The Isobars in Boundary Layers at Supersonic Speeds

1968 ◽  
Vol 19 (2) ◽  
pp. 105-126 ◽  
Author(s):  
D. F. Myring ◽  
A. D. Young
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Equations Of Motion ◽  
Normal Pressure ◽  
Simple Extension ◽  
Pressure Gradients ◽  
Boundary Layer Flows ◽  
Hyperbolic Flow ◽  
The Individual ◽  
Momentum Integral

SummaryFor boundary layer flows over curved surfaces at moderately high supersonic speeds the existence of normal pressure gradients within the boundary layer becomes important even for small curvatures and they cannot be ignored. The describing equations are basically parabolic in form so that the simplifications inherent in hyperbolic flows would not at first sight seem to be relevant. However, the equations of motion for a two-dimensional, supersonic, rotational, viscous flow are analysed along the lines of a hyperbolic flow and the individual effects of viscosity and vorticity are examined with regard to the isobar distributions. It is found that these two properties have compensating effects and the experimental evidence presented confirms the conclusion that inside the boundary layer the isobars follow much the same rules as those which determine the isobars in the external hyperbolic flow. Since for turbulent boundary layers the fullness of the Mach number profile produces almost linear Mach lines in the boundary layer, this provides a simple extension to the methods of analysis, and the momentum integral equation is reformulated using a swept element bounded by linear isobars. The final equation is similar in form to the conventional one except that the momentum and displacement thicknesses are now defined by integrals along the swept isobars, and all normal pressure gradients due to centrifugal effects are accounted for.

The Departure from Equilibrium of Turbulent Boundary Layers

1968 ◽  
Vol 19 (1) ◽  
pp. 1-19 ◽  
Author(s):  
H. McDonald
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Kinetic Energy ◽  
Stress Distribution ◽  
Boundary Layers ◽  
Turbulent Boundary Layers ◽  
Two Dimensional ◽  
Pressure Distributions ◽  
Momentum Integral ◽  
State Examination

SummaryRecently two authors, Nash and Goldberg, have suggested, intuitively, that the rate at which the shear stress distribution in an incompressible, two-dimensional, turbulent boundary layer would return to its equilibrium value is directly proportional to the extent of the departure from the equilibrium state. Examination of the behaviour of the integral properties of the boundary layer supports this hypothesis. In the present paper a relationship similar to the suggestion of Nash and Goldberg is derived from the local balance of the kinetic energy of the turbulence. Coupling this simple derived relationship to the boundary layer momentum and moment-of-momentum integral equations results in quite accurate predictions of the behaviour of non-equilibrium turbulent boundary layers in arbitrary adverse (given) pressure distributions.

The Effects of Adverse Pressure Gradients on Momentum and Thermal Structures in Transitional Boundary Layers: Part 2—Fluctuation Quantities

1996 ◽  
Vol 118 (4) ◽  
pp. 728-736 ◽  
Author(s):  
S. P. Mislevy ◽  
T. Wang
Keyword(s):  
Boundary Layer ◽  
Shear Stress ◽  
Transition Region ◽  
Boundary Layers ◽  
Reynolds Shear Stress ◽  
Turbulent Shear ◽  
Wall Region ◽  
Pressure Gradients ◽  
Baseline Case ◽  
Near Wall

The effects of adverse pressure gradients on the thermal and momentum characteristics of a heated transitional boundary layer were investigated with free-stream turbulence ranging from 0.3 to 0.6 percent. Boundary layer measurements were conducted for two constant-K cases, K1 = −0.51 × 10−6 and K2 = −1.05 × 10−6. The fluctuation quantities, u′, ν′, t′, the Reynolds shear stress (uν), and the Reynolds heat fluxes (νt and ut) were measured. In general, u′/U∞, ν′/U∞, and νt have higher values across the boundary layer for the adverse pressure-gradient cases than they do for the baseline case (K = 0). The development of ν′ for the adverse pressure gradients was more actively involved than that of the baseline. In the early transition region, the Reynolds shear stress distribution for the K2 case showed a near-wall region of high-turbulent shear generated at Y+ = 7. At stations farther downstream, this near-wall shear reduced in magnitude, while a second region of high-turbulent shear developed at Y+ = 70. For the baseline case, however, the maximum turbulent shear in the transition region was generated at Y+ = 70, and no near-wall high-shear region was seen. Stronger adverse pressure gradients appear to produce more uniform and higher t′ in the near-wall region (Y+ < 20) in both transitional and turbulent boundary layers. The instantaneous velocity signals did not show any clear turbulent/nonturbulent demarcations in the transition region. Increasingly stronger adverse pressure gradients seemed to produce large non turbulent unsteadiness (or instability waves) at a similar magnitude as the turbulent fluctuations such that the production of turbulent spots was obscured. The turbulent spots could not be identified visually or through conventional conditional-sampling schemes. In addition, the streamwise evolution of eddy viscosity, turbulent thermal diffusivity, and Prt, are also presented.

