scholarly journals Microstructure and mechanical properties of Zr3Al3C5-based ceramics synthesized by Al-Si melt infiltration

2021 ◽  
Vol 10 (3) ◽  
pp. 529-536
Author(s):  
Xiaomeng Fan ◽  
Yuzhao Ma ◽  
Yangfang Deng ◽  
Jinxue Ding ◽  
Laifei Cheng
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Phase Composition ◽  
Flexural Strength ◽  
Boundary Energy ◽  
Zirconium Carbide ◽  
Formation Temperature ◽  
Abnormal Growth ◽  
Microstructure And Mechanical Properties ◽  
Melt Infiltration

AbstractIn this work, bulk Zr3Al3C5-based ceramics were synthesized by the infiltration of Al-Si melt into zirconium carbide (ZrC) perform. The phase composition, microstructure, and mechanical properties of as-fabricated ceramics were studied. The results demonstrate that Si is more effective to reduce the twin boundary energy of ZrC than Al, and thus promotes the decrease of formation temperature of Zr3Al3C5. With the infiltration temperatures increasing from 1200 to 1500 °C, the Zr3Al3C5 content increases from 10 to 49 vol%, which is contributed to the increase of flexural strength from 62±9 to 222±10 MPa, and fracture toughness (KIC) from 2.8±0.2 to 4.1±0.3 MPa·m1/2. The decrease of mechanical properties for the samples fabricated at 1600 °C is ascribed to the abnormal growth of Zr3Al3C5 grains.

Effect of TiC Content on the Microstructure and Mechanical Properties of Ti3AlC2/Al2O3 In Situ Composites Synthesized by Hot Pressing

2012 ◽  
Vol 724 ◽  
pp. 278-281 ◽  
Author(s):  
Lan Ye ◽  
Jian Feng Zhu
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Phase Composition ◽  
Flexural Strength ◽  
High Temperatures ◽  
Vickers Hardness ◽  
Hot Pressing ◽  
Microstructure And Mechanical Properties ◽  
Reactive Hot Pressing

The Ti3AlC2/Al2O3 in situ composites were successfully synthesized from the system of Ti-TiC-Al-TiO2 by reactive hot pressing at 1350 °C. The effect of TiC content on the phase composition, microstructure and mechanical properties were investigated in detail. The results indicate that the fabricated products possess the highest purity as the TiC contents reduce to 90 % of its theoretical content. This deviation is mainly attributed to the decomposition of Ti3AlC2 and vaporization of Al at high temperatures. The effect of TiC content on the fracture toughness, flexural strength, Vickers hardness of Ti3AlC2/Al2O3 composites was also discussed in detail.

Effects of Sintering Additives on the Microstructure and Mechanical Properties of Silicon Nitride Ceramics by GPS

2010 ◽  
Vol 105-106 ◽  
pp. 27-30 ◽  
Author(s):  
Wei Ru Zhang ◽  
Feng Sun ◽  
Ting Yan Tian ◽  
Xiang Hong Teng ◽  
Min Chao Ru ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Phase Transformation ◽  
Silicon Nitride ◽  
Porous Silicon ◽  
Flexural Strength ◽  
Relative Density ◽  
Sintering Additives ◽  
Microstructure And Mechanical Properties ◽  
Nitride Ceramics

Silicon nitride ceramics were prepared by gas pressure sintering (GPS) with different sintering additives, including La2O3, Sm2O3 and Al2O3. Effect of sintering additives on the phase-transformation, microstructure and mechanical properties of porous silicon nitride ceramics was investigated. The results show that the reaction of sintering additives each other and with SiO2 had key effects on the phase-transformation, grain growing and grain boundaries. With 9MPa N2 atmosphere pressure, holding 1h at 1850°C, adding 10wt% one of the La2O3, Sm2O3, Al2O3, porous silicon nitride was prepared and the relative density was 78%, 72%, 85% respectively. The flexural strength was less than 500MPa, and the fracture toughness was less than 4.8MPam1/2. Dropping compounds sintering additives, such as La2O3+Al2O3, Sm2O3+Al2O3 effectively improves the sintering and mechanical properties. The relative density was 99.2% and 98.7% with 10wt% compounds sintering additives. The grain ratio of length to diameter was up to 1:8. The flexural strength was more than 900MPa, and the fracture toughness was more than 8.9MPam1/2.

