Hot corrosion behavior of dense CYSZ/YSZ bilayer coatings deposited by atmospheric plasma spray in Na2SO4 + V2O5 molten salts

2022 ◽  
pp. 128066
Author(s):  
Jhonattan de la Roche ◽  
Juan Manuel Alvarado-Orozco ◽  
Pablo Andrés Gómez ◽  
Irene García Cano ◽  
Sergi Dosta ◽  
...  
Keyword(s):  
Corrosion Behavior ◽  
Plasma Spray ◽  
Hot Corrosion ◽  
Molten Salts ◽  
Atmospheric Plasma Spray ◽  
Atmospheric Plasma ◽  
Bilayer Coatings

Fabrication and Ablation Behavior of Plasma Sprayed ZrC-W Composite Coatings

2014 ◽  
Vol 602-603 ◽  
pp. 552-555
Author(s):  
Dan Lu ◽  
Ya Ran Niu ◽  
Xue Lian Ge ◽  
Xue Bing Zheng ◽  
Guang Chen
Keyword(s):  
Thermal Conductivity ◽  
Thermal Shock ◽  
Plasma Spray ◽  
Composite Coatings ◽  
Lamellar Microstructure ◽  
Atmospheric Plasma Spray ◽  
Atmospheric Plasma ◽  
Plasma Flame ◽  
Plasma Sprayed ◽  
Zrc Coating

In this work, atmospheric plasma spray (APS) technology was applied to fabricate ZrC-W composite coatings. The microstructure of the composite coatings was characterized. The influence of W content on the ablation-resistant and thermal shock properties of ZrC-W composite coatings was evaluated using a plasma flame. The results show that the ZrC-W composite coatings had typically lamellar microstructure, which was mainly made up of cubic ZrC, cubic W and a small amount of tetragonal ZrO2. The ZrC-W coatings had improved ablation resistant and thermal shock properties compared with those of the pure ZrC coating. It was supposed that the improved density, thermal conductivity and toughness of the composite coatings contributed to this phenomenon.

scholarly journals Hot Corrosion Behavior of BaLa2Ti3O10 Thermal Barrier Ceramics in V2O5 and Na2SO4 + V2O5 Molten Salts

Coatings ◽  
2019 ◽  
Vol 9 (6) ◽  
pp. 351 ◽  
Author(s):  
Hui Liu ◽  
Jin Cai ◽  
Jihong Zhu
Keyword(s):  
Corrosion Behavior ◽  
Hot Corrosion ◽  
Molten Salts ◽  
Main Reaction ◽  
Thermal Barrier ◽  
Dense Layer ◽  
Reaction Products ◽  
Corrosion Medium ◽  
Barrier Coating ◽  
Salt Corrosion

BaLa2Ti3O10 ceramics for thermal barrier coating (TBC) applications were fabricated, and exposed to V2O5 and Na2SO4 + V2O5 molten salts at 900 °C to investigate the hot corrosion behavior. After 4 h corrosion tests, the main reaction products resulting from V2O5 salt corrosion were LaVO4, TiO2, and Ba3V4O13, whereas those due to Na2SO4 + V2O5 corrosion consisted of LaVO4, TiO2, BaSO4 and some Ba3V4O13. The structures of reaction layers on the surfaces depended on the corrosion medium. In V2O5 salt, the layer was dense and had a thickness of 8–10 μm. While in Na2SO4 + V2O5 salt, it had a ~15 μm porous structure and a dense, thin band at the bottom. Beneath the dense layer or the band, no obvious molten salt was found. The mechanisms by which the reaction layer forms were discussed.

scholarly journals Mechanical Properties of Strontium–Hardystonite–Gahnite Coating Formed by Atmospheric Plasma Spray

Coatings ◽  
2019 ◽  
Vol 9 (11) ◽  
pp. 759
Author(s):  
Duy Quang Pham ◽  
Christopher C. Berndt ◽  
Ameneh Sadeghpour ◽  
Hala Zreiqat ◽  
Peng-Yuan Wang ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Plastic Deformation ◽  
Plasma Spray ◽  
Elastic Moduli ◽  
Cell Attachment ◽  
Atmospheric Plasma Spray ◽  
Atmospheric Plasma ◽  
Wear Volume ◽  
Marrow Mesenchymal Stem Cells ◽  
Good Biocompatibility

In this work, we measured the mechanical properties and tested the cell viability of a bioceramic coating, strontium–hardystonite–gahnite (Sr–HT–G, Sr–Ca2ZnSi2O7–ZnAl2O4), to evaluate potential use of this novel bioceramic for bone regeneration applications. The evaluation of Sr–HT–G coatings deposited via atmospheric plasma spray (APS) onto Ti–6Al–4V substrates have been contrasted to the properties of the well-known commercial standard coating of hydroxyapatite (HAp: Ca10(PO4)6(OH)2). The Sr–HT–G coating exhibited uniform distribution of hardness and elastic moduli across its cross-section; whereas the HAp coating presented large statistical variations of these distributions. The Sr–HT–G coating also revealed higher results of microhardness, nanohardness and elastic moduli than those shown for the HAp coating. The nanoscratch tests for the Sr–HT–G coating presented a low volume of material removal without high plastic deformation, while the HAp coating revealed ploughing behaviour with a large pileup of materials and plastic deformation along the scratch direction. Furthermore, nanoscanning wear tests indicated that Sr–HT–G had a lower wear volume than the HAp coating. The Sr–HT–G coating had slightly higher cell attachment density and spreading area compared to the HAp coating indicating that both coatings have good biocompatibility for bone marrow mesenchymal stem cells (BMSCs).

Sign in / Sign up

Export Citation Format

Share Document