Quasi-static compressive behavior of the ex-situ aluminum-alloy foam-filled tubes under elevated temperature conditions

2017 ◽  
Vol 206 ◽  
pp. 182-184 ◽  
Author(s):  
Nima Movahedi ◽  
Emanoil Linul
Materials ◽  
2018 ◽  
Vol 11 (4) ◽  
pp. 554 ◽  
Author(s):  
Emanoil Linul ◽  
Nima Movahedi ◽  
Liviu Marsavina

2016 ◽  
Vol 877 ◽  
pp. 393-399
Author(s):  
Jia Zhou ◽  
Jun Ping Zhang ◽  
Ming Tu Ma

This paper presents the main achievements of a research project aimed at investigating the applicability of the hot stamping technology to non heat treatable aluminium alloys of the 5052 H32 and heat treatable aluminium alloys of the 6016 T4P after six months natural aging. The formability and mechanical properties of 5052 H32 and 6016 T4P aluminum alloy sheets after six months natural aging under different temperature conditions were studied, the processing characteristics and potential of the two aluminium alloy at room and elevated temperature were investigated. The results indicated that the 6016 aluminum alloy sheet exhibit better mechanical properties at room temperature. 5052 H32 aluminum alloy sheet shows better formability at elevated temperature, and it has higher potential to increase formability by raising the temperature.


Author(s):  
Antoinette M. Maniatty ◽  
David J. Littlewood ◽  
Jing Lu

In order to better understand and predict the intragrain heterogeneous deformation in a 6063 aluminum alloy deformed at an elevated temperature, when additional slip systems beyond the usual octahedral slip systems are active, a modeling framework for analyzing representative polycrystals under these conditions is presented. A model polycrystal that has a similar microstructure to that observed in the material under consideration is modeled with a finite element analysis. A large number of elements per grain (more than 1000) are used to capture well the intragranular heterogeneous response. The polycrystal model is analyzed with three different sets of initial orientations. A compression test is used to calibrate the material model, and a macroscale simulation of the compression test is used to define the deformation history applied to the model polycrystal. In order to reduce boundary condition effects, periodic boundary conditions are applied to the model polycrystal. To investigate the effect of additional slip systems expected to be active at elevated temperatures, the results considering only the 12 {111}⟨110⟩ slip systems are compared to the results with the additional 12 {110}⟨110⟩ and {001}⟨110⟩ slip systems available (i.e., 24 available slip systems). The resulting predicted grain structure and texture are compared to the experimentally observed grain structure and texture in the 6063 aluminum alloy compression sample as well as to the available data in the literature, and the intragranular misorientations are studied.


1988 ◽  
pp. 200-205
Author(s):  
Shigenori Yamauchi ◽  
Kazuhisa Shibue ◽  
Hideo Sano ◽  
Kiyofumi Ito ◽  
Susumu Inumaru

Author(s):  
S Yaghoubi ◽  
F Fereshteh-Saniee

This research is concerned with the effects of the geometrical parameters of the die in elevated temperature Hydro-Mechanical Deep Drawing (HMDD) process of 2024 aluminum alloy. A Group Method of Data Handling (GMDH) process was used to train a neural network in order to study the process behavior. Based on the maximum reduction in sheet thickness and the uniformity of the final product, an objective function was constructed. The Bees Algorithm (BA) was used to achieve the optimal values for process variables. To verify the simulation results, they were compared with the experimental findings gained via this research and an appropriate correlation was observed between these results. This comparison showed that, by optimization of the geometrical parameters of the process, the value of the combined objective function was the best one compared with all of the cases tried in the present investigation.


2019 ◽  
Vol 12 (1) ◽  
pp. 40 ◽  
Author(s):  
Justyna Knapik-Kowalczuk ◽  
Krzysztof Chmiel ◽  
Karolina Jurkiewicz ◽  
Natália Correia ◽  
Wiesław Sawicki ◽  
...  

The purpose of this paper is to examine the physical stability as well as viscoelastic properties of the binary amorphous ezetimibe–simvastatin system. According to our knowledge, this is the first time that such an amorphous composition is prepared and investigated. The tendency toward re-crystallization of the amorphous ezetimibe–simvastatin system, at both standard storage and elevated temperature conditions, have been studied by means of X-ray diffraction (XRD). Our investigations have revealed that simvastatin remarkably improves the physical stability of ezetimibe, despite the fact that it works as a plasticizer. Pure amorphous ezetimibe, when stored at room temperature, begins to re-crystallize after 14 days after amorphization. On the other hand, the ezetimibe-simvastatin binary mixture (at the same storage conditions) is physically stable for at least 1 year. However, the devitrification of the binary amorphous composition was observed at elevated temperature conditions (T = 373 K). Therefore, we used a third compound to hinder the re-crystallization. Finally, both the physical stability as well as viscoelastic properties of the ternary systems containing different concentrations of the latter component have been thoroughly investigated.


Sign in / Sign up

Export Citation Format

Share Document