scholarly journals Optimization and biosynthesis of calcined chicken eggshell doped titanium dioxide photocatalyst based nanoparticles for wastewater treatment

2021 ◽  
Vol 4 (1) ◽  
Author(s):  
Tafere Aga Bullo ◽  
Yigezu Mekonnen Bayisa ◽  
Mohammed Seid Bultum

Abstract This study presents, biosynthesis of calcinated eggshell (CES) doped with Titanium dioxide (TiO2,) photocatalyst for photodegradation of methylene blue from synthetic wastewater. The influence of three independent variables for improving photodegradation efficiency was investigated and optimized using response surface methodology of Box–Behnken Design on the removal of methylene blue using the calcined chicken eggshells (CES) doped with titanium dioxide. The experimental result showed that 95.8% degradation efficiency of methylene blue by prepared photocatalyst at a contact time of 180 min, initial concentration of methylene blue of 10 ppm, and calcined eggshells (CES) doped with titanium dioxide dose of 2.5 g/L. The synthesized photocatalyst was characterized by Fourier-transform infrared spectroscopy, UV-spectrometer, and X-ray diffractometer and UV–vis Spectroscopy for determined their functional group, structure, and bandgap energy respectively. Their results depict the calcined eggshell doped with titanium dioxide photocatalyst is a promising option for the degradation of methylene blue from industrial wastewater under the stated condition. Highlights Analysis of chicken eggshell wastes are being used as photocatalyst source to calcinated eggshell doped TiO2, i.e., ‘Waste to photocatalyst’ for production of viable sustainable products to bio photocatalyst from wastewater to fulfill the need of an expensive metal-doped catalyst. Photocatalytic degradation of Methylene Blue experiment has been done. The highest degradation efficiency of 95.8% methylene blue was obtained at a contact time of 180 min, 10 ppm of initial concentration of methylene blue, and a dopant dose of 2.5 g/L by using prepared photocatalyst.

Author(s):  
Yigezu Mekonnen Bayisa ◽  
Tafere Aga Bullo ◽  
Mohammed Seid Bultum

In recent decades, research concerning and knowledge about the external benefits of renewable raw materials have intensified the efforts for investigating the major sources, causes, and effects of wastewater from solid waste and industries or households. In this study bio-matter and low-cost photocatalyst was prepared for photodegradation on the removal of methylene blue from wastewater treatment, and characterized by Fourier-transform infrared (FTIR) spectroscopy, UV-spectrometer, and X-ray diffractometer (XRD). The effects of initial concentration of methylene blue, amount of dopant, and degradation time were investigated on the percentage degradation of methylene blue using the calcinated eggshell doped titanium dioxide nanoparticle catalysts. At sufficient contact time and low initial concentration, the increment in dopant dose from 0.5 to 2.5 g/l results in an increment of methylene blue degradation efficiency, from 52.5 % to 95.8%. It was shown that a calcinating eggshell doped titanium dioxide photocatalyst method for wastewater treatment is a promising option for the degradation of methylene blue from industrial wastewater under the stated condition.


2021 ◽  
Author(s):  
Siti Nor Atika Baharin ◽  
Nurul Hafawati Hashim ◽  
Izyan Najwa Mohd Norsham ◽  
Syed Shahabuddin ◽  
Kavirajaa Pandian Sambasevam

Abstract The present study highlights the sunlight-assisted photodegradation of methylene blue (MB) using tungsten disulphide/polypyrrole (WS2/PPy) composite as a photocatalyst. WS2/PPy was prepared via oxidative polymerization using ferric chloride (FeCl3) as an oxidant. Fourier Transform Infrared Spectroscopy (FTIR), X-ray diffraction (XRD) and Field Emission Scanning Electron Microscope (FESEM) measurement were used to ensure the physicochemical properties of WS2/PPy. The photocatalytic efficiencies of the photocatalysts were examined by degrading methylene blue (MB) under sunlight irradiation. The results showed that the degradation efficiency of WS2/PPy was higher than the pristine PPy Several optimizations such as effect of the concentration, contact time, photocatalyst dosage and initial concentration were investigated. The results revealed that, under optimum condition of pH 3, 100 mg photocatalyst dosage, 10 ppm MB initial concentration within 180 minutes contact time, were the most effective parameters, that produced 96.15% of sunlight-assisted photodegradation in aqueous solution of MB.