scholarly journals Preparation and Performance of Al2O3/Ti(C,N)-Added ZrO2 Whisker and NanoCoated CaF2@Al(OH)3 Powder

2020 ◽  
Vol 10 (13) ◽  
pp. 4435
Author(s):  
Qi Li ◽  
Guangchun Xiao ◽  
Zhaoqiang Chen ◽  
Runxin Guo ◽  
Mingdong Yi ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Phase Transition ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Ceramic Material ◽  
Microstructure And Mechanical Properties ◽  
And Performance

The Al2O3/Ti(C,N) ceramic material added micron ZrO2 whisker and nano coated CaF2@Al(OH)3 powder was fabricated. The micron ZrO2 whisker was for the toughening and reinforcing phase and the nano coated CaF2@Al(OH)3 powder was the lubricant. For obtaining a ceramic material with optimal comprehensive mechanical properties and friction properties, the influences of different compositions of the ZrO2 whisker and nano coated CaF2@Al(OH)3 powder on the microstructure and mechanical properties were analyzed, respectively. The result demonstrated that as the addition of the ZrO2 whisker was 6 vol% and the addition of the nano coated CaF2@Al(OH)3 powder was 10 vol%, the optimal self-lubricating ceramic material had optimal mechanical properties. The hardness of the ceramic material was 16.72 GPa, the flexural strength was 520 MPa and the fracture toughness reached 7.16 MPa·m1/2. The formation of the intragranular structure, whisker toughening and the phase transition of ZrO2 were the main mechanisms.

Microstructure and Mechanical Properties of SiC Whisker-Reinforced ZrB2 Ultra-High Temperature Ceramic

2008 ◽  
Vol 368-372 ◽  
pp. 1730-1732 ◽  
Author(s):  
Ping Hu ◽  
Xing Hong Zhang ◽  
Jie Cai Han ◽  
Song He Meng ◽  
Bao Lin Wang
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
High Temperature ◽  
Flexural Strength ◽  
Hot Pressing ◽  
Room Temperature ◽  
Pressing Temperature ◽  
Sintering Time ◽  
Microstructure And Mechanical Properties ◽  
Ultra High Temperature

SiC whisker-reinforced ZrB2 matrix ultra-high temperature ceramic were prepared at 2000°C for 1 h under 30MPa by hot pressing and the effects of whisker on flexural strength and fracture toughness of the composites was examined. The flexural strength and fracture toughness are 510±25MPa and 4.05±0.20MPa⋅m1/2 at room temperature, respectively. Comparing with the SiC particles-reinforced ZrB2 ceramic, no significant increase in both strength and toughness was observed. The microstructure of the composite showed that the SiC whisker was destroyed because the SiC whisker degraded due to rapid atom diffusivity at high temperature. The results suggested that some related parameters such as the lower hot-pressing temperature, a short sintering time should be controlled in order to obtain SiC whiskerreinforced ZrB2 composite with high properties.

scholarly journals Microstructure and Mechanical Properties of ZrB2–HfC Ceramics Influenced by HfC Addition

Materials ◽  
2018 ◽  
Vol 11 (10) ◽  
pp. 2046 ◽  
Author(s):  
Yi Jing ◽  
Hongbing Yuan ◽  
Zisheng Lian
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Grain Boundaries ◽  
Sintering Temperature ◽  
Liquid Phase Sintering ◽  
Weak Interface ◽  
Interface Bonding ◽  
Microstructure And Mechanical Properties ◽  
Small Grains

