Lighting energy use in Anding District, Gansu Province, China

2016 ◽  
Vol 32 ◽  
pp. 40-49 ◽  
Author(s):  
Abigail Clarke-Sather ◽  
Yan Li ◽  
Jiansheng Qu
Solar Energy ◽  
2004 ◽  
Author(s):  
Kelly Kissock

This paper describes data and algorithms to estimate typical average interior illuminance from daylighting using a hybrid of Hay, Davies, Klucher, Reindl (HDKR) method for calculating total solar radiation on a tilted surface and the Illuminating Engineering Society (IES) Lumen Method for estimating interior illuminance from daylighting. This hybrid algorithm, in conjunction with typical meteorological data, directly accounts for shading and typical local cloud cover effects on an hour-by-hour basis, which is difficult to do using the IES sky-cover or sky-ratio methods. Several experiments show reasonable agreement between measured and calculated results. Case study examples demonstrate of use of the method, when incorporated into software, to quickly analyze daylighting potential in industrial facilities, and the use of this information to develop specific recommendations for cost-effectively reducing lighting energy use in industrial facilities by improving the utilization of natural lighting.


Solar Energy ◽  
2005 ◽  
Author(s):  
Abdelkarim Nemri ◽  
Moncef Krarti

This paper provides a simplified analysis tool to assess the energy saving potential of daylighting for commercial buildings through skylights. Specifically, the impact of daylighting is investigated for various fenestration opening sizes, glazing types, control strategies, and geographic locations. A top floor of a prototypical office building has been considered in the analysis. The results obtained for the office building can be applied to other types of buildings such as retails stores, schools, and warehouses. Based on the simulation analysis results, it was determined that skylight to floor ratio more than 0.3 does not affect significantly the lighting energy savings. An optimum value of skylight to floor area ratio was found to be 0.2 to minimize the annual total building energy use.


Author(s):  
Heangwoo Lee

In recent years, the need for comfortable visual environments in indoor spaces has increased energy use in buildings. There have been diverse studies on using a light shelf to solve this problem. It is an effective system that allows external natural light deep into indoor spaces through reflection. However, prior studies have used light shelves with a fixed reflectivity, and there are few studies on improving the visual environment through light shelf control. Therefore, this study proposes a movable light shelf with a rolling reflector that can change the reflectivity. To achieve these objectives, we conducted a performance evaluation of the system’s ability to save energy and improve the visual environment. This study built a real scale testbed and conducted a performance evaluation by deriving values for lighting energy consumption, uniformity, and luminance contrast depending on the light shelf variables. We conclude that (1) the light shelf system achieved an energy savings of 13.6% and 5.7%, respectively, compared to a fixed type light shelf, whose reflectivity cannot be changed, and a traditional movable light shelf; (2) in terms of improving the visual environment, results suggest that the visual environment could be improved using a light shelf by deriving light shelf variables that disturb indoor uniformity; and (3) the results verified glare generation conditions by deriving luminance contrast caused by the variables of light shelf angle and its reflectivity.


2001 ◽  
Vol 33 (1) ◽  
pp. 43-55 ◽  
Author(s):  
Paul J Littlefair

Photoelectric switching has the potential to save energy by turning off lighting when daylight illuminances are adequate. However one problem with this control type is frequent switching, annoying occupants. This paper examines three types of control algorithm which can reduce the number of switching operations. Under differential switching, the lighting is switched on if the illuminance falls below a critical value Eon, but not switched off again until the illuminance reaches a substantially higher value Eoff. Another option is the use of a time delay. The final control mode is solar reset where the lighting can only be switched off at certain set times of day. Operation of the various controls was simulated using model room illuminance data recorded every minute. The analysis reveals that solar reset gives the fewest switching operations but at the cost of increased energy consumption. A time delay, where the daylight illuminance has to exceed a target value for a set time before switching off can occur, gives the fewest switch offs for a given lighting energy use. However differential switching ensures that switching off occurs at a favourable adaptation level. The paper outlines ways to predict lighting energy use under the different control strategies.


2012 ◽  
Vol 253-255 ◽  
pp. 741-745 ◽  
Author(s):  
Jin Soo Han ◽  
Youn Kwae Jeong ◽  
Il Woo Lee

Lighting energy shares a large portion of building energy. Although lighting control system is deployed in the building, it has limited effects on reducing lighting energy use without the help of occupancy sensors. We use PC’s power save mode as an occupancy sensor in office buildings that are not equipped with occupancy sensors. When each PC goes to power save mode, it means that there is no one in that area, that is, no occupancy. If we make mapping relation between the lights and the PC’s, we can figure out when the light should be turned on and off from the state of PC’s power save mode. This scheme can contribute to reduction of lighting energy use in buildings that has lighting control system but has no occupancy sensors. The estimated results show the positive effect on reduction of the lighting energy use.


Author(s):  
Aymen Mechergui ◽  
Moncef Krarti

The paper provides the results of a simulation-based analysis to estimate the potential savings in electrical lighting energy use associated with daylighting controls using skylights for open space warehouses. First, the effectiveness of daylighting controls is investigated for several skylight opening areas, glazing types, control strategies, and several locations in Tunisia. A simplified calculation method is then developed to estimate the annual savings in electrical lighting energy use due to daylighting controls in warehouses. The simplified method has been developed and validated for several locations throughout the world.


Sign in / Sign up

Export Citation Format

Share Document