Comparative study on permanent deformation in asphalt mixtures from indirect tensile strength testing and laboratory wheel tracking

2021 ◽  
Vol 305 ◽  
pp. 124736
Author(s):  
Filipe Almeida Corrêa Nascimento ◽  
Antonio Carlos Rodrigues Guimarães ◽  
Carmen Dias Castro
Keyword(s):  
Tensile Strength ◽  
Comparative Study ◽  
Permanent Deformation ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Strength Testing ◽  
Indirect Tensile ◽  
Wheel Tracking

scholarly journals Rejuvenation Mechanism of Asphalt Mixtures Modified with Crumb Rubber

CivilEng ◽  
2021 ◽  
Vol 2 (2) ◽  
pp. 370-384
Author(s):  
Hossein Noorvand ◽  
Kamil Kaloush ◽  
Jose Medina ◽  
Shane Underwood
Keyword(s):  
Tensile Strength ◽  
Dynamic Loading ◽  
Creep Compliance ◽  
Asphalt Mixture ◽  
Crumb Rubber ◽  
Indirect Tensile Strength ◽  
Laboratory Evaluation ◽  
Strength Testing ◽  
Noise Mitigation ◽  
Indirect Tensile

Asphalt aging is one of the main factors causing asphalt pavements deterioration. Previous studies reported on some aging benefits of asphalt rubber mixtures through laboratory evaluation. A field observation of various pavement sections of crumb rubber modified asphalt friction courses (ARFC) in the Phoenix, Arizona area indicated an interesting pattern of transverse/reflective cracking. These ARFC courses were placed several years ago on existing jointed plain concrete pavements for highway noise mitigation. Over the years, the shoulders had very noticeable and extensive cracking over the joints; however, the driving lanes of the pavement showed less cracking formation in severity and extent. The issue with this phenomenon is that widely adopted theories that stem from continuum mechanics of materials and layered mechanics of pavement systems cannot directly explain this phenomenon. One hypothesis could be that traffic loads continually manipulate the pavement over time, which causes some maltenes (oils and resins) compounds absorbed in the crumb rubber particles to migrate out leading to rejuvenation of the mastic in the asphalt mixture. To investigate the validity of such a hypothesis, an experimental laboratory testing was undertaken to condition samples with and without dynamic loads at high temperatures. This was followed by creep compliance and indirect tensile strength testing. The results showed the higher creep for samples aged with dynamic loading compared to those aged without loading. Higher creep compliance was attributed to higher flexibility of samples due to the rejuvenation of the maltenes. This was also supported by the higher fracture energy results obtained for samples conditioned with dynamic loading from indirect tensile strength testing.

scholarly journals Evaluations of Nano-Sized Hydrated Lime on the Moisture Susceptibility of Hot Mix Asphalt Mixtures

2012 ◽  
Vol 174-177 ◽  
pp. 82-90 ◽  
Author(s):  
Ju Nan Shen ◽  
Zhao Xing Xie ◽  
Fei Peng Xiao ◽  
Wen Zhong Fan
Keyword(s):  
Tensile Strength ◽  
Experimental Design ◽  
Hot Mix Asphalt ◽  
Hydrated Lime ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Moisture Resistance ◽  
Strength Ratio ◽  
Moisture Susceptibility ◽  
Indirect Tensile

The objective of this study was to evaluate the effect of nano-sized hydrated lime on the moisture susceptibility of the hot mix asphalt (HMA) mixtures in terms of three methodologies to introduce into the mixtures. The experimental design for this study included the utilizations of one binder source (PG 64-22), three aggregate sources and three different methods introducing the lime. A total of 12 types of HMA mixtures and 72 specimens were fabricated and tested in this study. The performed properties include indirect tensile strength (ITS), tensile strength ratio (TSR), flow, and toughness. The results indicated that the nano-sized lime exhibits better moisture resistance. Introducing process of the nano-sized lime will produce difference in moisture susceptibility.

scholarly journals Laboratory Evaluation of the Use of Florida Washed Shell in Open-Graded Asphalt Mixtures

Materials ◽  
2021 ◽  
Vol 14 (22) ◽  
pp. 7060
Author(s):  
Mohammad Alharthai ◽  
Qing Lu ◽  
Ahmed Elnihum ◽  
Asad Elmagarhe
Keyword(s):  
Tensile Strength ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Laboratory Evaluation ◽  
Void Content ◽  
Coarse Aggregates ◽  
Significant Difference ◽  
Indirect Tensile ◽  
Marshall Stability

