Aerodynamic study of single corrugated variable-camber morphing aerofoil concept

2021 ◽  
pp. 1-29
Author(s):  
K. Dhileep ◽  
D. Kumar ◽  
P.N. Gautham Vigneswar ◽  
P. Soni ◽  
S. Ghosh ◽  
...  
Keyword(s):  
Finite Volume ◽  
Interpolation Method ◽  
Beam Theory ◽  
Small Deformation ◽  
Aerodynamic Characteristics ◽  
Ansys Fluent ◽  
Aerodynamic Efficiency ◽  
Finite Element Software ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Abstract Camber morphing is an effective way to control the lift generated by any aerofoil and potentially improve the range (as measured by the lift-to-drag ratio) and endurance (as measured by $C_l^{3/2}/C_d$ ). This can be especially useful for fixed-wing Unmanned Aerial Vehicles (UAVs) undergoing different flying manoeuvres and flight phases. This work investigates the aerodynamic characteristics of the NACA0012 aerofoil morphed using a Single Corrugated Variable-Camber (SCVC) morphing approach. Structural analysis and morphed shapes are obtained based on small-deformation beam theory using chain calculations and validated using finite-element software. The aerofoil is then reconstructed from the camber line using a Radial Basis Function (RBF)-based interpolation method (J.H.S. Fincham and M.I. Friswell, “Aerodynamic optimisation of a camber morphing aerofoil,” Aerosp. Sci. Technol., 2015). The aerodynamic analysis is done by employing two different finite-volume solvers (OpenFOAM and ANSYS-Fluent) and a panel method code (XFoil). Results reveal that the aerodynamic coefficients predicted by the two finite-volume solvers using a fully turbulent flow assumption are similar but differ from those predicted by XFoil. The aerodynamic efficiency and endurance factor of morphed aerofoils indicate that morphing is beneficial at moderate to high lift requirements. Further, the optimal morphing angle increases with an increase in the required lift. Finally, it is observed for a fixed angle-of-attack that an optimum morphing angle exists for which the aerodynamic efficiency becomes maximum.

scholarly journals Computational Investigation of Aerodynamic Characteristics for Elliptic UAVs’ Wing

2018 ◽  
Vol 6 (3) ◽  
Author(s):  
Amaal Attiah ◽  
Ibrahim Elbadawy ◽  
Osama E. Mahmoud
Keyword(s):  
Reynolds Number ◽  
Computational Study ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Thickness Ratio ◽  
Ansys Fluent ◽  
Rotor Wing ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Elliptic Airfoil

Unmanned Aerial Vehicles, UAVs, gained an important role in modern military and civilian applications. Developments in UAVs technology improve its performance and maneuverability with acceptable cost. Elliptic airfoil had been widely used in the development of Rotor/Wing subsonic aircraft. The present work aims to investigate the effect of various elliptic airfoil parameters, such as Reynolds number, angle of attack and airfoil thickness, on aerodynamic behavior using two-dimensional computational study. The computational results were validated by experimental results. Angles of attack was evaluated from 0° to 18° in order to analyze aerodynamic characteristics up to stall condition, while Reynolds number was evaluated at values of 1×10⁵, 3×105, 2×106, and 8×106, to cover the range of rotary and fixed wing flight conditions. Thickness ratio was ranged from 5% to 25% to include the UAVs airfoil thicknesses so that choice best thickness gets max lift to drag ratio. In addition, the thicknesses location was evaluated for a range of 30% to 70% to get suitable location gets max left to drag ratio. The ANSYS-Fluent software was used with Spalart-Allmaras turbulence model, and found that the maximum lift to drag ratio which improve the UAV capability in this study is at Re=2×106, angle of attack at 8°, max thickness ratio of (0.1chord) located at (0.3chord).

scholarly journals Experimental Investigation of a Wing-in-Ground Effect Craft

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
M. Mobassher Tofa ◽  
Adi Maimun ◽  
Yasser M. Ahmed ◽  
Saeed Jamei ◽  
Agoes Priyanto ◽  
...  
Keyword(s):  
Research Work ◽  
Ground Effect ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Efficiency ◽  
Ground Clearance ◽  
Drag Forces ◽  
Lift And Drag ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Wing In Ground Effect