Recent Developments in Calculation Methods for Turbulent Boundary Layers With Pressure Gradients and Heat Transfer

1966 ◽  
Vol 33 (2) ◽  
pp. 429-437 ◽  
Author(s):  
J. C. Rotta
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Temperature Distribution ◽  
Velocity Profile ◽  
Boundary Layers ◽  
Turbulent Boundary Layers ◽  
Pressure Gradients ◽  
Calculation Methods ◽  
Recent Developments ◽  
Incompressible Boundary

A review is given of the recent development in turbulent boundary layers. At first, for the case of incompressible flow, the variation of the shape of velocity profile with the pressure gradient is discussed; also the temperature distribution and heat transfer in incompressible boundary layers are treated. Finally, problems of the turbulent boundary layer in compressible flow are considered.

A Reference Temperature Method for Compressible Laminar Boundary Layers

1973 ◽  
Vol 2 (4) ◽  
pp. 201-204
Author(s):  
R. Camarero
Keyword(s):  
Boundary Layer ◽  
Boundary Layers ◽  
Wall Temperature ◽  
Reference Temperature ◽  
Integral Approach ◽  
Pressure Gradients ◽  
Two Dimensional ◽  
Laminar Boundary Layers ◽  
Temperature Method ◽  
Compressibility Effects

A calculation procedure for the solution of two-dimensional and axi-symmetric laminar boundary layers in compressible flow has been developed. The method is an extension of the integral approach of Tani to include compressibility effects by means of a reference temperature. Arbitrary pressure gradients and wall temperature can be specified. Comparisons with experiments obtained for supersonic flows over a flat plate indicate that the method yields adequate results. The method is then applied to the solution of the boundary layer on a Basemann inlet.

scholarly journals Self-similar compressible turbulent boundary layers with pressure gradients. Part 1. Direct numerical simulation and assessment of Morkovin’s hypothesis

2019 ◽  
Vol 880 ◽  
pp. 239-283 ◽  
Author(s):  
Christoph Wenzel ◽  
Tobias Gibis ◽  
Markus Kloker ◽  
Ulrich Rist
Keyword(s):  
Numerical Simulation ◽  
Boundary Layer ◽  
Mach Number ◽  
Direct Numerical Simulation ◽  
Boundary Layers ◽  
Turbulent Boundary Layers ◽  
Shear Stresses ◽  
Pressure Gradients ◽  
Mean Flow ◽  
Self Similar

A direct numerical simulation study of self-similar compressible flat-plate turbulent boundary layers (TBLs) with pressure gradients (PGs) has been performed for inflow Mach numbers of 0.5 and 2.0. All cases are computed with smooth PGs for both favourable and adverse PG distributions (FPG, APG) and thus are akin to experiments using a reflected-wave set-up. The equilibrium character allows for a systematic comparison between sub- and supersonic cases, enabling the isolation of pure PG effects from Mach-number effects and thus an investigation of the validity of common compressibility transformations for compressible PG TBLs. It turned out that the kinematic Rotta–Clauser parameter $\unicode[STIX]{x1D6FD}_{K}$ calculated using the incompressible form of the boundary-layer displacement thickness as length scale is the appropriate similarity parameter to compare both sub- and supersonic cases. Whereas the subsonic APG cases show trends known from incompressible flow, the interpretation of the supersonic PG cases is intricate. Both sub- and supersonic regions exist in the boundary layer, which counteract in their spatial evolution. The boundary-layer thickness $\unicode[STIX]{x1D6FF}_{99}$ and the skin-friction coefficient $c_{f}$, for instance, are therefore in a comparable range for all compressible APG cases. The evaluation of local non-dimensionalized total and turbulent shear stresses shows an almost identical behaviour for both sub- and supersonic cases characterized by similar $\unicode[STIX]{x1D6FD}_{K}$, which indicates the (approximate) validity of Morkovin’s scaling/hypothesis also for compressible PG TBLs. Likewise, the local non-dimensionalized distributions of the mean-flow pressure and the pressure fluctuations are virtually invariant to the local Mach number for same $\unicode[STIX]{x1D6FD}_{K}$-cases. In the inner layer, the van Driest transformation collapses compressible mean-flow data of the streamwise velocity component well into their nearly incompressible counterparts with the same $\unicode[STIX]{x1D6FD}_{K}$. However, noticeable differences can be observed in the wake region of the velocity profiles, depending on the strength of the PG. For both sub- and supersonic cases the recovery factor was found to be significantly decreased by APGs and increased by FPGs, but also to remain virtually constant in regions of approximated equilibrium.