This study investigates the substitution of conventional aggregate with a Florida washed shell in open-graded asphalt mixtures and evaluates the optimal substitution percentage in aggregate gradations of various nominal maximum aggregate sizes (NMASs) (i.e., 4.75, 9.5, and 12.5 mm). Laboratory experiments were performed on open-graded asphalt mixture specimens with the coarse aggregate of sizes between 2.36 and 12.5 mm being replaced by the Florida washed shell at various percentages (0, 15, 30, 45, and 100%). Specimen properties relevant to the performance of open-graded asphalt mixtures in the field were tested, evaluated, and compared. Specifically, a Marshall stability test, Cantabro test, indirect tensile strength test, air void content test, and permeability test were conducted to evaluate the strength, resistance to raveling, cracking resistance, void content, and permeability of open-graded asphalt mixtures. The results show that there is no significant difference in the Marshall stability and indirect tensile strength when the coarse aggregates are replaced with Florida washed shell. This study also found that the optimum percentages of Florida washed shell in open-graded asphalt mixture were 15, 30, and 45% for 12.5, 9.5, and 4.75 mm NMAS gradations, respectively.

Research on Performance of Emulsion Asphalt Cold Reclaimed Mixture with Various RAP Contents

2011 ◽  
Vol 255-260 ◽  
pp. 3432-3436
Author(s):  
Xian Yuan Tang ◽  
Jie Xiao
Keyword(s):  
Tensile Strength ◽  
Low Temperature ◽  
Compression Test ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Beam Test ◽  
Reclaimed Asphalt ◽  
Indirect Tensile ◽  
The Impact

This paper systematically elaborates the impact upon performance of emulsion asphalt cold reclaimed asphalt mixture by different RAP contents, through a series of testing on six cold reclaimed asphalt mixtures with various RAP contents, such as single axle compression test, 15°C indirect tensile strength (ITS) test, 40°C rutting test and -10°C low-temperature bending beam test. Testing results indicate that 15°C ITS decreases from around 0.75 MPa to 0.58 MPa with the RAP content of mixture increasing from 0% to 100%. 40°C dynamic stabilities reduce considerably from around 19,000 time/mm of 0% RAP mixture to 3,600 time/mm of 100% RAP mixture. -10°C failure strains only change from 1500με to 2000με.

Study on Strength Characteristics Improvement of Polyethylene Modified Bituminous Concrete Mixes

2019 ◽  
Vol 803 ◽  
pp. 216-221
Author(s):  
Khwairakpam Lakshman Singh ◽  
Debjani Panda
Keyword(s):  
Tensile Strength ◽  
Permanent Deformation ◽  
Indirect Tensile Strength ◽  
Strength Characteristics ◽  
Strength Ratio ◽  
Modified Binders ◽  
Indirect Tensile ◽  
Modified Binder ◽  
Marshall Stability ◽  
Bituminous Concrete

The present study shows an investigation on improvement of bituminous binder and its mixes using modified binders with different percentage (1% to 7%) of domestic waste polyethylene (PE).The temperature susceptibility and penetration index (PI) of the modified binders were calculated. It is observed that PI value of modified binder is found higher than unmodified binder. The strength characteristics in terms of Marshall Stability and moisture susceptibility expressed in terms of indirect tensile strength ratio (ITSR) of bituminous concrete were determined in the present study. Marshall stability of the bituminous mixture containing 3% PE increased by 34.2% as compare to mixture containing unmodified binder. The addition of 3% PE to neat bitumen, results in an increase of 20% in indirect tensile strength ratio. Using PE modified binder in bituminous concrete mixes increases stability, indirect tensile strength which turn in provide better resistance against permanent deformation.

