scholarly journals Experimental Investigation of a Wing-in-Ground Effect Craft

2014 ◽  
Vol 2014 ◽  
pp. 1-7 ◽  
Author(s):  
M. Mobassher Tofa ◽  
Adi Maimun ◽  
Yasser M. Ahmed ◽  
Saeed Jamei ◽  
Agoes Priyanto ◽  
...  
Keyword(s):  
Research Work ◽  
Ground Effect ◽  
Aerodynamic Characteristics ◽  
Aerodynamic Efficiency ◽  
Ground Clearance ◽  
Drag Forces ◽  
Lift And Drag ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Wing In Ground Effect

The aerodynamic characteristics of the wing-in-ground effect (WIG) craft model that has a noble configuration of a compound wing was experimentally investigated and Universiti Teknologi Malaysia (UTM) wind tunnel with and without endplates. Lift and drag forces, pitching moment coefficients, and the centre of pressure were measured with respect to the ground clearance and the wing angle of attack. The ground effect and the existence of the endplates increase the wing lift-to-drag ratio at low ground clearance. The results of this research work show new proposed design of the WIG craft with compound wing and endplates, which can clearly increase the aerodynamic efficiency without compromising the longitudinal stability. The use of WIG craft is representing an ambitious technology that will help in reducing time, effort, and money of the conventional marine transportation in the future.

Aerodynamic study of single corrugated variable-camber morphing aerofoil concept

2021 ◽  
pp. 1-29
Author(s):  
K. Dhileep ◽  
D. Kumar ◽  
P.N. Gautham Vigneswar ◽  
P. Soni ◽  
S. Ghosh ◽  
...  
Keyword(s):  
Finite Volume ◽  
Interpolation Method ◽  
Beam Theory ◽  
Small Deformation ◽  
Aerodynamic Characteristics ◽  
Ansys Fluent ◽  
Aerodynamic Efficiency ◽  
Finite Element Software ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Abstract Camber morphing is an effective way to control the lift generated by any aerofoil and potentially improve the range (as measured by the lift-to-drag ratio) and endurance (as measured by $C_l^{3/2}/C_d$ ). This can be especially useful for fixed-wing Unmanned Aerial Vehicles (UAVs) undergoing different flying manoeuvres and flight phases. This work investigates the aerodynamic characteristics of the NACA0012 aerofoil morphed using a Single Corrugated Variable-Camber (SCVC) morphing approach. Structural analysis and morphed shapes are obtained based on small-deformation beam theory using chain calculations and validated using finite-element software. The aerofoil is then reconstructed from the camber line using a Radial Basis Function (RBF)-based interpolation method (J.H.S. Fincham and M.I. Friswell, “Aerodynamic optimisation of a camber morphing aerofoil,” Aerosp. Sci. Technol., 2015). The aerodynamic analysis is done by employing two different finite-volume solvers (OpenFOAM and ANSYS-Fluent) and a panel method code (XFoil). Results reveal that the aerodynamic coefficients predicted by the two finite-volume solvers using a fully turbulent flow assumption are similar but differ from those predicted by XFoil. The aerodynamic efficiency and endurance factor of morphed aerofoils indicate that morphing is beneficial at moderate to high lift requirements. Further, the optimal morphing angle increases with an increase in the required lift. Finally, it is observed for a fixed angle-of-attack that an optimum morphing angle exists for which the aerodynamic efficiency becomes maximum.

scholarly journals Stress and Shape Analysis of a Paraglider Wing

1965 ◽  
Vol 32 (4) ◽  
pp. 771-780 ◽  
Author(s):  
Robert W. Fralich
Keyword(s):  
Structural Analysis ◽  
Shape Analysis ◽  
Numerical Results ◽  
Internal Stresses ◽  
Flexible Wing ◽  
Aerodynamic Pressure ◽  
Drag Forces ◽  
Lift And Drag ◽  
Drag Ratio ◽  
Lift To Drag Ratio

