the compression deformation is investigated by the finite element modeling (FEM). External strain leads to the wrinkling of layer surface, which is characterized by a set of wavelengths and amplitudes. The influence of the thickness and stiffness of the layer, elastic modulus of the substrate on the structural-mechanical properties of the deformed surface is studied. The results of the model are in good accordance with the experiment (plasma immersion ion impanation of nitrogen ions into the polyurethane substrate) and allowed to estimate the modulus of the coating and the deformation of the surface.

Sign in / Sign up

Export Citation Format

Share Document