Research of Mechanical Properties of Asphalt Pavement Materials with WMA and RAP

2012 ◽  
Vol 204-208 ◽  
pp. 3934-3937 ◽  
Author(s):  
Bao Yang Yu ◽  
Yu Wang ◽  
Min Jiang Zhang
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Dynamic Modulus ◽  
Asphalt Pavement ◽  
Asphalt Mixture ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Porous Asphalt ◽  
Compaction Energy ◽  
Indirect Tensile

The objectives of this paper are to characterize the mechanical properties of porous asphalt pavement mixtures containing RAP and a WMA additive using Super pave gyratory compactor and dynamic modulus testing. Four types of asphalt mixtures were evaluated in this study. This study evaluated compaction energy index, permeability, indirect tensile strength, and dynamic modulus for all types of porous asphalt mixtures. All of the asphalt mixtures meet the typical minimum coefficient of permeability in this study. In addition, only a slight decrease in was found when WMA additive was added to the porous asphalt mixture containing RAP. For indirect tensile strength testing, WMA containing RAP was found to have the highest tensile strength among all of the mixtures tested.

Effect of Modified Asphalt Cement of the Performance of Stone Matrix Mixtures

2020 ◽  
Vol 38 (5A) ◽  
pp. 789-800
Author(s):  
Duaa A. Khalaf ◽  
Zaynab I. Qasim ◽  
Karim H. Al Helo
Keyword(s):  
Tensile Strength ◽  
Fracture Resistance ◽  
Laboratory Tests ◽  
Asphalt Binder ◽  
Asphalt Mixtures ◽  
Indirect Tensile Strength ◽  
Asphalt Cement ◽  
Indirect Tensile ◽  
Marshall Stability ◽  
Stone Matrix

This research investigates the behavior of Stone Matrix Asphalt mixtures (SMA) modified with styrene-butadiene-styrene (SBS) polymer at four percentages (1, 2, 3 and 4%) by weight of asphalt cement. The moisture susceptibility and rutting were taken into consideration in this study. To achieve the objective of this research the superpave system is conducted to design the asphalt mixtures. The physical properties of aggregate, bitumen and other mix materials were assessed and evaluated with the laboratory tests. The mixtures were prepared using penetration Graded (40-50) bitumen and a chemical named Polypropylene Fibers was used as a stabilizing additive. Fibers have been used in SMA mixtures for two main reasons: To increase the toughness and fracture resistance of hot mix asphalt (HMA) and to act as a stabilizer to prevent drain down of the asphalt binder. The laboratory tests include indirect tensile strength test, Marshall stability and retained Marshall Stability test (RMS). For rutting test the Roller wheel compactor is used for preparing the asphaltic samples and Wheel tracking device is used to evaluate the rutting of asphaltic slabs. The results showed that the SBS polymer asphalt mixture gave better moisture sensitivity and better fracture resistance according to the study.It is noted that indirect tensile strength ratio (TSR) increases by 93.1 % and the rut depth decreases by 32.5 % when adding 3% SBS polymer to SMA.

scholarly journals Reinforcement of Recycled Foamed Asphalt Using Short Polypropylene Fibers

2013 ◽  
Vol 2013 ◽  
pp. 1-9 ◽  
Author(s):  
Yongjoo Kim ◽  
Tae-Soon Park
Keyword(s):  
Tensile Strength ◽  
Asphalt Binder ◽  
Indirect Tensile Strength ◽  
Polypropylene Fibers ◽  
Foamed Asphalt ◽  
Wheel Tracking Test ◽  
Indirect Tensile ◽  
Reinforcing Effects ◽  
Marshall Stability ◽  
Wheel Tracking

This paper presents the reinforcing effects of the inclusion of short polypropylene fibers on recycled foamed asphalt (RFA) mixture. Short polypropylene fibers of 10 mm length with a 0.15% by weight mixing ratio of the fiber to the asphalt binder were used. The Marshall stability test, the indirect tensile strength test, the resilient modulus test, and wheel tracking test of the RFA mixtures were conducted. The test results were compared to find out the reinforcing effects of the inclusion of the fiber and the other mixtures, which included the conventional recycled foamed asphalt (RFA) mixtures; the cement reinforced recycled foamed asphalt (CRFA) mixtures; the semihot recycled foamed asphalt (SRFA) mixtures; and recycled hot-mix asphalt (RHMA) mixtures. It is found that the FRFA mixture shows higher Marshall stability than the RFA and SRFA mixtures, higher indirect tensile strength than the RFA mixture, and higher rut resistance than the RFA, SRFA, and RHMA mixtures as seen from the wheel tracking test.

Sign in / Sign up

Export Citation Format

Share Document