A combined aerodynamic-structural analysis is made which is based on the assumption that the sail is flexible and has freedom to take the shape which the aerodynamic pressure and the internal stresses dictate. Numerical results were obtained for Newtonian impact aerodynamic theory and were compared with published results obtained for a rigid idealization of the paraglider wing. It was found that the assumed rigid idealization did not approximate the shape of a flexible wing well and led to significant errors in the lift and drag forces and the lift-to-drag ratio. The new calculations provide a basis for design of paragliders for hypersonic flight.

scholarly journals Aerodynamic Performance of Biomimicry Snake-Shaped Airfoil

2019 ◽  
Vol 9 (2) ◽  
pp. 3319-3323
Keyword(s):  
Cross Section ◽  
Lift Coefficient ◽  
Design Parameters ◽  
Drag Forces ◽  
Cross Section Shape ◽  
Section Shape ◽  
Wide Range ◽  
Lift And Drag ◽  
Drag Ratio ◽  
Lift To Drag Ratio

The cross-section shape and proportionality between geometrical dimensions are the most important design parameters of any lifting surfaces. These parameters affect the amount of the aerodynamic forces that will be generated. In this study, the focus is placed on the snake-cross-section airfoil known as the S-airfoil. It is found that there is a lack of available researches on S-airfoil despite its important characteristics. A parametric study on empty model of the S-airfoil with a cross-section shape that is inspired by the Chrysopelea paradise snake is conducted through numerical simulation. Simulation using 2D-ANSYS FLUENT17 software is used to generate the lift and drag forces to determine the performance of airfoil aerodynamic. Based on the results, the S-airfoil can be improved in performance of aerodynamic by reducing the thickness at certain range, whereby changing the thickness-to-chord ratio from 0.037 to 0.011 results in the increment of lift-to-drag ratio from 2.629 to 3.257. On other hand, increasing the height-to-chord ratio of the S-airfoil will increase maximum lift coefficient but drawback is a wide range of angles of attack regarding maximum lift-to-drag ratio. Encouraging results obtained in this study draws attention to the importance of expanding the research on S-airfoil and its usage, especially in wind energy.

Static Stability of a Compound Wing Configuration in Ground Effect

2014 ◽  
Vol 69 (7) ◽  
Author(s):  
Saeed Jamei ◽  
Adi Maimun ◽  
M. Mobassher Tofa ◽  
Nor Azwadi ◽  
Shuhaimi Mansor ◽  
...  
Keyword(s):  
Experimental Data ◽  
Deep Understanding ◽  
Ground Effect ◽  
Static Stability ◽  
Main Concern ◽  
Turbulent Model ◽  
The Stability ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Wing In Ground Effect

The height static stability of a wing can be a main concern for conceptual design of wing-in-ground effect (WIG) crafts. In this research, the stability of a rectangular and compound wing was computationally predicted in ground effect. A realizable k-ε turbulent model was used for simulation the flow filed over the wing surfaces. First, the drag coefficient and lift to drag ratio of numerical simulation were validated by experimental data of the rectangular wing. Next, the stability of the compound wing respect to different ground clearances will be determined and compared with rectangular wing. This study illustrated a deep understanding of static stability of present compound wing in ground effect, which eventually can be a guideline for researchers and designers of WIG craft.

Optimization of Maximum Lift to Drag Ratio on Airfoil Design Based on Artificial Neural Network Utilizing Genetic Algorithm

2014 ◽  
Vol 493 ◽  
pp. 123-128 ◽  
Author(s):  
Ismoyo Haryanto ◽  
Tony Suryo Utomo ◽  
Nazaruddin Sinaga ◽  
Citra Asti Rosalia ◽  
Aditya Pratama Putra
Keyword(s):  
Neural Network ◽  
Genetic Algorithm ◽  
Artificial Neural Network ◽  
Design Method ◽  
Aerodynamic Characteristics ◽  
Drag Coefficients ◽  
Artificial Neural ◽  
Lift And Drag ◽  
Drag Ratio ◽  
Lift To Drag Ratio