The aerodynamic characteristics of the wing-in-ground effect (WIG) craft model that has a noble configuration of a compound wing was experimentally investigated and Universiti Teknologi Malaysia (UTM) wind tunnel with and without endplates. Lift and drag forces, pitching moment coefficients, and the centre of pressure were measured with respect to the ground clearance and the wing angle of attack. The ground effect and the existence of the endplates increase the wing lift-to-drag ratio at low ground clearance. The results of this research work show new proposed design of the WIG craft with compound wing and endplates, which can clearly increase the aerodynamic efficiency without compromising the longitudinal stability. The use of WIG craft is representing an ambitious technology that will help in reducing time, effort, and money of the conventional marine transportation in the future.

scholarly journals Aerodynamic and Vibration Characteristics of the Micro-Octocopter at Low Reynolds Number

2021 ◽  
Vol 2021 ◽  
pp. 1-9
Author(s):  
Xiaohua Zou ◽  
Mingsheng Ling ◽  
Wenzheng Zhai
Keyword(s):  
Reynolds Number ◽  
Load Capacity ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Vibration Characteristics ◽  
Low Reynolds ◽  
Vibration Performance ◽  
Drag Ratio ◽  
Lift To Drag Ratio

With the development of flight technology, the need for stable aerodynamic and vibration performance of the aircraft in the civil and military fields has gradually increased. In this case, the requirements for aerodynamic and vibration characteristics of the aircraft have also been strengthened. The existing four-rotor aircraft carries limited airborne equipment and payload, while the current eight-rotor aircraft adopts a plane layout. The size of the propeller is generally fixed, including the load capacity. The upper and lower tower layout analyzed in this paper can effectively solve the problems of insufficient four-axis load and unstable aerodynamic and vibration performance of the existing eight-axis aircraft. This paper takes the miniature octorotor as the research object and studies the aerodynamic characteristics of the miniature octorotor at different low Reynolds numbers, different air pressures and thicknesses, and the lift coefficient and lift-to-drag ratio, as well as the vibration under different elastic moduli and air pressure characteristics. The research algorithm adopted in this paper is the numerical method of fluid-solid cohesion and the control equation of flow field analysis. The research results show that, with the increase in the Reynolds number within a certain range, the aerodynamic characteristics of the miniature octorotor gradually become better. When the elastic modulus is 2.5 E, the aircraft’s specific performance is that the lift increases, the critical angle of attack increases, the drag decreases, the lift-to-drag ratio increases significantly, and the angle of attack decreases. However, the transition position of the flow around the airfoil surface is getting closer to the leading edge, and its state is more likely to transition from laminar flow to turbulent flow. When the unidirectional carbon fiber-reinforced thickness is 0.2 mm and the thin arc-shaped airfoil with the convex structure has a uniform thickness of 2.5% and a uniform curvature of 4.5%, the aerodynamic and vibration characteristics of the octorotor aircraft are most beneficial to flight.

Aerodynamic characteristics of breathing blunt nose configuration at hypersonic speeds

2016 ◽  
Vol 231 (5) ◽  
pp. 840-858 ◽  
Author(s):  
Yasumasa Watanabe ◽  
Kojiro Suzuki ◽  
Ethirajan Rathakrishnan
Keyword(s):  
Lift Coefficient ◽  
Aerodynamic Characteristics ◽  
The Body ◽  
Positive Pressure ◽  
Stagnation Region ◽  
Total Drag ◽  
Hypersonic Speeds ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Blunt Nose

Breathing blunt nose technique is one of the promising methods for reducing the drag of blunt-nosed body at hypersonic speeds. The air, traversed by the bow shock positioned ahead of the nose, at the stagnation region is allowed to enter through a hole at the blunt-nose and ejected at the rear part (base region) of the body. This manipulation reduces the positive pressure over the stagnation regions of the nose and increases the pressure at the base, resulting in reduced suction at the base. The simultaneous manifestation of reducing the compression at the nose and suction at the base regions results in reduction of the total drag. The drag reduction caused by the breathing blunt nose technique has been measured in a Mach 7 tunnel. Also, the drag and flow field around the blunt-nosed body, with and without breathing hole, has been computed. The aerodynamic characteristics of the breathing blunt nose model obtained experimentally are compared with the CFD results. It is found that the breathing results in 5% reduction in drag. The lift coefficient also comes down for the model with breathing nose. But the lift-to-drag ratio is found to be the same for both the cases; the blunt-nosed body with and without nose-hole.

