Microstructure, wear resistance and electrochemical properties of spherical/non-spherical WC reinforced Inconel 625 superalloy by laser melting deposition

2022 ◽  
Vol 74 ◽  
pp. 413-422
Author(s):  
Wanlu Li ◽  
Riufeng Di ◽  
Ruwang Yuan ◽  
Heyu Song ◽  
Jianbo Lei
Keyword(s):  
Wear Resistance ◽  
Electrochemical Properties ◽  
Inconel 625 ◽  
Laser Melting ◽  
Laser Melting Deposition ◽  
Inconel 625 Superalloy

scholarly journals Superior Mechanical Behavior and Fretting Wear Resistance of 3D-Printed Inconel 625 Superalloy

2018 ◽  
Vol 8 (12) ◽  
pp. 2439 ◽  
Author(s):  
Yong Gao ◽  
Mingzhuo Zhou
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Wear Resistance ◽  
Additive Manufacturing ◽  
High Hardness ◽  
Fretting Wear ◽  
Inconel 625 ◽  
3D Printed ◽  
Inconel 625 Superalloy ◽  
Electron Beam Selective Melting

Additive manufacturing (AM) nickel-based superalloys have been demonstrated to equate or exceed mechanical properties of cast and wrought counterparts but their tribological potentials have not been fully realized. This study investigates fretting wear behaviors of Inconel 625 against the 42 CrMo4 stainless steel under flat-on-flat contacts. Inconel 625 is prepared by additive manufacturing (AM) using the electron beam selective melting. Results show that it has a high hardness (335 HV), superior tensile strength (952 MPa) and yield strength (793 MPa). Tribological tests indicate that the AM-Inconel 625 can suppress wear of the surface within a depth of only ~2.4 μm at a contact load of 106 N after 2 × 104 cycles. The excellent wear resistance is attributed to the improved strength and the formation of continuous tribo-layers containing a mixture of Fe2O3, Fe3O4, Cr2O3 and Mn2O3.

scholarly journals Microstructures and Wear Resistance of Laser Melting Deposited Composites on Ati-Alloy

2013 ◽  
Vol 22 (2) ◽  
pp. 096369351302200
Author(s):  
Li Peng
Keyword(s):  
Wear Resistance ◽  
Sliding Wear ◽  
Dry Sliding Wear ◽  
Micro Hardness ◽  
Laser Melting ◽  
Laser Technology ◽  
Nanoscale Particles ◽  
Laser Melting Deposition ◽  
First Time ◽  
Scanning Electron

This work is based on the dry sliding wear of Stellite 4-FeSi-B4C composites deposited on a TA10 titanium alloy using a Laser melting deposition (LMD) technique, the parameters of which are such as to provide almost crack-free composites with very low porosity. To our knowledge, it is the first time that Stellite4-FeSi-B4C mixed powders are deposited as the hard composites by the LMD technique. Scanning electron microscope results indicate the nanoscale particles and nanorods are produced in such composites. Furthermore, due to the characteristics of the laser technology, the ultrafine nanoscale polycrystalline phases can be easily produced. Compared with a TA10 alloy substrate, the improvements of the micro-hardness and wear resistance are obtained for such composites.

Enhanced wear resistance of laser cladded graphene nanoplatelets reinforced Inconel 625 superalloy composite coating

2018 ◽  
Vol 335 ◽  
pp. 334-344 ◽  
Author(s):  
Pingshun Deng ◽  
Chengwu Yao ◽  
Kai Feng ◽  
Xiangxiang Huang ◽  
Zhuguo Li ◽  
...  
Keyword(s):  
Wear Resistance ◽  
Composite Coating ◽  
Graphene Nanoplatelets ◽  
Inconel 625 ◽  
Inconel 625 Superalloy
Sign in / Sign up

Export Citation Format

Share Document