ZrB2–HfC ceramics have been fabricated using the liquid phase sintering technique at a sintering temperature as low as 1750 °C through the addition of Ni. The effects of HfC addition on the microstructure and mechanical properties of ZrB2–based ceramics have been investigated. These ceramics were composed of ZrB2, HfC, Ni, and a small amount of possible (Zr, Hf)B2 solid solution. Small HfC grains were distributed among ZrB2 grain boundaries. These small grains could improve the density of ZrB2–based ceramics and play a pinning role. With HfC content increasing from 10 wt % to 30 wt %, more HfC grains were distributed among ZrB2 grain boundaries, leading to weaker interface bonding among HfC grains; the relative density and Vickers hardness increased, and flexural strength and fracture toughness decreased. The weak interface bonding for 20 and 30 wt % HfC contents was the main cause of the decrease in both flexural strength and fracture toughness.

Effect of Iron Additive on the Sintering Behavior of Hot-Pressed ZrC-W Composites

2008 ◽  
Vol 368-372 ◽  
pp. 1764-1766 ◽  
Author(s):  
Yu Jin Wang ◽  
Lei Chen ◽  
Tai Quan Zhang ◽  
Yu Zhou
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Relative Density ◽  
Sintering Temperature ◽  
Sintering Behavior ◽  
Hot Press ◽  
Sintering Additive ◽  
Microstructure And Mechanical Properties ◽  
Hot Press Sintering

The ZrC-W composites with iron as sintering additive were fabricated by hot-press sintering. The densification, microstructure and mechanical properties of the composites were investigated. The incorporation of Fe beneficially promotes the densification of ZrC-W composites. The relative density of the composite sintered at 1900°C can attain 95.3%. W2C phase is also found in the ZrC-W composite sintered at 1700°C. The content of W2C decreases with the increase of sintering temperature. However, W2C phase is not identified in the composite sintered at 1900°C. The flexural strength and fracture toughness of the composites are strongly dependent on sintering temperature. The flexural strength and fracture toughness of ZrC-W composite sintered at optimized temperature of 1800°C are 438 MPa and 3.99 MPa·m1/2, respectively.

Effects of Nano-ZrO2 on the Microstructure and Mechanical Properties of Ti(C,N)-Based Cermet Die Materials

2010 ◽  
Vol 154-155 ◽  
pp. 1319-1323 ◽  
Author(s):  
Xing Hai Wang ◽  
Chong Hai Xu ◽  
Ming Dong Yi ◽  
Hui Fa Zhang
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Electron Microscope ◽  
Flexural Strength ◽  
Weight Percent ◽  
Environmental Scanning ◽  
Microstructure And Mechanical Properties ◽  
Vacuum Atmosphere ◽  
Die Materials ◽  
Scanning Electron

In recent, the development of new die materials is one of the important topics in the field of die research. In this paper, effects of nano-ZrO2 addition on the microstructure and mechanical properties of Ti(C,N)-based cermets were studied. The newly developed Ti(C,N)-based cermet die materials with different contents of nano-ZrO2 of 0~25wt% were prepared by hot pressing technique under vacuum atmosphere at 1450°C for 30min. Moreover, the microstructure of this Ti(C,N)-based cermet die materials was observed by environmental scanning electron microscope. It indicates that the comprehensive mechanical properties can reach the optimum when the weight percent of the nano-ZrO2 is 10%. The corresponding flexural strength and fracture toughness is 967 MPa and 13.62 MPa•m1/2, respectively which is approximately 65% and 110% higher than that of the cermet without nano-ZrO2 addition. It suggests that the addition of nano-ZrO2 can improve the mechanical properties especially the fracture toughness and flexural strength of Ti(C,N)-based cermet die materials.

