Design, development, fabrication and testing of low-cost, laser-engraved, embedded, nano-composite-based pressure sensor

2021 ◽  
Author(s):  
B. Pavithra ◽  
Smitha G. Prabhu ◽  
M. Manjunatha Nayak
Keyword(s):  
Pressure Sensor ◽  
Low Cost ◽  
Design Development ◽  
Nano Composite

Design, Development and Application of Vehicle Gas Turbine Engines

1966 ◽  
Vol 181 (1) ◽  
pp. 149-172
Author(s):  
P. A. Phillips ◽  
Peter Spear
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Low Cost ◽  
Engine Performance ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Design Development ◽  
Turbine Engine ◽  
Wide Range ◽  
Cycle Temperature

After briefly summarizing worldwide automotive gas turbine activity, the paper analyses the power plant requirements of a wide range of vehicle applications in order to formulate the design criteria for acceptable vehicle gas turbines. Ample data are available on the thermodynamic merits of various gas turbine cycles; however, the low cost of its piston engine competitor tends to eliminate all but the simplest cycles from vehicle gas turbine considerations. In order to improve the part load fuel economy, some complexity is inevitable, but this is limited to the addition of a glass ceramic regenerator in the 150 b.h.p. engine which is described in some detail. The alternative further complications necessary to achieve satisfactory vehicle response at various power/weight ratios are examined. Further improvement in engine performance will come by increasing the maximum cycle temperature. This can be achieved at lower cost by the extension of the use of ceramics. The paper is intended to stimulate the design application of the gas turbine engine.

scholarly journals Textbook Alternative Incentive Programs at U.S. Universities: A Review of the Literature

2020 ◽  
Vol 15 (4) ◽  
pp. 105-123
Author(s):  
Ashley Lierman
Keyword(s):  
Low Cost ◽  
Cost Savings ◽  
The United States ◽  
Design Development ◽  
Impact Measurement ◽  
Grant Programs ◽  
Incentive Programs ◽  
Financial Investments ◽  
Faculty Time ◽  
The Cost

Objective – This article reviews current literature on incentive grant programs for textbook alternatives at universities and their libraries. Of particular interest in this review are common patterns and factors in the design, development, and implementation of these initiatives at the programmatic level, trends in the results of assessment of programs, and unique elements of certain institutions’ programs. Methods – The review was limited in scope to studies in scholarly and professional publications of textbook alternative incentive programs at universities within the United States of America, published within ten years prior to the investigation. A comprehensive literature search was conducted and then subjected to analysis for trends and patterns. Results – Studies of these types of programs have reported substantial total cost savings to affected students compared to the relatively small financial investments that are required to establish them. The majority of incentive programs were led by university libraries, although the most successful efforts appear to have been broadly collaborative in nature. Programs are well-regarded by students and faculty, with benefits to pedagogy and access to materials beyond the cost savings to students. The field of replacing textbooks with alternatives is still evolving, however, and the required investment of faculty time and effort is still a barrier, while inconsistent approaches to impact measurement make it difficult to compare programs or establish best practices. Conclusion – Overall, the literature shows evidence of significant benefits from incentive programs at a relatively low cost. Furthermore, these programs are opportunities to establish cross-campus partnerships and collaborations, and collaboration seems to be effective at helping to reduce barriers and increase impact. Further research is needed on similar programs at community colleges and at higher education institutions internationally.

scholarly journals Low-Cost Differential Pressure Spirometry for Emergency Ventilator Tidal Volume Sensing

2020 ◽  
Author(s):  
Jordan Edmunds ◽  
Mauricio J Bustamante ◽  
Samuel J Raymond ◽  
David B Camarillo ◽  
David K Piech ◽  
...  
Keyword(s):  
United States ◽  
Tidal Volume ◽  
Pressure Sensor ◽  
Low Cost ◽  
Invasive Mechanical Ventilation ◽  
The United States ◽  
Volume Measurement ◽  
Close Monitoring ◽  
Cost Differential ◽  
Volume Measurements

COVID-19 has become a significant burden on the healthcare systems in the United States and around the world, with many patients requiring invasive mechanical ventilation (IMV) to survive. Close monitoring of patients is critical, with total volume per breath (tidal volume) being one of the most important data points. However, ventilators are complex and expensive devices, typically in the range of tens of thousands of US dollars, and are challenging to manufacture, typically requiring months. Solutions which could augment the ventilator supply rapidly and at low cost in the United States and elsewhere would be valuable. In this paper, we present a standalone tidal volume measurement system consisting of a D-Lite spirometer, pressure sensor, microcontroller, and tubing with a cost of parts less than $50 USD. We also provide a model to predict the error in tidal volume measurements based on the pressure sensor used and the flow during ventilation. We validate this system and show that the tidal volume accuracy for flows above 10L/min was within 10%. We envision this system being used to increase the ventilator supply in resource-constrained settings.

