Effect of hydrogen on the mechanical properties at high temperature of fast-neutron irradiated Ti alloys

1981 ◽  
Vol 104 ◽  
pp. 925-929 ◽  
Author(s):  
Y. Higashiguchi ◽  
H. Kayano ◽  
M. Miyake
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Fast Neutron ◽  
Ti Alloys

Effect of Zr Addition on High Temperature Mechanical Properties of Near Alpha Ti-Al-Zr-Sn Based Alloy

2014 ◽  
Vol 783-786 ◽  
pp. 580-583 ◽  
Author(s):  
Murugesan Jayaprakash ◽  
De Hai Ping ◽  
Y. Yamabe-Mitarai
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Room Temperature ◽  
High Temperature Strength ◽  
Test Results ◽  
High Temperature Mechanical Properties ◽  
Ti Alloys ◽  
Zr Addition ◽  
And Performance ◽  
Compressive Tests

Titanium (Ti) alloys are widely used in aerospace industries successfully up to 600°C. Increasing the operating temperature and performance of these alloys would be very useful for fuel economy. Numerous numbers of research works has been focused on the improvement of the high temperature performances of Ti alloys. It has been well known that Zirconium (Zr) is one of the important solid-solution strengthener in Ti-alloys. In the present study, the effect of Zr addition on the microstructure and mechanical properties of the near–α Ti-Al-Zr-Sn based alloys has been investigated.The compression test results showed that Zr addition significantly improves both room temperature and high temperature strength. The results obtained were explained based on the microstructural observation, room temperature and high temperature compressive tests.

Mechanical properties of ferrous alloys after fast neutron-irradiation at high temperature

1979 ◽  
Vol 80 (2) ◽  
pp. 379-382
Author(s):  
Yasuhiro Higashiguchi ◽  
Hideo Kayano ◽  
Minoru Narui ◽  
Yoshimitsu Suzuki ◽  
Kenzo Matsuyama ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Fast Neutron ◽  
Neutron Irradiation ◽  
Ferrous Alloys ◽  
Fast Neutron Irradiation

Phase Equilibria in the Nb-rich Nb-Ti-Si-Cr-Hf alloys

2011 ◽  
Vol 1295 ◽  
Author(s):  
Ying Yang ◽  
Bernard P. Bewlay ◽  
Austin Chang
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Phase Equilibria ◽  
Calphad Approach ◽  
Rich Region ◽  
Isothermal Sections ◽  
Beneficial Effects ◽  
High Temperature Materials ◽  
Ti Alloys ◽  
Alloying Effects

ABSTRACTRefractory Metal-Intermetallic Composites (RMICs) based on the Nb-Si system have been considered as candidates for the next-generation high temperature materials (i.e. >1200°C). Ti, Cr and Hf have been shown to have beneficial effects on the oxidation resistance and mechanical properties of Nb-Si alloys. The present study has determined phase equilibria in the Nb-rich region of the Nb-Si-Ti-Cr-Hf system via the Calphad approach. The alloying effects of Cr and Hf on the microstructure of Nb-Si-Ti alloys are understood based on isothermal sections, liquidus projections, and solidification curves that were calculated from the thermodynamic models of the Nb-Ti-Si-Cr-Hf system developed in the present study. This work provides important guidelines on the development of new Nb-Si-Ti-Cr-Hf alloys.

Mechanical properties of near alpha titanium alloys for high-temperature applications - a review

2020 ◽  
Vol 92 (4) ◽  
pp. 521-540 ◽  
Author(s):  
Vitus Mwinteribo Tabie ◽  
Chong Li ◽  
Wang Saifu ◽  
Jianwei Li ◽  
Xiaojing Xu
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
High Temperature ◽  
Titanium Alloys ◽  
Content Type ◽  
The Past ◽  
Ti Alloys ◽  
Multiaxial Compression ◽  
Aero Engines ◽  
Temperature Applications

Purpose This paper aims to present a broad review of near-a titanium alloys for high-temperature applications. Design/methodology/approach Following a brief introduction of titanium (Ti) alloys, this paper considers the near-α group of Ti alloys, which are the most popular high-temperature Ti alloys developed for a high-temperature application, particularly in compressor disc and blades in aero-engines. The paper is relied on literature within the past decade to discuss phase stability and microstructural effect of alloying elements, plastic deformation and reinforcements used in the development of these alloys. Findings The near-a Ti alloys show high potential for high-temperature applications, and many researchers have explored the incorporation of TiC, TiB SiC, Y2O3, La2O3 and Al2O3 reinforcements for improved mechanical properties. Rolling, extrusion, forging and some severe plastic deformation (SPD) techniques, as well as heat treatment methods, have also been explored extensively. There is, however, a paucity of information on SiC, Y2O3 and carbon nanotube reinforcements and their combinations for improved mechanical properties. Information on some SPD techniques such as cyclic extrusion compression, multiaxial compression/forging and repeated corrugation and straightening for this class of alloys is also limited. Originality/value This paper provides a topical, technical insight into developments in near-a Ti alloys using literature from within the past decade. It also outlines the future developments of this class of Ti alloys.