Microstructure and Mechanical Properties of Hot Pressed ZrC-SiC-ZrB2 Composites

2010 ◽  
Vol 434-435 ◽  
pp. 173-177 ◽  
Author(s):  
Bao Xia Ma ◽  
Wen Bo Han ◽  
Xing Hong Zhang
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Grain Size ◽  
Flexural Strength ◽  
Hot Pressing ◽  
Ceramic Composites ◽  
Strong Function ◽  
Slight Tendency ◽  
Microstructure And Mechanical Properties

Ternary ZrC-SiC-ZrB2 ceramic composites were prepared by hot pressing at 1900 °C for 60 min under a pressure of 30 MPa in argon. The influence of ZrB2 content on the microstructure and mechanical properties of ZrC-SiC-ZrB2 composites was investigated. Examination of SEM showed that the microstructure of the composites consisted of the equiaxed ZrB2, ZrC and SiC grains, and there was a slight tendency of reduction for grain size in ZrC with increasing ZrB2 content. The hardness increased considerably from 23.3 GPa for the ZS material to 26.4 GPa for the ZS20B material. Flexural strength was a strong function of ZrB2 content, increasing from 407 MPa without ZrB2 addition to 627 MPa when the ZrB2 content was 20vol.%. However, the addition of ZrB2 has little influence on the fracture toughness, ranging between 5.5 and 5.7 MPam1/2.

The Effects of MgO Content on the Mechanical Properties and Microstructures of Al2O3-TiN-TiC Ceramic Materials

2012 ◽  
Vol 500 ◽  
pp. 623-628 ◽  
Author(s):  
Yu Huan Fei ◽  
Chuan Zhen Huang ◽  
Han Lian Liu ◽  
Bin Zou
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Phase Composition ◽  
Flexural Strength ◽  
Crack Path ◽  
Ceramic Materials ◽  
Optical Microscope ◽  
Volume Percent ◽  
Sintered Ceramic ◽  
Microstructure Morphology

Al2O3-TiN-TiC ceramic materials with different MgO content were fabricated by hot-pressing technique. The MgO volume percent was varied from 0vol% to 5vol%. The mechanical properties such as flexural strength, Vickers hardness and fracture toughness were tested. The phase composition of the sintered body was analyzed by XRD while the microstures of the sintering body were observed by OM (Optical Microscope) and SEM. The effects of MgO content on the mechanical properties and microstructures of Al2O3-TiN-TiC were investigated. The results shows that the addition of MgO can change the phase composition of the sintered ceramic materials which displayed with diverse solid solutions and intermetallic compounds. Meanwhile the new sintering products changed the the microstructure morphology which made the crack path complex and affected the mechanical properties.

Effect of TiN Addition on Microstructure and Mechanical Properties of Zirconia Matrix Ceramic Tool Material

2004 ◽  
Vol 471-472 ◽  
pp. 321-325 ◽  
Author(s):  
Jing Sun ◽  
Chuan Zhen Huang ◽  
Han Lian Liu ◽  
Sui Lian Wang
Keyword(s):  
Mechanical Properties ◽  
Fracture Toughness ◽  
Flexural Strength ◽  
Monoclinic Phase ◽  
Tetragonal Zirconia ◽  
Tool Material ◽  
Strengthening Mechanisms ◽  
Microstructure And Mechanical Properties ◽  
Ceramic Tool Material ◽  
Tetragonal Zirconia Polycrystal

In this paper, 3mol% yttria-stabilized tetragonal zirconia polycrystal (3Y-TZP) and TiN/3Y-TZP(adding TiN particles to 3Y-TZP) composites were fabricated by hot-pressing technique. Phase composition, microstructure and mechanical properties of the composites were investigated. It is shown that the flexural strength, fracture toughness and Vickers hardness of TiN/3Y-TZP was significantly improved by the addition of TiN particles compared with 3Y-TZP. The flexural strength of ZYT2 (20wt% TiN addition) is 1318 MPa. The fracture toughness of ZYT4 (40wt% TiN addition) is 16.8MPa·m1/2. The toughening and strengthening mechanisms were analyzed. The XRD results show that the additing of TiN can hinder the transformation from tetragonal phase to monoclinic phase of 3Y-TZP during fabrication process.

Sign in / Sign up

Export Citation Format

Share Document