2012 ◽  
Vol 2012 ◽  
pp. 1-5 ◽  
Author(s):  
Gui Bing Hong ◽  
Chih Ming Ma

Titanium dioxide (TiO2) has been extensively studied with regard to its application as the physical sunblock in sunscreen or other cosmetic products, as well as in environmental remediation processes. In this study, the Taguchi method was applied to determine the optimum gaseous DCM (dichloromethane) by Pt-TiO2with different Pt contents. An orthogonal array (L32) experimental design that allows for the simultaneous investigation of the variations of six parameters (light source, catalyst type, initial concentration, retention time, photointensity, and relative humidity) was employed to determine the optimum levels. The value of photointensity was not at a confidence interval. According to the response values and an analysis of variance (ANOVA), an experimental result of 34.7 as the optimum condition is forecast. Although the predetermination of 34.7 is not equal to the experimental value, it is contained within the 90% confidence interval (25.8, 43.6).


2013 ◽  
Vol 330 ◽  
pp. 112-116 ◽  
Author(s):  
Nabilah A. Lutpi ◽  
N. Najihah Jamil ◽  
C.K. Kairulazam C.K. Abdullah ◽  
Yee Shian Wong ◽  
Soon An Ong ◽  
...  

The adsorption of Methylene Blue (MB) and Acid Orange 7 (AO7) dye onto Ananas Comosus Mixed Peels and Leaves (ACMPL) were carried out by conducting four different parameters such as initial concentration, pH, dosage of adsorbent, and contact time. Effect of initial concentration for both dyes showed that higher initial concentration would take longer contact time to attain equilibrium due to higher amount of adsorbate molecules. The effect of pH showed highest percentage removal for MB is at pH 9 which is 95.81%. Meanwhile for AO7 the highest percentage removal is 31.06% at pH 3. The percentage removal of MB had reached the equilibrium at dosage 0.5g while AO7 keep increasing with the increment of adsorbent dosage. The percentage removal of MB and AO7 had increased until hour 2.5 which was from 72.5% to 86.93% and 19.441% to 36.89% respectively and reached equilibrium at 3 hour contact time.


2013 ◽  
Vol 15 (2) ◽  
pp. 40-47 ◽  
Author(s):  
Mohammad Taghi Ghaneian ◽  
Mohammad Hasan Ehrampoush ◽  
Asghar Mosleh Arany ◽  
Behzad Jamshidi ◽  
Mahboobeh Dehvari

In this study the removal of Cr (VI) from synthetic wastewater was investigated using Acroptilon repens (Russian Knapweed) flower powder under various conditions (pH, contact time and initial concentration of Cr). The capacity of chromium adsorption at equilibrium conditions by this biosorbent was increased by adsorbate concentration. The results also showed that the removal efficiency of Cr (VI) was increased by increasing the contact time. By increasing the initial concentration of Cr (VI) solution, chromium removal was reduced. The suitability of adsorbents and their constants was tested or evaluated with the Langmuir, Freundlich and Temkin isotherms models. The results indicated that the Freundlich and Langmuir models (R2 > 0.99) gave a better concordance to the adsorption data in comparison with the Temkin equation (R2 = 0.97). The adsorption of Cr (VI) followed the pseudo-second-order kinetics (R2 = 0.991). The study showed that Acroptilon repens flower powder can be used as an effective lignocellulosic biomaterial and biosorbent for the removal of Cr (VI) from wastewater.


2016 ◽  
Vol 11 (4) ◽  
pp. 155892501601100
Author(s):  
Ali Sajjadi ◽  
Seyed Abdolkarim Hosseini Ravandi ◽  
Hossein Izadan ◽  
Nastaran Kadivar

In this paper, titanium dioxide nanoparticles were synthesized on polyacrylonitrile nanofiber membranes via a sol-gel process. Filter structure consisted of a non-woven polyurethane-carbon substrate, polyacrylonitrile nanofiber and titanium dioxide nanoparticles. The concentration of methylene blue dye solution was measured via UV radiation. The filtration efficiency was calculated via Langmuir-Hinshelwood pseudo-first order equations. The results showed that the filtration efficiency of samples using titanium dioxide under UV rays was higher than those without titanium dioxide and UV rays in both immersing and cross-flow processes. Degradation efficiency of the cross-flow system was three times higher than that of immersing method. In the cross-flow process, the effect of three variables-pressure on the membrane, initial concentration of dye solution and pH of the dye solution was studied under UV rays. The highest efficiency obtained was 90.3% by using 1.5 bar pressure, 40 μM initial concentration and pH of 4.1.