‘New Lamps for Old!’ A Method to Rejuvenate Old Robots through the Use of a Simple Set of Microcontroller-Based Control Boards to Replace Outdated Control Systems

2005 ◽  
Vol 33 (4) ◽  
pp. 339-348 ◽  
Author(s):  
P. Brunn ◽  
A. W. Labib
Keyword(s):  
Control System ◽  
Control Systems ◽  
Manufacturing Systems ◽  
Low Cost ◽  
Welding Robot ◽  
Design Development ◽  
Simple Set

The paper describes the design, development, testing and use of a microcontroller- and PC-based control system which was used to repair and enhance an ASEA IRB6 welding robot in the authors' laboratory. The principles described could be applied to any robot of similar age and to provide a low-cost route to revitalise any working robot hardware that is limited by an outdated control system. The proposed approach addresses a problem within many manufacturing systems operating in industry.

Highly responsive screen-printed asymmetric pressure sensor based on laser-induced graphene

2021 ◽  
Author(s):  
Jiang Zhao ◽  
Jiahao Gui ◽  
Jinsong Luo ◽  
Jing Gao ◽  
Caidong Zheng ◽  
...  
Keyword(s):  
Pressure Sensor ◽  
Screen Printing ◽  
Large Scale ◽  
Low Cost ◽  
Pressure Sensors ◽  
High Sensitivity ◽  
Wearable Electronics ◽  
Integrated Sensor ◽  
Patterned Electrodes ◽  
Screen Printed

Abstract Graphene-based pressure sensors have received extensive attention in wearable devices. However, reliable, low-cost, and large-scale preparation of structurally stable graphene electrodes for flexible pressure sensors is still a challenge. Herein, for the first time, laser-induced graphene (LIG) powder are prepared into screen printing ink, and shape-controllable LIG patterned electrodes can be obtained on various substrates using a facile screen printing process, and a novel asymmetric pressure sensor composed of the resulting screen-printed LIG electrodes has been developed. Benefit from the 3D porous structure of LIG, the as-prepared flexible LIG screen-printed asymmetric pressure sensor has super sensing properties with a high sensitivity of 1.86 kPa−1, low detection limit of about 3.4 Pa, short response time, and long cycle durability. Such excellent sensing performances give our flexible asymmetric LIG screen-printed pressure sensor the ability to realize real-time detection of tiny body physiological movements (such as wrist pulse and pronunciation action). Besides, the integrated sensor array has a multi-touch function. This work could stimulate an appropriate approach to designing shape-controllable LIG screen-printed patterned electrodes on various flexible substrates to adapt the specific needs of fulfilling compatibility and modular integration for potential application prospects in wearable electronics.

Inverted Constructivism to Leverage Mobile-Technology-Based Active Learning

2018 ◽  
pp. 240-258
Author(s):  
Doo Hum Lim ◽  
Kristie Tschopp-Harris
Keyword(s):  
Active Learning ◽  
Mobile Technology ◽  
Curriculum Design ◽  
Classroom Environment ◽  
Teaching And Learning ◽  
Low Cost ◽  
Primary Objective ◽  
Mobile Technologies ◽  
Design Development ◽  
The Social

The classroom environment in the 21st century has increasingly utilized many types of technologies as supplemental tools for teaching and learning including instructional design, development, and delivery. The level at which schools are encompassing more technology is often restrained by financial constraints and rapid advances in the static equipment, making the equipment outdated within a short period of time. However, the use of relatively low cost mobile technologies such as tablets and cell phones in the classroom setting have reduced the social and logistical barriers in education and enhanced the creative active learning processes. The primary objective of this chapter is to offer insights into the importance of using mobile technology to educate students in today's connected society and to identify the multi-faceted advantages of mobile technology within an active learning curriculum design to encourage a meaningful learner-centered experience.

scholarly journals Linearly Sensitive and Flexible Pressure Sensor Based on Porous Carbon Nanotube/Polydimethylsiloxane Composite Structure

Polymers ◽  
2020 ◽  
Vol 12 (7) ◽  
pp. 1499 ◽  
Author(s):  
Young Jung ◽  
Kyung Kuk Jung ◽  
Dong Hwan Kim ◽  
Dong Hwa Kwak ◽  
Jong Soo Ko
Keyword(s):  
Carbon Nanotube ◽  
Pressure Sensor ◽  
Porous Carbon ◽  
Composite Structure ◽  
Low Cost ◽  
Human Motion ◽  
Mechanical And Electrical Properties ◽  
Human Motion Detection ◽  
Working Principle ◽  
Flexible Pressure Sensor

We developed a simple, low-cost process to fabricate a flexible pressure sensor with linear sensitivity by using a porous carbon nanotube (CNT)/polydimethylsiloxane (PDMS) composite structure (CPCS). The working principle of this pressure sensor is based on the change in electrical resistance caused by the contact/non-contact of the CNT tip on the surface of the pores under pressure. The mechanical and electrical properties of the CPCSs could be quantitatively controlled by adjusting the concentration of CNTs. The fabricated flexible pressure sensor showed linear sensitivity and excellent performance with regard to repeatability, hysteresis, and reliability. Furthermore, we showed that the sensor could be applied for human motion detection, even when attached to curved surfaces.

Sign in / Sign up

Export Citation Format

Share Document