Lattice Imaging of Grain Boundaries in Ceramics

1977 ◽  
Vol 35 ◽  
pp. 114-115
Author(s):  
D. R. Clarke ◽  
G. Thomas
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Silicon Nitride ◽  
Grain Boundaries ◽  
High Temperature Strength ◽  
Current Interest ◽  
Lattice Imaging ◽  
Special Significance ◽  
Structural Applications ◽  
Refractory Ceramics

Grain boundaries have long held a special significance to ceramicists. In part, this has been because it has been impossible until now to actually observe the boundaries themselves. Just as important, however, is the fact that the grain boundaries and their environs have a determing influence on both the mechanisms by which powder compaction occurs during fabrication, and on the overall mechanical properties of the material. One area where the grain boundary plays a particularly important role is in the high temperature strength of hot-pressed ceramics. This is a subject of current interest as extensive efforts are being made to develop ceramics, such as silicon nitride alloys, for high temperature structural applications. In this presentation we describe how the techniques of lattice fringe imaging have made it possible to study the grain boundaries in a number of refractory ceramics, and illustrate some of the findings.

TEM Studies of Grain Boundary Films in Si3N4 Ceramics

1991 ◽  
Vol 49 ◽  
pp. 930-931
Author(s):  
H.-J. Kleebe ◽  
J.S. Vetrano ◽  
J. Bruley ◽  
M. Rühle
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Silicon Nitride ◽  
Hot Isostatic Pressing ◽  
Amorphous Film ◽  
Liquid Phase Sintering ◽  
Second Phase ◽  
High Temperature Mechanical Properties ◽  
Triple Points ◽  
Boundary Films

It is expected that silicon nitride based ceramics will be used as high-temperature structural components. Though much progress has been made in both processing techniques and microstructural control, the mechanical properties required have not yet been achieved. It is thought that the high-temperature mechanical properties of Si3N4 are limited largely by the secondary glassy phases present at triple points. These are due to various oxide additives used to promote liquid-phase sintering. Therefore, many attempts have been performed to crystallize these second phase glassy pockets in order to improve high temperature properties. In addition to the glassy or crystallized second phases at triple points a thin amorphous film exists at two-grain junctions. This thin film is found even in silicon nitride formed by hot isostatic pressing (HIPing) without additives. It has been proposed by Clarke that an amorphous film can exist at two-grain junctions with an equilibrium thickness.

AEM of reaction-bonded SiC

1992 ◽  
Vol 50 (1) ◽  
pp. 344-345
Author(s):  
K Das Chowdhury ◽  
R. W. Carpenter ◽  
W. Braue
Keyword(s):  
Mechanical Properties ◽  
Phase Transformation ◽  
High Temperature ◽  
Epitaxial Growth ◽  
Liquid Silicon ◽  
Structural Ceramic ◽  
Few Data

Research on reaction-bonded SiC (RBSiC) is aimed at developing a reliable structural ceramic with improved mechanical properties. The starting materials for RBSiC were Si,C and α-SiC powder. The formation of the complex microstructure of RBSiC involves (i) solution of carbon in liquid silicon, (ii) nucleation and epitaxial growth of secondary β-SiC on the original α-SiC grains followed by (iii) β>α-SiC phase transformation of newly formed SiC. Due to their coherent nature, epitaxial SiC/SiC interfaces are considered to be segregation-free and “strong” with respect to their effect on the mechanical properties of RBSiC. But the “weak” Si/SiC interface limits its use in high temperature situations. However, few data exist on the structure and chemistry of these interfaces. Microanalytical results obtained by parallel EELS and HREM imaging are reported here.

ALUMINUM 220

Alloy Digest ◽  
1962 ◽  
Vol 11 (3) ◽  
Keyword(s):  
Mechanical Properties ◽  
Corrosion Resistance ◽  
Shear Strength ◽  
High Temperature ◽  
Heat Treating ◽  
Casting Alloy ◽  
Aluminum Casting ◽  
Aluminum Casting Alloy ◽  
Temperature Performance ◽  
Aluminum Company

Abstract ALUMINUM 220 is a 10% magnesium-aluminum casting alloy having the highest combination of mechanical properties, corrosion resistance and machinability. This datasheet provides information on composition, physical properties, hardness, elasticity, tensile properties, and compressive and shear strength as well as fatigue. It also includes information on high temperature performance and corrosion resistance as well as casting, heat treating, machining, and joining. Filing Code: Al-112. Producer or source: Aluminum Company of America.

Sign in / Sign up

Export Citation Format

Share Document