Effect of Zr Addition on High Temperature Mechanical Properties of Near Alpha Ti-Al-Zr-Sn Based Alloy

2014 ◽  
Vol 783-786 ◽  
pp. 580-583 ◽  
Author(s):  
Murugesan Jayaprakash ◽  
De Hai Ping ◽  
Y. Yamabe-Mitarai
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Room Temperature ◽  
High Temperature Strength ◽  
Test Results ◽  
High Temperature Mechanical Properties ◽  
Ti Alloys ◽  
Zr Addition ◽  
And Performance ◽  
Compressive Tests

Titanium (Ti) alloys are widely used in aerospace industries successfully up to 600°C. Increasing the operating temperature and performance of these alloys would be very useful for fuel economy. Numerous numbers of research works has been focused on the improvement of the high temperature performances of Ti alloys. It has been well known that Zirconium (Zr) is one of the important solid-solution strengthener in Ti-alloys. In the present study, the effect of Zr addition on the microstructure and mechanical properties of the near–α Ti-Al-Zr-Sn based alloys has been investigated.The compression test results showed that Zr addition significantly improves both room temperature and high temperature strength. The results obtained were explained based on the microstructural observation, room temperature and high temperature compressive tests.

Performance Analysis of Fire-Resistant H-Beam Steel

2010 ◽  
Vol 163-167 ◽  
pp. 2949-2952
Author(s):  
Jian Qing Qian ◽  
Ji Ping Chen ◽  
Bao Qiao Wu ◽  
Jie Ca Wu
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Chemical Composition ◽  
Room Temperature ◽  
High Temperature Strength ◽  
High Temperature Mechanical Properties ◽  
H Beam ◽  
Hot Rolled ◽  
Very High ◽  
Room Temperature Strength

The fire-resistant hot-rolled H-beam steel is the newly developed structure material. The development situation of the fire-resistant H-beam steel is briefly introduced. The chemical composition, microstructure, room temperature and high temperature mechanical properties and weldability of several batches of the developed domestic fire-resistant hot-rolled H-beam steels are comprehensively analyzed. The results show that the newly developed hot-rolled fire-resistant H-beam steel has very high room temperature strength, certain high temperature strength, good welding performance, but the toughness needs to be further improved. The performance of web and flange of H-beam steel has large gap.

scholarly journals The Influence of La and Ce on Microstructure and Mechanical Properties of an Al-Si-Cu-Mg-Fe Alloy at High Temperature

Metals ◽  
2021 ◽  
Vol 11 (3) ◽  
pp. 384
Author(s):  
Andong Du ◽  
Anders E. W. Jarfors ◽  
Jinchuan Zheng ◽  
Kaikun Wang ◽  
Gegang Yu
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
High Temperature ◽  
Intermetallic Phases ◽  
High Temperature Strength ◽  
Thermal Expansion Mismatch ◽  
Strengthening Mechanisms ◽  
High Temperature Mechanical Properties ◽  
Minor Contribution ◽  
A Minor

The effect of lanthanum (La)+cerium (Ce) addition on the high-temperature strength of an aluminum (Al)–silicon (Si)–copper (Cu)–magnesium (Mg)–iron (Fe)–manganese (Mn) alloy was investigated. A great number of plate-like intermetallics, Al11(Ce, La)3- and blocky α-Al15(Fe, Mn)3Si2-precipitates, were observed. The results showed that the high-temperature mechanical properties depended strongly on the amount and morphology of the intermetallic phases formed. The precipitated tiny Al11(Ce, La)3 and α-Al15(Fe, Mn)3Si2 both contributed to the high-temperature mechanical properties, especially at 300 °C and 400 °C. The formation of coarse plate-like Al11(Ce, La)3, at the highest (Ce-La) additions, reduced the mechanical properties at (≤300) ℃ and improved the properties at 400 ℃. Analysis of the strengthening mechanisms revealed that the load-bearing mechanism was the main contributing mechanism with no contribution from thermal-expansion mismatch effects. Strain hardening had a minor contribution to the tensile strength at high-temperature.

Manufacturing and High Temperature Mechanical Properties of Inconel 713C by Using Metal Injection Molding

2012 ◽  
Vol 602-604 ◽  
pp. 627-630 ◽  
Author(s):  
Kyu Sik Kim ◽  
Kee Ahn Lee ◽  
Jong Ha Kim ◽  
Si Woo Park ◽  
Kyu Sang Cho
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Injection Molding ◽  
Room Temperature ◽  
Tensile Tests ◽  
Metal Injection Molding ◽  
Injection Molding Process ◽  
Molding Process ◽  
High Temperature Mechanical Properties ◽  
Inconel 713C

Inconel 713C alloy was tried to manufacture by using MIM(Metal Injection Molding) process. The high-temperature mechanical properties of MIMed Inconel 713C were also investigated. Processing defects such as pores and binders could be observed near the surface. Tensile tests were conducted from room temperature to 900°C. The result of tensile tests showed that this alloy had similar or somewhat higher strengths (YS: 734 MPa, UTS: 968 MPa, elongation: 7.16 % at room temperature) from RT to 700°C than those of conventional Inconel 713C alloys. Above 800°C, however, ultimate tensile strength decreased rapidly with increasing temperature (lower than casted Inconel 713C). Based on the observation of fractography, initial crack was found to have started near the surface defects and propagated rapidly. The superior mechanical properties of MIMed Inconel 713C could be obtained by optimizing the MIM process parameters.