On Integral Methods for Predicting Shear Layer Behavior

1969 ◽  
Vol 36 (4) ◽  
pp. 673-681 ◽  
Author(s):  
S. J. Shamroth
Keyword(s):  
Boundary Layer ◽  
Shear Layer ◽  
Integral Equations ◽  
Boundary Layers ◽  
Specific Problem ◽  
Shear Layers ◽  
Near Wake ◽  
Integral Methods ◽  
Layer Behavior ◽  
Momentum Integral

The origin and consequences of a nonphysical constraint which may arise when boundary-layer momentum integral equations are used to predict the behavior of shear layers are examined. It is pointed out that should the constraint occur within the domain of integration of the momentum integral equations, the effect may either be catastrophic or significantly constrain the solution. Several methods of solution having the usual advantages associated with boundary-layer momentum integral equations, but free from this constraint, are proposed for the specific problem of the plane turbulent near wake. One method developed to avoid this constraint in the case of a plane turbulent near wake appears to be perfectly general, and therefore, it may be possible to apply this method to both boundary layers and wakes.

Smooth and Rough Turbulent Boundary Layers: A Look at Skin Friction, Pressure Gradient and Roughness

2006 ◽  
Author(s):  
Katherine A. Newhall ◽  
Raul Bayoan Cal ◽  
Brian Brzek ◽  
Gunnar Johansson ◽  
Luciano Castillo
Keyword(s):  
Boundary Layer ◽  
Pressure Gradient ◽  
Skin Friction ◽  
Boundary Layers ◽  
Rough Surfaces ◽  
Boundary Layer Equation ◽  
Roughness Parameter ◽  
Surface Boundary ◽  
Favorable Pressure Gradient ◽  
Momentum Integral

The skin friction for a turbulent boundary layer can be measured and calculated in several ways with varying degrees of accuracy. In particular, the methods of the velocity gradient at the wall, the integrated boundary layer equation and the momentum integral equation are evaluated for both smooth and rough surface boundary layers. These methods are compared to the oil film interferometry technique measurements for the case of smooth surface flows. The integrated boundary layer equation is found to be relatively reliable, and the values computed with this technique are used to investigate the effect of increasing external favorable pressure gradient for both smooth and rough surfaces, and increasing roughness parameter for the rough surfaces.

An Improved k-ε Model for Boundary Layer Flows

1990 ◽  
Vol 112 (1) ◽  
pp. 33-39 ◽  
Author(s):  
Y. Nagano ◽  
M. Tagawa
Keyword(s):  
Boundary Layer ◽  
Plate Boundary ◽  
Adverse Pressure Gradient ◽  
Turbulent Pipe Flow ◽  
Pressure Gradients ◽  
Boundary Layer Flows ◽  
Limiting Behavior ◽  
Diffuser Flow ◽  
Proposed Model ◽  
Made In

An improvement of the k-ε model has been made in conjunction with an accurate prediction of the near-wall limiting behavior of turbulence and the final period of the decay law of free turbulence. The present improved k-ε model has been extended to predict the effects of adverse pressure gradients on shear layers, which most previously proposed models failed to do correctly. The proposed model was tested by application to a turbulent pipe flow, a flat plate boundary layer, a relaminarizing flow, and a diffuser flow with a strong adverse pressure gradient. Agreement with the experiments was generally very satisfactory.

Response of supersonic turbulent boundary layers to local and global mechanical distortions

2009 ◽  
Vol 630 ◽  
pp. 225-265 ◽  
Author(s):  
ISAAC W. EKOTO ◽  
RODNEY D. W. BOWERSOX ◽  
THOMAS BEUTNER ◽  
LARRY GOSS
Keyword(s):  
Boundary Layer ◽  
Turbulent Flow ◽  
Boundary Layers ◽  
Flow Structure ◽  
Small Scale ◽  
Pressure Gradients ◽  
Local Surface ◽  
Turbulence Flow ◽  
Turbulent Flow Structure ◽  
The Mean

The response of the mean and turbulent flow structure of a supersonic high-Reynolds-number turbulent boundary layer flow subjected to local and global mechanical distortions was experimentally examined. Local disturbances were introduced via small-scale wall patterns, and global distortions were induced through streamline curvature-driven pressure gradients. Local surface topologies included k-type diamond and d-type square elements; a smooth wall was examined for comparison purposes. Three global distortions were studied with each of the three surface topologies. Measurements included planar contours of the mean and fluctuating velocity via particle image velocimetry, Pitot pressure profiles, pressure sensitive paint and Schlieren photography. The velocity data were acquired with sufficient resolution to characterize the mean and turbulent flow structure and to examine interactions between the local surface roughness distortions and the imposed pressure gradients on the turbulence production. A strong response to both the local and global distortions was observed with the diamond elements, where the effect of the elements extended into the outer regions of the boundary layer. It was shown that the primary cause for the observed response was the result of local shock and expansion waves modifying the turbulence structure and production. By contrast, the square elements showed a less pronounced response to local flow distortions as the waves were significantly weaker. However, the frictional losses were higher for the blunter square roughness elements. Detailed quantitative characterizations of the turbulence flow structure and the associated production mechanisms are described herein. These experiments demonstrate fundamental differences between supersonic and subsonic rough-wall flows, and the new understanding of the underlying mechanisms provides a scientific basis to systematically modify the mean and turbulence flow structure all the way across supersonic boundary layers.

Sign in / Sign up

Export Citation Format

Share Document