420 Aerodynamic Characteristics and Flow Field of High Lift-to-drag Ratio Airfoils in Low Reynolds Number

2015 ◽  
Vol 2015.68 (0) ◽  
pp. 167-168 ◽  
Author(s):  
Takahiro MAKIZONO ◽  
Gaku SASAKI ◽  
Hiroshi OCHI ◽  
Takaaki MATSUMOTO ◽  
Koichi YONEMOTO
Keyword(s):  
Reynolds Number ◽  
Flow Field ◽  
Low Reynolds Number ◽  
Aerodynamic Characteristics ◽  
High Lift ◽  
Low Reynolds ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Based on Imitation Seagull Airfoil UVA Wing Numerical Simulation

2012 ◽  
Vol 271-272 ◽  
pp. 791-796
Author(s):  
Xin Hua ◽  
Wei Shao ◽  
Chun Hua Zhang ◽  
Zhi Qiang Zhang
Keyword(s):  
Numerical Simulation ◽  
High Performance ◽  
Lift Coefficient ◽  
Wind Tunnel Test ◽  
Aerodynamic Characteristics ◽  
Wing Scale ◽  
Fluent Software ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Straight Wing

Wing aircraft is one of the major components to generate lift, in today's energy shortage, design the high lift-to-drag ratio wing is the goal pursued by, The author in the exploration of bionic airfoil aerodynamic characteristics on the basis of, which will be applied to straight wing design so as to improve the aerodynamic performance of aircraft.Our research mainly includes two aspects: first, the use of imitation seagull airfoil and NACA4412 airfoil are designed into the straight wing. The use of FLUENT software in Re=300000condition carries on the numerical simulation results show that the ratio of gull wing airfoil than NACA4412 lift coefficient increased by 13%, while the lift to drag ratio,is improved by 46.83%. Then, using the similarity principle, the wing scale, was tested in a wind tunnel test, the results obtained with the simulation are consistent. Airfoil design for the design of high performance wing opened a new way.

scholarly journals Boundary Layer Control of Airfoil using Rotating Cylinder

2020 ◽  
Vol 8 (6) ◽  
pp. 4742-4750
Keyword(s):  
Leading Edge ◽  
Rotating Cylinder ◽  
Aerodynamic Characteristics ◽  
Favourable Result ◽  
Ansys Fluent ◽  
High Lift ◽  
Freestream Velocity ◽  
Aerodynamic Efficiency ◽  
Two Parameters ◽  
Layer Control

The requirement for improving the aerodynamic efficiency and delaying the formation of stall over the wing has been of prime importance within the field of aviation. The main objective of the project is to further improve upon these two parameters. The configuration used for analysis consists of a NACA 2412 airfoil of chord length 0.982m with a 64mm cylinder at the leading edge. Analysis is completed using ANSYS Fluent, with a freestream velocity of 10m/s. The aerodynamic characteristics of three configuration bare airfoil, Airfoil with static cylinder and Airfoil with rotating cylinder are tabulated and plotted. The comparison is then followed by pressure and velocity contours to visualize the flow over each configuration. The rotating cylinder configuration shows a improvement in the aerodynamics characteristics. The rotating cylinder configuration gives the most favourable result. This study has a potential application in high lift devices and can be used as stall delaying device

Analysis of UAS-S4 Éhecatl aerodynamic performance improvement using several configurations of a morphing wing technology

2016 ◽  
Vol 120 (1231) ◽  
pp. 1337-1364 ◽  
Author(s):  
O. Şugar Gabor ◽  
A. Koreanschi ◽  
R.M. Botez
Keyword(s):  
Aerodynamic Characteristics ◽  
Morphing Wing ◽  
Flow Solver ◽  
Bee Colony ◽  
Gradient Based ◽  
Search Routine ◽  
Drag Ratio ◽  
Lifting Line ◽  
Lift To Drag Ratio ◽  
Lifting Line Method