Influence of Al-Cu-Mn-Fe-Ti Alloy Composition and Production Parameters of Extruded Semi-Finished Products on their Structure and Mechanical Properties

2017 ◽  
Vol 265 ◽  
pp. 456-462 ◽  
Author(s):  
P.L. Reznik ◽  
Mikhail Lobanov
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Thermal Treatment ◽  
Low Temperature ◽  
Room Temperature ◽  
High Temperature Strength ◽  
Ti Alloy ◽  
Low Temperature Annealing ◽  
Annealing Conditions ◽  
Concentration Changes

Studies have been conducted as to the effect of Cu, Mn, Fe concentration changes in Al-Cu-Mn-Fe-Ti alloy, the conditions of thermal and deformational treatment of ingots and extruded rods 40 mm in diameter on the microstructure, phase composition and mechanical properties. It has been determined that changing Al-6.3Cu-0.3Mn-0.17Fe-0.15Ti alloy to Al-6.5Cu-0.7Mn-0.11Fe-0.15Ti causes an increase in the strength characteristics of extruded rods at the room temperature both after molding and in tempered and aged conditions, irrespective of the conditions of thermal treatment of the initial ingot (low-temperature annealing 420 °С for 2 h, or high-temperature annealing at 530 °С for 12 h). Increasing the extruding temperature from 330 to 480 °С, along with increasing Cu, Mn and decreasing Fe in the alloy Al-Cu-Mn-Ti, is accompanied by the increased level of ultimate strength in a quenched condition by 25% to 410 MPa, irrespective of the annealing conditions of the original ingot. An opportunity to apply the Al-6.3Cu-0.3Mn-0.17Fe-0.15Ti alloy with low-temperature annealing at 420 °С for 2 h and the molding temperature of 330 °С has been found to produce rods where, in the condition of full thermal treatment (tempering at 535 °С + aging at 200 °С for 8 hours), a structure is formed that ensures satisfactory characteristics of high temperature strength by resisting to fracture for more than 100 hours at 300 °С and 70 MPa.

Deformation of an extruded nickel beryllide between room temperature and 820 °C

1991 ◽  
Vol 6 (12) ◽  
pp. 2653-2659 ◽  
Author(s):  
G.M. Pharr ◽  
S.V. Courington ◽  
J. Wadsworth ◽  
T.G. Nieh
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Elevated Temperature ◽  
Flow Stress ◽  
Strain Hardening ◽  
Room Temperature ◽  
High Temperature Strength ◽  
Compression Tests ◽  
Tension And Compression ◽  
Better Than

The mechanical properties of nickel beryllide, NiBe, have been investigated in the temperature range 20–820 °C. The room temperature properties were studied using tension, bending, and compression tests, while the elevated temperature properties were characterized in compression only. NiBe exhibits some ductility at room temperature; the strains to failure in tension and compression are 1.3% and 13%, respectively. Fracture is controlled primarily by the cohesive strength of grain boundaries. At high temperatures, NiBe is readily deformable—strains in excess of 30% can be achieved at temperatures as low as 400 °C. Strain hardening rates are high, and the flow stress decreases monotonically with temperature. The high temperature strength of NiBe is as good or better than that of NiAl, but not quite as good as CoAl.

The Influence on High-Temperature Mechanical Properties of Hybrid-Fiber-Reinforced High-Performance Concrete and Microscopic Analysis

2012 ◽  
Vol 226-228 ◽  
pp. 1709-1713
Author(s):  
Lan Yan ◽  
Y.M. Xing ◽  
Ji Jun Li
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Transition Zone ◽  
High Performance ◽  
Room Temperature ◽  
Steel Fiber ◽  
High Performance Concrete ◽  
Interfacial Transition Zone ◽  
Hybrid Fiber ◽  
High Temperature Mechanical Properties

This paper investigated the high temperature mechanical properties of the hybrid fiber reinforced high performance concrete (HFHPC) and normal concrete (NC) .After being subjected to different elevated heating temperatures, two kinds of concretes have been tested for the compressive strength, splitting tensile strength and flexural strength of test specimen at room temperature and 200 °C,400 °C,600 °C,800 °C.Microstructure changes of concrete were also observed by using Scanning Electron Microscopy (SEM) after high temperature. The results show that the hybrid fiber can significantly increase mechanical properties of the concrete at room temperature and high temperature. SEM and XRD analysis shows that there is a permeable diffusion layer in the steel fiber surface because of solid state reaction in the Interfacial Transition Zone of steel fiber and concrete. This permeable diffusion layer is white, bright, serrated and mainly consist of FeSi2 and the complex hydrated calcium silicate. The compounds of this layer change the Interfacial Transition Zone structure, enhance bonding capacity of the steel fiber and matrix, and increase the high temperature mechanical properties of concrete.

