scholarly journals Fuzzy Identification and Delay Compensation based on the Force/Position Control Scheme of the 5-DOF Redundantly Actuated Parallel Robot

2016 ◽  
Vol 19 (1) ◽  
pp. 124-140 ◽  
Author(s):  
Shuhuan Wen ◽  
Haiyang Yu ◽  
Baowei Zhang ◽  
Yongsheng Zhao ◽  
H. K. Lam ◽  
...  
Keyword(s):  
Position Control ◽  
Parallel Robot ◽  
Delay Compensation ◽  
Fuzzy Identification ◽  
Control Scheme ◽  
Redundantly Actuated

scholarly journals Proposal of a Decoupled Structure of Fuzzy-PID Controllers Applied to the Position Control in a Planar CDPR

Electronics ◽  
2021 ◽  
Vol 10 (6) ◽  
pp. 745
Author(s):  
Marco Carpio ◽  
Roque Saltaren ◽  
Julio Viola ◽  
Cristian Calderon ◽  
Juan Guerra
Keyword(s):  
Position Control ◽  
Control Structure ◽  
Parallel Robot ◽  
Pid Controllers ◽  
Fuzzy Pid ◽  
End Effector ◽  
Robot Systems ◽  
Decoupled Control ◽  
The Mathematical Model ◽  
Decoupled Structure

The design of robot systems controlled by cables can be relatively difficult when it is approached from the mathematical model of the mechanism, considering that its approach involves non-linearities associated with different components, such as cables and pulleys. In this work, a simple and practical decoupled control structure proposal that requires practically no mathematical analysis was developed for the position control of a planar cable-driven parallel robot (CDPR). This structure was implemented using non-linear fuzzy PID and classic PID controllers, allowing performance comparisons to be established. For the development of this research, first the structure of the control system was proposed, based on an analysis of the cables involved in the movement of the end-effector (EE) of the robot when they act independently for each axis. Then a tuning of rules was carried out for fuzzy PID controllers, and Ziegler–Nichols tuning was applied to classic PID controllers. Finally, simulations were performed in MATLAB with the Simulink and Simscape tools. The results obtained allowed us to observe the effectiveness of the proposed structure, with noticeably better performance obtained from the fuzzy PID controllers.

Hybrid Control of the Berkeley Lower Extremity Exoskeleton (BLEEX)

2005 ◽  
Author(s):  
Lihua Huang ◽  
Ryan Ryan Steger ◽  
H. Kazerooni
Keyword(s):  
Position Control ◽  
Hybrid Control ◽  
System Sensitivity ◽  
Walking Gait ◽  
Mixed Control ◽  
Stance Control ◽  
Control Scheme ◽  
Load Carrying ◽  
Human Limb ◽  
Careful Design

The first functional load-carrying and energetically autonomous exoskeleton was demonstrated at U.C. Berkeley, walking at the average speed of 0.9 m/s (2 mph) while carrying a 34 kg (75 lb) payload. The original BLEEX sensitivity amplification controller, based on positive feedback, was designed to increase the closed loop system sensitivity to its wearer’s forces and torques without any direct measurement from the wearer. The controller was successful at allowing natural and unobstructed load support for the pilot. This article presents an improved control scheme we call “mixed” control that adds robustness to changing BLEEX backpack payload. The walking gait cycle is divided into stance control and swing control phases. Position control is used for the BLEEX stance leg (including torso and backpack) and the sensitivity amplification controller is used for the swing leg. The controller is also designed to smoothly transitions between these two schemes as the pilot walks. With mixed control, the controller does not require a good model of the BLEEX torso and payload, which is difficult to obtain and subject to change as payload is added and removed. As a tradeoff, the position control used in this method requires the human to wear seven inclinometers to measure human limb and torso angles. These additional sensors require careful design to securely fasten them to the human and increase the time to don (and doff) BLEEX.

scholarly journals Design and Experimental Evaluation of a Robust Position Controller for an Electrohydrostatic Actuator Using Adaptive Antiwindup Sliding Mode Scheme

2013 ◽  
Vol 2013 ◽  
pp. 1-16 ◽  
Author(s):  
Ji Min Lee ◽  
Sung Hwan Park ◽  
Jong Shik Kim
Keyword(s):  
Control Systems ◽  
Pid Controller ◽  
Position Control ◽  
Sliding Mode ◽  
System Modeling ◽  
Modeling Error ◽  
Load Disturbance ◽  
Control Scheme ◽  
Position Controller ◽  
System Uncertainties

A robust control scheme is proposed for the position control of the electrohydrostatic actuator (EHA) when considering hardware saturation, load disturbance, and lumped system uncertainties and nonlinearities. To reduce overshoot due to a saturation of electric motor and to realize robustness against load disturbance and lumped system uncertainties such as varying parameters and modeling error, this paper proposes an adaptive antiwindup PID sliding mode scheme as a robust position controller for the EHA system. An optimal PID controller and an optimal anti-windup PID controller are also designed to compare control performance. An EHA prototype is developed, carrying out system modeling and parameter identification in designing the position controller. The simply identified linear model serves as the basis for the design of the position controllers, while the robustness of the control systems is compared by experiments. The adaptive anti-windup PID sliding mode controller has been found to have the desired performance and become robust against hardware saturation, load disturbance, and lumped system uncertainties and nonlinearities.

Impedance Control of Dual-Arm Systems Based on the Object with Senseless Force

2013 ◽  
Vol 765-767 ◽  
pp. 1920-1923
Author(s):  
Li Jiang ◽  
Yang Zhou ◽  
Bin Wang ◽  
Chao Yu
Keyword(s):  
Numerical Simulations ◽  
Relative Position ◽  
Position Control ◽  
Impedance Control ◽  
Force Sensors ◽  
Operational Space ◽  
Novel Approach ◽  
Control Scheme ◽  
Statics And Dynamics ◽  
Dual Arm

A novel approach to impedance control based on the object is proposed to control dual-arm systems with senseless force. Considering the motion of the object, the statics and dynamics of the dual-arm systems are modeled. Extending the dynamics of dual-arm system and the impedance of object to the operational space, impedance control with senseless force is presented. Simulations on a dual-arm system are carried out to demonstrate the performance of the proposed control scheme. Comparing with position control, results of numerical simulations show that the proposed scheme realizes suitable compliant behaviors in terms of the object, and minimizes the error of the relative position between the manipulators even without force sensors.

Sign in / Sign up

Export Citation Format

Share Document