ABSTRACTThe paper presents the results of the aerodynamic optimisation of an Unmanned Aerial System's wing using a morphing approach. The shape deformation of the wing is achieved by placing actuator lines at several positions along its span. For each flight condition, the optimal displacements are found by using a combination of the new Artificial Bee Colony algorithm and a classical gradient-based search routine. The wing aerodynamic characteristics are calculated with an efficient nonlinear lifting line method coupled with a two-dimensional viscous flow solver. The optimisations are performed at angles of attack below the maximum lift angle, with the aim of improving the Hydra Technologies UAS-S4 wing lift-to-drag ratio. Several configurations of the morphing wing are proposed, each with a different number of actuation lines, and the improvements obtained by these configurations are analysed and compared.

scholarly journals Aerodynamic Optimization of an Over-the-Wing-Nacelle-Mount Configuration

2011 ◽  
Vol 2011 ◽  
pp. 1-13 ◽  
Author(s):  
Daisuke Sasaki ◽  
Kazuhiro Nakahashi
Keyword(s):  
Interference Effect ◽  
Jet Engines ◽  
Aerodynamic Design ◽  
Aerodynamic Optimization ◽  
High Lift ◽  
Aerodynamic Efficiency ◽  
Wing Geometry ◽  
Aerodynamic Interference ◽  
Drag Ratio ◽  
Lift To Drag Ratio

An over-the-wing-nacelle-mount airplane configuration is known to prevent the noise propagation from jet engines toward ground. However, the configuration is assumed to have low aerodynamic efficiency due to the aerodynamic interference effect between a wing and a nacelle. In this paper, aerodynamic design optimization is conducted to improve aerodynamic efficiency to be equivalent to conventional under-the-wing-nacelle-mount configuration. The nacelle and wing geometry are modified to achieve high lift-to-drag ratio, and the optimal geometry is compared with a conventional configuration. Pylon shape is also modified to reduce aerodynamic interference effect. The final wing-fuselage-nacelle model is compared with the DLR F6 model to discuss the potential of Over-the-Wing-Nacelle-Mount geometry for an environmental-friendly future aircraft.

Optimization of Maximum Lift to Drag Ratio on Airfoil Design Based on Artificial Neural Network Utilizing Genetic Algorithm

2014 ◽  
Vol 493 ◽  
pp. 123-128 ◽  
Author(s):  
Ismoyo Haryanto ◽  
Tony Suryo Utomo ◽  
Nazaruddin Sinaga ◽  
Citra Asti Rosalia ◽  
Aditya Pratama Putra
Keyword(s):  
Neural Network ◽  
Genetic Algorithm ◽  
Artificial Neural Network ◽  
Design Method ◽  
Aerodynamic Characteristics ◽  
Drag Coefficients ◽  
Artificial Neural ◽  
Lift And Drag ◽  
Drag Ratio ◽  
Lift To Drag Ratio

.This paper deals with an alternative design method of airfoil for wind turbine blade for low wind speed based on combination of smart computing and numerical optimization. In this work, a simulation of Artificial Neural Network (ANN) for determining the relation between airfoil geometry and its aerodynamic characteristics was conducted. First, several airfoil geometries were generated through transformation of complex variables (Joukowski transformation), and then lift and drag coefficients of each airfoil were determined using CFD (Computational Fluid Dynamics). In present study, the ANN training was conducted using airfoil geometry and its aerodynamic characteristics as input and output, respectively. Therefore, lift and drag coefficients can be directly determined only by giving the airfoil geometry without having to perform wind tunnel experiment or numerical computation. Moreover, the optimization was conducted to obtain an airfoil geometry which gives maximum lift to drag ratio (CL/CD) for specific Reynolds number. For this purpose Genetic Algorithm (GA) was applied as optimizer. The results were validated using commercial CFD and it can be shown that the result are satisfactory with error approximately of 6%.

Sign in / Sign up

Export Citation Format

Share Document