2015 ◽  
Vol 754-755 ◽  
pp. 719-723 ◽  
Author(s):  
Ahmad Zulfadli Mohamad Hashim ◽  
Suriati Sufian ◽  
Maizatul Shima Shaharun

A study of water as the agent of functionalization is still new since most of researchers used acid as the agent of functionalization. The objective of this study is to investigate the used of water as a medium of functionalization of commercialized activated carbon in order to be used in removal of methylene blue dyes from synthetic wastewater via adsorption. The parameters for functionalization of the commercialized activated carbon included temperature at 35°C, contact time of 5 hours and various frequency at 100, 150 and 200 rpm. The experiment was conducted in a batch process where the commercialized activated carbon were functionalized under the mentioned parameters. The functionalized activated carbon were characterized using Fourier Transform Infra-Red (FTIR) Spectroscopy. The FTIR analysis indicated the increase of the amount of functional group attached to the activated carbon. The dye adsorption study was conducted by using methylene blue solution with initial concentration of 500 ppm as adsorbate and the functionalized activated carbon as adsorbent. A standard calibration curve for methylene blue solution was generated using of Ultraviolet-Visible (Uv-Vis) Spectrophotometer. The result from the adsorption study was the parameter of temperature at 35°C, contact time of 5 hours and varying water bath shaker frequency at 100 rpm yield the best adsorption rate.


2019 ◽  
Vol 20 (1) ◽  
pp. 130 ◽  
Author(s):  
Ani Iryani ◽  
Hadi Nur ◽  
Mardi Santoso ◽  
Djoko Hartanto

Rhodamine B (RB) and Methylene Blue (MB) dyes adsorption using adsorbent ZSM-5 synthesized from Bangka kaolin were investigated in this study. The effects of the initial concentration, contact time and temperature on the adsorption process were also analyzed. The effect of the initial concentration and contact time played an important role in the adsorption process; however, the effect differs significantly in both dyes. The temperature plays little role in the dye adsorption process. The results showed the adsorption process occurred in ZSM-5 adhere to Langmuir isothermal adsorption model showing that the adsorption process occurred to be monolayer. Based on the kinetics studies, the pseudo-first-order kinetic model represents the adsorption kinetics that occurs for both dyes onto the synthesized ZSM-5. Thermodynamic parameters namely Gibbs free energy (ΔG°), standard entropy changes (ΔS°) and standard enthalpy (ΔH°) reveal that the adsorption process onto ZSM-5 for both dyes was spontaneous and exothermic.


Author(s):  
Alica Pastierová ◽  
Maroš Sirotiak

Abstract This paper presents a study into dynamic behaviour of the methylene blue adsorption (MB) on activated carbon. Effect of four parameters were studied: effect of the adsorbent dosage, effect of contact time, effect of pH, and effect of the initial concentration of methylene blue. The adsorption kinetic data were modelled using the pseudo-first and pseudo-second orders. Results show that, based on the experimental data, the pseudo-second order could be considered satisfactory. Thermodynamic parameters proved that adsorption of dye was spontaneous owing to increase in temperature and endothermic nature. Taguchi method was applied to determine the optimum conditions for removal of methylene blue by activated carbon. The optimum conditions were found to be pH = 7, contact time 60 min, initial concentration of MB 4 mg/L.


