Dynamic response and control analysis of cross flow heat exchangers under variable temperature and flow rate conditions

2015 ◽  
Vol 81 ◽  
pp. 542-553 ◽  
Author(s):  
Tianyi Gao ◽  
Bahgat Sammakia ◽  
James Geer
Keyword(s):  
Dynamic Response ◽  
Flow Rate ◽  
Heat Exchangers ◽  
Variable Temperature ◽  
Cross Flow ◽  
Control Analysis ◽  
Flow Heat ◽  
And Control

Transient Response of a Cross Flow Heat Exchanger Subjected to Temperature and Flow Perturbations

2015 ◽  
Author(s):  
Karthik Silaipillayarputhur ◽  
Stephen A. Idem
Keyword(s):  
Heat Exchanger ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Heat Exchangers ◽  
Cross Flow ◽  
Transient Performance ◽  
Numerical Predictions ◽  
Minimum Capacity ◽  
Flow Heat

The transient performance of a multi-pass cross flow heat exchanger subjected to temperature and mass flow rate perturbations, where the heat exchanger flow circuiting is neither parallel flow nor counter flow, is considered in this work. A detailed numerical study was performed for representative single-pass, two-pass, and three-pass heat exchangers. Numerical predictions were obtained for cases where the minimum capacity rate fluid was subjected to a step change in inlet temperature in absence of mass flow rate perturbations. Likewise, numerical predictions were obtained for the heat exchangers operating initially at steady state, where a step mass flow rate change of the minimum capacity rate fluid was imposed in the absence of any fluid temperature perturbations. The transient performance of this particular heat exchanger configuration subjected to these temperature and flow disturbances has not been discussed previously in the available literature. In the present study the energy balance equations for the hot and cold fluids and the heat exchanger wall were solved using an implicit central finite difference method. A parametric study was conducted by varying the dimensionless quantities that govern the transient response of the heat exchanger over a typical range of values. Because of the storage of energy in the heat exchanger wall, and finite propagation times associated with the inlet perturbations, the outlet temperatures of both fluids do not respond instantaneously. The results are compared with previously published transient performance predictions of multi-pass counter flow and parallel flow heat exchangers.

Review and Analysis of Cross Flow Heat Exchanger Transient Modeling for Flow Rate and Temperature Variations

2015 ◽  
Vol 7 (4) ◽  
Author(s):  
Tianyi Gao ◽  
James Geer ◽  
Bahgat Sammakia
Keyword(s):  
Heat Exchanger ◽  
Mass Flow Rate ◽  
Transient Response ◽  
Mass Flow ◽  
Flow Rate ◽  
Heat Exchangers ◽  
Cross Flow ◽  
Inlet Temperature ◽  
Flow Rate Change ◽  
Flow Heat

Heat exchangers are important facilities that are widely used in heating, ventilating, and air conditioning (HVAC) systems. For example, heat exchangers are the primary units used in the design of the heat transfer loops of cooling systems for data centers. The performance of a heat exchanger strongly influences the thermal performance of the entire cooling system. The prediction of transient phenomenon of heat exchangers is of increasing interest in many application areas. In this work, a dynamic thermal model for a cross flow heat exchanger is solved numerically in order to predict the transient response under step changes in the fluid mass flow rate and the fluid inlet temperature. Transient responses of both the primary and secondary fluid outlet temperatures are characterized under different scenarios, including fluid mass flow rate change and a combination of changes in the fluid inlet temperature and the mass flow rate. In the ε-NTU (number of transfer units) method, the minimum capacity, denoted by Cmin, is the smaller of Ch and Cc. Due to a mass flow rate change, Cmin may vary from one fluid to another fluid. The numerical procedure and transient response regarding the case of varying Cmin are investigated in detail in this study. A review and comparison of several journal articles related to the similar topic are performed. Several sets of data available in the literatures which are in error are studied and analyzed in detail.

Heat and Mass Transfer to Air in a Cross Flow Heat Exchanger with Surface Deluge Cooling

2016 ◽  
Vol 24 (01) ◽  
pp. 1650002 ◽  
Author(s):  
Andrea Diani ◽  
Luisa Rossetto ◽  
Roberto Dall’Olio ◽  
Daniele De Zen ◽  
Filippo Masetto
Keyword(s):  
Heat Exchanger ◽  
Heat Flow ◽  
Flow Rate ◽  
Data Center ◽  
Heat Dissipation ◽  
Cross Flow ◽  
Critical Conditions ◽  
Heat Flow Rate ◽  
External Temperature ◽  
Flow Heat

Cross flow heat exchangers, when applied to cool data center rooms, use external air (process air) to cool the air stream coming from the data center room (primary air). However, an air–air heat exchanger is not enough to cope with extreme high heat loads in critical conditions (high external temperature). Therefore, water can be sprayed in the process air to increase the heat dissipation capability (wet mode). Water evaporates, and the heat flow rate is transferred to the process air as sensible and latent heat. This paper proposes an analytical approach to predict the behavior of a cross flow heat exchanger in wet mode. The theoretical results are then compared to experimental tests carried out on a real machine in wet mode conditions. Comparisons are given in terms of calculated versus experimental heat flow rate and evaporated water mass flow rate, showing a good match between theoretical and experimental values.

Minimum Irreversibility Criteria for Heat Exchanger Configurations

1999 ◽  
Vol 121 (4) ◽  
pp. 241-246 ◽  
Author(s):  
F. E. M. Saboya ◽  
C. E. S. M. da Costa
Keyword(s):  
Heat Capacity ◽  
Heat Exchanger ◽  
Heat Exchangers ◽  
Cross Flow ◽  
Second Law Of Thermodynamics ◽  
The Other ◽  
Maximum Heat ◽  
Transfer Rates ◽  
Mass Flow Rates ◽  
Flow Heat

From the second law of thermodynamics, the concepts of irreversibility, entropy generation, and availability are applied to counterflow, parallel-flow, and cross-flow heat exchangers. In the case of the Cross-flow configuration, there are four types of heat exchangers: I) both fluids unmixed, 2) both fluids mixed, 3) fluid of maximum heat capacity rate mixed and the other unmixed, 4) fluid of minimum heat capacity rate mixed and the other unmixed. In the analysis, the heat exchangers are assumed to have a negligible pressure drop irreversibility. The Counterflow heat exchanger is compared with the other five heat exchanger types and the comparison will indicate which one has the minimum irreversibility rate. In this comparison, only the exit temperatures and the heat transfer rates of the heat exchangers are different. The other conditions (inlet temperatures, mass flow rates, number of transfer units) and the working fluids are the same in the heat exchangers.

Sign in / Sign up

Export Citation Format

Share Document