.This paper deals with an alternative design method of airfoil for wind turbine blade for low wind speed based on combination of smart computing and numerical optimization. In this work, a simulation of Artificial Neural Network (ANN) for determining the relation between airfoil geometry and its aerodynamic characteristics was conducted. First, several airfoil geometries were generated through transformation of complex variables (Joukowski transformation), and then lift and drag coefficients of each airfoil were determined using CFD (Computational Fluid Dynamics). In present study, the ANN training was conducted using airfoil geometry and its aerodynamic characteristics as input and output, respectively. Therefore, lift and drag coefficients can be directly determined only by giving the airfoil geometry without having to perform wind tunnel experiment or numerical computation. Moreover, the optimization was conducted to obtain an airfoil geometry which gives maximum lift to drag ratio (CL/CD) for specific Reynolds number. For this purpose Genetic Algorithm (GA) was applied as optimizer. The results were validated using commercial CFD and it can be shown that the result are satisfactory with error approximately of 6%.

Ground Effect on the Vortex Flow and Aerodynamics of a Slender Delta Wing

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
T. Lee ◽  
L. S. Ko
Keyword(s):  
Vortex Breakdown ◽  
Delta Wing ◽  
Leading Edge ◽  
Ground Effect ◽  
Drag Forces ◽  
Wing Chord ◽  
Ground Distance ◽  
Lift And Drag ◽  
Wing Stall ◽  
Wing In Ground Effect

The ground effect on the aerodynamic loading and leading-edge vortex (LEV) flow generated by a slender delta wing was investigated experimentally. Both the lift and drag forces were found to increase with reducing ground distance (up to 50% of the wing chord). The lift increment was also found to be the greatest at low angles of attack α and decreased rapidly with increasing ground distance and α. The ground effect-caused earlier wing stall was also accompanied by a strengthened LEV with an increased rotational speed and size compared to the baseline wing. The smaller the ground distance, the stronger the LEV and the earlier vortex breakdown became. Meanwhile, the vortex trajectory was also found to be located further inboard and above the delta wing in ground effect compared to its baseline-wing counterpart. Finally, for wing-in-ground effect (WIG) craft with delta-wing planform the most effective in-ground-effect flight should be kept within 10% of the wing chord.

scholarly journals Lift and Drag Coefficient Map of NACA4415 Airfoil

2021 ◽  
Vol 2076 (1) ◽  
pp. 012066
Author(s):  
Rui Yin ◽  
Jing Huang ◽  
Zhi-Yuan He
Keyword(s):  
Reynolds Number ◽  
Drag Coefficient ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Optimal Angle ◽  
Fluent Software ◽  
Lift And Drag ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Abstract The NACA4415 airfoil was numerically simulated with the help of the Fluent software to analyze its aerodynamic characteristics. Results are acquired as follows: The calculation accuracy of Fluent software is much higher than that of XFOIL software; the calculation result of SST k-ω(sstkw) turbulence model is closest to the experimental value; within a certain range, the larger the Reynolds number is, the larger the lift coefficient and lift-to-drag ratio of the airfoil will be, and the smaller the drag coefficient will be; when the angle of attack is less than the optimal angle of attack, the Reynolds number has less influence on the lift-to-drag coefficient and the lift-to-drag ratio; as the Reynolds number increases, the optimal angle of attack increases slightly, and the applicable angle of attack range for high lift-to-drag ratios becomes smaller.

scholarly journals Effects of Pitching Motion Elements on Aerodynamic Characteristics of Airfoil

2021 ◽  
Vol 2076 (1) ◽  
pp. 012078
Author(s):  
Rui Yin ◽  
Jing Huang ◽  
Zhi-Yuan He
Keyword(s):  
Drag Coefficient ◽  
Lift Coefficient ◽  
Angle Of Attack ◽  
Aerodynamic Characteristics ◽  
Initial Angle ◽  
Pitching Motion ◽  
The Difference ◽  
Lift And Drag ◽  
Drag Ratio ◽  
Lift To Drag Ratio