2012 ◽  
Author(s):  
Hasril Azuan Abdullah Hashim ◽  
Abdul Rahman Mohamed ◽  
Keat Teong Lee

Perawatan air sisa semakin mendapat perhatian kebelakangan ini, sehingga menjurus kepada penemuan fotopemangkinan, satu kaedah alternatif perawatan air sisa yang berpotensi. Sehingga kini, banyak penyelidikan yang berkaitan dengan pemusnahan bahan pencemar organik tunggal telah dijalankan. Walau bagaimanapun, aplikasinya terhadap pendetoksifikasi sampel campuran bahan pencemar dengan tahap Jumlah Karbon Organik yang tinggi tidak dikaji secara menyeluruh. Walaupun terdapat banyak kaedah perawatan pada masa kini, kebanyakannya tidak memusnahkan bahan pencemar secara lengkap, tetapi hanya menyebabkan perubahan fasa atau pemusnahan bahan pencemar secara separa sahaja. Berbeza daripada kaedah perawatan yang lain, proses fotopemangkinan ialah teknologi bersih yang hanya menggunakan tenaga suria, air dan mangkin yang boleh digunakan semula bagi memusnahkan toksin atau bahan pencemar dalam air. Dalam proses fotopemangkinan, fotomangkin semikonduktor boleh diaktifkan hanya dengan menggunakan sinaran ultra lembayung (UV) daripada radiasi cahaya matahari. Fotomangkin yang telah diaktifkan akan menghasilkan radikal hidroksil yang berkebolehan untuk mendegradasikan bahan cemar. Dalam kajian ini, fotomangkin yang digunakan ialah titanium dioksida (TiO2) dan tartrazin dipilih sebagai bahan cemar. Tartrazin ialah sejenis pewarna yang banyak digunakan dalam industri makanan dan mudah larut dalam air. Pewarna sintetik ini boleh mengakibatkan kanser pada kepekatan yang tinggi. Uji kaji fotopemangkinan dijalankan dengan mengubah jumlah mangkin yang digunakan (0–1.5 g/L), kepekatan awal larutan pewarna (5–35 ppm), dan kadar aliran larutan pewarna (1.0–1.5 L/min). Larutan pewarna didedahkan kepada sinaran matahari selama dua jam. Keputusan uji kaji menunjukkan bahawa peratus degradasi pewarna yang tinggi boleh dicapai dengan menggunakan kombinasi sinaran cahaya dan TiO2. Jumlah mangkin optimum yang digunakan untuk proses degradasi pewarna ini ialah 1.0 g/L. Kepekatan asal pewarna tartrazin dan kadar aliran larutan tartrazin didapati mempengaruhi peratus degradasi pewarna. Kepekatan asal tartrazin yang lebih tinggi mengakibatkan kecekapan proses degradasi menurun, manakala kadar aliran larutan tartrazin yang lebih tinggi mengakibatkan kecekapan proses degradasi meningkat. Kata kunci: Foto-pemangkinan; mangkin TiO; tartrazin; pendetoksifikasi suria As wastewater treatments become more important nowadays, photocatalysis, an alternative wastewater treatment method, shows a promising potential. By now, many studies on the photocatalytic destruction of single organic contaminants have been carried out However, its application to the detoxification of samples of contaminants mixtures with high Total Organic Carbon levels has not been thoroughly investigated. Although presently many treatment methods are being used, most of them do not completely destroy the pollutants but only offer phase transfer or partial degradation of the pollutants. On the other hand, solar photocatalytic process is an exciting clean technology that uses only sunlight, water, and a reusable catalyst to remove toxins or pollutants from water. In a photocatalytic process, a semiconductor photocatalyst is activated with ultraviolet (UV) irradiation from the sun. The activated photocatalyst promotes the formation of hydroxyl radicals, which in turn completely degrade the pollutants. In this study, the photocatalyst used was titanium dioxide (TiO2) and tartrazine was chosen as the pollutant. Tartrazine is one of the popular water soluble dyes used in food coloring industries but it is carcinogenic at high concentration. The photocatalytic experiments were conducted with varying catalyst loading (0-1.5 g/L), initial concentration (5-35 ppm), and flowrate of tartrazine solution (1.0-1.5 L/min). The dye solution was exposed to sunlight for about two hours. The experimental results showed that a considerable increase in the degradation efficiency of the tartrazine-compound could be obtained by a combination of TiO2 and solar light. The optimum catalyst weight loading for the degradation of tartrazine dye was found to be 1.0 g/L. The initial concentration of the tartrazine dye and flowrate of tartrazine solution were found to effect the degradation efficiency of the dye. Higher initial concentration resulted in lower degradation efficiencies, while higher tartrazine solution flowrate resulted in higher degradation efficiency. Key words: Photocatalytic; solar detoxification; tartrazine; TiO2 catalyst


Sign in / Sign up

Export Citation Format

Share Document