High-Temperature Mechanical Properties of Al2O3/Ti3SiC2 Multilayer Ceramics

2007 ◽  
Vol 280-283 ◽  
pp. 1877-1880 ◽  
Author(s):  
Qing Feng Zan ◽  
Chang An Wang ◽  
Li Min Dong ◽  
Yong Huang
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Room Temperature ◽  
Diffusion Creep ◽  
Creep Function ◽  
High Temperature Mechanical Properties ◽  
Multilayer Composites ◽  
Dislocation Movement ◽  
Monolithic Ceramics ◽  
Multilayer Materials

The high-temperature mechanical properties were very important to structural materials, especially structural ceramics. Hence, the strength, elastic modulus, stress relaxation and creep behavior of the multilayer materials at elevated temperature were studied in this paper. According to the curves of mechanical properties varieties with temperature risen from room-temperature to 1300°C, the multilayer materials could remain relatively high mechanical properties until 1150°C. Otherwise, the creep function of the multilayer composites was also determined, in which the stress exponent was 1.4 and activation energy was 204kJ/mol. By contrasting to the monolithic ceramics of Al2O3 and Ti3SiC2, the main creep mechanisms include: interface diffusion creep (in Al2O3 layers), dislocation movement creep, grain delamination and sliding (in Ti3SiC2 layers).

scholarly journals Influence of Al2O3 content on mechanical properties of silica-based ceramic cores prepared by stereolithography

2021 ◽  
Author(s):  
Wen Zheng ◽  
Jia-Min Wu ◽  
Shuang Chen ◽  
Chang-Shun Wang ◽  
Chun-Lei Liu ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Flexural Strength ◽  
Room Temperature ◽  
Linear Shrinkage ◽  
Fused Silica ◽  
Al2o3 Content ◽  
High Temperature Mechanical Properties ◽  
Silica Ceramic ◽  
Excellent Chemical

AbstractSilica ceramic cores have played an important part in the manufacture of hollow blades due to their excellent chemical stability and moderate high-temperature mechanical properties. In this study, silica-based ceramics were prepared with Al2O3 addition by stereolithography, and the influence of Al2O3 content on mechanical properties of the silica-based ceramics was investigated. The Al2O3 in silica-based ceramics can improve the mechanical properties by playing a role as a seed for the crystallization of fused silica into cristobalite. As a result, with the increase of Al2O3 content, the linear shrinkage of the silica-based ceramics first decreased and then increased, while the room-temperature flexural strength and the high-temperature flexural strength first increased and then decreased. As the Al2O3 content increased to 1.0 vol%, the linear shrinkage was reduced to 1.64% because of the blocked viscous flow caused by Al2O3. Meanwhile, the room-temperature flexural strength and the high-temperature flexural strength were improved to 20.38 and 21.43 MPa with 1.0 vol% Al2O3, respectively, due to the increased α-cristobalite and β-cristobalite content. Therefore, using the optimal content of Al2O3 in silica-based ceramics can provide excellent mechanical properties, which are suitable for the application of ceramic cores in the manufacturing of hollow blades.

Influence of Interfacial Characteristics on the Mechanical Properties of Continuous Fiber Reinforced Nial Composites

1992 ◽  
Vol 273 ◽  
Author(s):  
Randy R. Bowman
Keyword(s):  
Mechanical Properties ◽  
High Temperature ◽  
Thermal Cycling ◽  
Oxidation Resistance ◽  
Cyclic Oxidation ◽  
Room Temperature ◽  
Matrix Cracking ◽  
High Temperature Strength ◽  
Interfacial Bond ◽  
The Matrix

ABSTRACTAs part of a study to assess NiAl-based composites as potential high-temperature structural materials, the mechanical properties of polycrystalline NiAl reinforced with 30 vol.% continuous single crystal Al2O3 fibers were investigated. Composites were fabricated with either a strong or weak bond between the NiAl matrix and Al2O3 fibers. The effect of interfacial bond strength on bending and tensile properties, thermal cycling response, and cyclic oxidation resistance was examined. Weakly-bonded fibers increased room-temperature toughness of the composite over that of the matrix material but provided no strengthening at high temperatures. With effective load transfer, either by the presence of a strong interfacial bond or by remotely applied clamping loads, Al2O3 fibers increased the high-temperature strength of NiAl but reduced the strain to failure of the composite compared to the monolithic material. Thermal cycling of the weakly-bonded material had no adverse effect on the mechanical properties of the composite. Conversely, because of the thermal expansion mismatch between the matrix and fibers, the presence of a strong interfacial bond generated residual stresses in the composite that lead to matrix cracking. Although undesirable under thermal cycling conditions, a strong interfacial bond was a requirement for achieving good cyclic oxidation resistance in the composite. In addition to the interfacial characterization, compression creep and room temperature fatigue tests were conducted on weakly-bonded NiAl/Al2O3 composites to further evaluate the potential of this system. These results demonstrated that the use of A12O3 fibers was successful in improving both creep and fatigue resistance.

Sign in / Sign up

Export Citation Format

Share Document