Abstract The aerodynamic characteristics of NACA4412 airfoil with different pitching motion elements were compared and analyzed based on CFD in this research. The results are acquired as follows: the difference between the lift and drag coefficients of the airfoil during pitch up and pitch down motions becomes larger with the increase of the pitching amplitude or initial angle of attack; as the pitching amplitude increases, the lift coefficient grows slightly greater and the drag coefficient grows much greater; as the initial angle of attack increases, the lift coefficient grows much greater and the drag coefficient grows slightly; the smaller the attenuation frequency is, the larger the lift-to-drag ratio of the airfoil will be.

Ground effect on a slender reverse delta wing with anhedral

2018 ◽  
Vol 233 (4) ◽  
pp. 1516-1525
Author(s):  
T Lee ◽  
V Tremblay-Dionne ◽  
LS Ko
Keyword(s):  
Rotational Speed ◽  
Delta Wing ◽  
Ground Effect ◽  
Drag Coefficients ◽  
Drag Forces ◽  
Trailing Edges ◽  
Lift And Drag ◽  
Total Circulation ◽  
Wing In Ground Effect

The ground effect on the lift and drag forces and vortices generated by a slender reverse delta wing with different anhedrals was investigated experimentally. The study was inspired by the Lippisch-type RFB X-114 WIG (wing-in-ground effect) craft for which a reverse delta wing planform with anhedral was employed. The results show that, by positioning the trailing edges of the anhedraled reverse delta wing parallel to the ground, the lift and drag coefficients were found to increase persistently with increasing anhedral as the ground was approached (for ground distances within 40% chord). The observed lift augmentation was also accompanied by an ever-increasing rotational speed and total circulation of the vortices generated by the anhedraled wing. The vortices were also found to be displaced more outboard as the ground was approached, which further suggests their little relevance to the lift generation of the anhedraled reverse delta wing.

scholarly journals Water Energy Resource Innovation on the Cavitation Characteristics

2020 ◽  
Vol 143 (2) ◽  
Author(s):  
Mohammad D. Qandil ◽  
Ahmad I. Abbas ◽  
Tarek ElGammal ◽  
Ahmad I. Abdelhadi ◽  
Ryoichi S. Amano
Keyword(s):  
Volume Fraction ◽  
Energy Resource ◽  
Inverse Correlation ◽  
Cavitation Number ◽  
Drag Forces ◽  
Lift And Drag ◽  
Work Done ◽  
Drag Ratio ◽  
Lift To Drag Ratio ◽  
Upstream Flow

Abstract The main purpose of this study is to numerically correlate the amount of generated vapor over a hydrofoil to the lift and drag coefficients acting on it. Cavitation characteristics were investigated of a hydrofoil in the cavitating, sub-cavitating, and non-cavitating flows for different angles of attacks (AoA) with the high upstream flow velocity. The hydrofoil was tested in a square water tunnel with water entering the tunnel at various velocities for each AoA ranges from 9.1 m/s to 12.2 m/s. It was found that lift and drag forces acting on the hydrofoil follow the trend of the experimental data quite closely. While the cavitation can be identified by a unique number (averaged vapor volume fraction), the work done created an inverse correlation between this number and the cavitation number at the same angle of attack. The lift force declines with the increase in the vapor content on the hydrofoil surface, meanwhile the drag force peaks at certain vapor volume fraction, and then, a huge reduction occurs with the considerable decrease in the corresponding cavitation number. A fourth-order correlation generated between the lift to drag (L/D) and the cavitation number (σ). It was found the lift-to-drag ratio decreases by the formation of the cavitation over the hydrofoil, thus causing a drop in the efficiency of the turbomachines.

Sign in / Sign up

Export Citation Format

Share Document