Microstructure and mechanical behavior of Mg-5Zn matrix influenced by particle deformation zone

2021 ◽  
Vol 60 ◽  
pp. 8-20 ◽  
Author(s):  
Quan-xin Shi ◽  
Cui-ju Wang ◽  
Kun-kun Deng ◽  
Kai-bo Nie ◽  
Yucheng Wu ◽  
...  
Keyword(s):  
Mechanical Behavior ◽  
Deformation Zone ◽  
Particle Deformation

Measurement of Strain and Lattice Rotation in the Particle Deformation Zone

2013 ◽  
Vol 753 ◽  
pp. 21-24
Author(s):  
Lawrence C.L. Ko ◽  
Joao Quinta da Fonseca
Keyword(s):  
Deformation Zone ◽  
Electron Backscatter Diffraction ◽  
Local Deformation ◽  
Image Correlation ◽  
Lattice Rotation ◽  
Particle Deformation ◽  
Local Lattice ◽  
Measured Deformation ◽  
Backscatter Diffraction ◽  
First Time

It is known that there is lattice rotation around the particles after deformation, in a so-called Particle Deformation Zone (PDZ), which is thought to be important in randomizing the texture after recrystallization though Particle Stimulated Nucleation (PSN). However, the role of the local distribution of stored energy and its link to local lattice rotation is not well understood, making it impossible to successfully predict PSN efficiency. Here, we present a new method for studying the deformation around particles with the use of Digital Image Correlation (DIC) of High-Resolution Scanning Electron Microscopy (HRSEM) image and Electron BackScatter Diffraction (EBSD) map. Combining these two techniques makes it possible, for the first time, to relate the local deformation fields to remnant changes in local lattice orientation. Initial measurements are made on a model Al-Si alloy deformed in plane-strain condition by channel die compression up to 30%. Our analysis shows that the material deforms heterogeneously with high levels of deformation localized along slip bands. EBSD analysis shows that the lattice distortion in these bands is minimal. The HRDIC analysis clearly shows particles interrupt the slip banding. Local lattice rotation measured by EBSD is considerably less than expected from the measured deformation.

Application of TEM to Deformation, Wear, and Fracture of Ceramics

1974 ◽  
Vol 32 ◽  
pp. 472-473
Author(s):  
B. J. Hockey
Keyword(s):  
Wear Resistance ◽  
High Temperature ◽  
Mechanical Behavior ◽  
Brittle Materials ◽  
High Temperature Strength ◽  
Wide Range ◽  
Corrosive Environments ◽  
Further Development

Ceramics, such as Al2O3 and SiC have numerous current and potential uses in applications where high temperature strength, hardness, and wear resistance are required often in corrosive environments. These materials are, however, highly anisotropic and brittle, so that their mechanical behavior is often unpredictable. The further development of these materials will require a better understanding of the basic mechanisms controlling deformation, wear, and fracture.The purpose of this talk is to describe applications of TEM to the study of the deformation, wear, and fracture of Al2O3. Similar studies are currently being conducted on SiC and the techniques involved should be applicable to a wide range of hard, brittle materials.

The influence of the addition of ground olive stone on the thermo-mechanical behavior of compressed earth blocks

2020 ◽  
Vol 108 (2) ◽  
pp. 203
Author(s):  
Samia Djadouf ◽  
Nasser Chelouah ◽  
Abdelkader Tahakourt
Keyword(s):  
Thermal Conductivity ◽  
Compressive Strength ◽  
Mechanical Behavior ◽  
Agricultural Waste ◽  
Hydraulic Press ◽  
Dry Density ◽  
Olive Stone ◽  
Compressed Earth Blocks ◽  
Clay Matrix ◽  
Earth Blocks

Sustainable development and environmental challenges incite to valorize local materials such as agricultural waste. In this context, a new ecological compressed earth blocks (CEBS) with addition of ground olive stone (GOS) was proposed. The GOS is added as partial clay replacement in different proportions. The main objective of this paper is to study the effect of GOS levels on the thermal properties and mechanical behavior of CEB. We proceeded to determining the optimal water content and equivalent wet density by compaction using a hydraulic press, at a pressure of 10 MPa. The maximum compressive strength is reached at 15% of the GOS. This percentage increases the mechanical properties by 19.66%, and decreases the thermal conductivity by 37.63%. These results are due to the optimal water responsible for the consolidation and compactness of the clay matrix. The substitution up to 30% of GOS shows a decrease of compressive strength and thermal conductivity by about 38.38% and 50.64% respectively. The decrease in dry density and thermal conductivity is related to the content of GOS, which is composed of organic and porous fibers. The GOS seems promising for improving the thermo-mechanical characteristics of CEB and which can also be used as reinforcement in CEBS.

Simulation of vibration piercing of pipe blank at press

2020 ◽  
Vol 76 (11) ◽  
pp. 1128-1138
Author(s):  
S. R. Rakhmanov
Keyword(s):  
High Frequency ◽  
Deformation Zone ◽  
Pipe Blank ◽  
Equipment Operation ◽  
Metal Deformation ◽  
Technological Tool ◽  
High Frequency Vibrations ◽  
Pipe Blanks ◽  
Wave Phenomena

In some cases, the processes of piercing or expanding pipe blanks involve the use of high-frequency active vibrations. However, due to insufficient knowledge, these processes are not widely used in the practice of seamless pipes production. In particular, the problems of increasing the efficiency of the processes of piercing or expanding a pipe blank at a piercing press using high-frequency vibrations are being solved without proper research and, as a rule, by experiments. The elaboration of modern technological processes for the production of seamless pipes using high-frequency vibrations is directly related to the choice of rational modes of metal deformation and the prediction resistance indicators of technological tools and the reliability of equipment operation. The creation of a mathematical model of the process of vibrating piercing (expansion) of an axisymmetric pipe blank at a piercing press of a pipe press facility is an actual task. A calculation scheme for the process of piercing a pipe plank has been elaborated. A dependence was obtained characterizing the speed of front of plastic deformation propagation on the speed of penetration of a vibrated axisymmetric mandrel into the pipe workpiece being pierced. The dynamic characteristics of the occurrence of wave phenomena in the metal being pierced under the influence of a vibrated tool have been determined, which significantly complements the previously known ideas about the stress-strain state of the metal in the deformation zone. The deformation fields in the zones of the disturbed region of the deformation zone were established, taking into account the high-frequency vibrations of the technological tool. It has been established that the choice of rational parameters (amplitude-frequency characteristics) of the vibration piercing process of a pipe blank results in significant increase in the efficiency of the process, the durability of the technological tool and the quality of the pierced blanks.

Sign in / Sign up

Export Citation Format

Share Document