scholarly journals A low-energy chilled ammonia process exploiting controlled solid formation for post-combustion CO2capture

2016 ◽  
Vol 192 ◽  
pp. 59-83 ◽  
Author(s):  
Daniel Sutter ◽  
Matteo Gazzani ◽  
Marco Mazzotti
Keyword(s):  
Solid Phase ◽  
Primary Energy ◽  
Ammonium Bicarbonate ◽  
Operating Conditions ◽  
Wash Water ◽  
Capture Process ◽  
Wide Range ◽  
New Process ◽  
Process Simulations ◽  
Energy Penalty

A new ammonia-based process for CO2capture from flue gas has been developed, which utilizes the formation of solid ammonium bicarbonate to increase the CO2concentration in the regeneration section of the process. Precipitation, separation, and dissolution of the solid phase are realized in a dedicated process section, while the packed absorption and desorption columns remain free of solids. Additionally, the CO2wash section applies solid formation to enable a reduction of the wash water consumption. A rigorous performance assessment employing the SPECCA index (Specific Primary Energy Consumption for CO2Avoided) has been implemented to allow for a comparison of the overall energy penalty between the new process and a standard ammonia-based capture process without solid formation. A thorough understanding of the relevant solid–solid–liquid–vapor phase equilibria and an accurate modeling of them have enabled the synthesis of the process, and have inspired the development of the optimization algorithm used to screen a wide range of operating conditions in equilibrium-based process simulations. Under the assumptions on which the analysis is based, the new process with controlled solid formation achieved a SPECCA of 2.43 MJ kgCO2−1, corresponding to a reduction of 17% compared to the process without solid formation (with a SPECCA of 2.93 MJ kgCO2−1). Ways forward to confirm this significant improvement, and to increase the accuracy of the optimization are also discussed.

3-E Analysis of a Heat Pump Driven by a Micro-Cogenerator

2005 ◽  
Author(s):  
Maurizio Sasso ◽  
Raffaello Possidente ◽  
Carlo Roselli ◽  
Sibilio Sergio
Keyword(s):  
Heat Pump ◽  
Thermal Energy ◽  
Primary Energy ◽  
Operating Conditions ◽  
Environmental Benefits ◽  
Test Facility ◽  
Cooling Mode ◽  
Simplified Approach ◽  
Wide Range ◽  
Network Losses

The cogeneration, or the combined production of electric (and/or mechanical) and thermal energy, is a well established technology, which has important environmental benefits and it has been noted by the European Community as one of the first elements to save primary energy, to avoid network losses and to reduce the greenhouse gas emissions. In particular, the study will be focused on the micro-cogeneration process with micro-combined heat and power system, or MCHP (electric power output ≤ 15 kW), which represents a valid and interesting application of this technology applicable, above all, to residential and light commercial users. This paper presents the Energy, Economic and Environmental (3-E) analysis of a natural gas-fired MCHP in combination with an electric heat pump (EHP). The 3-E analysis of the MCHP/EHP begins with the results of a detailed experimental activity developed in a test facility [1] for a wide range of conditions. Two operating conditions were simulated: a heating mode with co-production of electric and thermal energy, and a cooling mode with co-production of electric, thermal and cooling energy (tri-generation). The annual operating performance, also based on the typical features of the Italian market, is also discussed with a simplified approach.

Numerical Prediction of Pressure Gradient of Slurry Flows in Horizontal Pipes

2013 ◽  
Author(s):  
Gianandrea Vittorio Messa ◽  
Michael Malin ◽  
Stefano Malavasi
Keyword(s):  
Pressure Gradient ◽  
Large Scale ◽  
Solid Phase ◽  
Fluid Model ◽  
Operating Conditions ◽  
Sand Particle ◽  
Horizontal Pipes ◽  
Numerical Predictions ◽  
Wide Range ◽  
Solid Liquid

Pipe flows of solid-liquid mixtures in the form of slurries are frequently encountered in many engineering applications. The pressure gradient is perhaps the most serious concern of designers, as it dictates the selection of pump capacity. Due to their versatility, in the sense of applicability to large scale systems and more complex flows, CFD models have been an attractive tool in recent years. The fully-suspended flow of solid-liquid slurries in horizontal pipes is simulated by means of a two-fluid model. In particular, the effect of the wall boundary condition for the solid phase on the pressure gradient is discussed, considering different alternatives. The numerical predictions were compared to experimental measurements from open literature over a wide range of operating conditions, in terms of pipe diameter (53.2 to 103 mm), grain material (glass beads and sand), particle size (90 to 370 μm), slurry velocity (1.5 to 8 m/s), and mean solids concentration (up to 40%). The equilibrium wall function of Launder and Spalding for smooth walls proved adequate for fully-suspended flows, but overestimates the losses if the particles are large compared to the boundary layer thickness. Guidelines are provided for defining the numerical set-up and evaluating the uncertainty of the numerical results.

Comparison of Deterministic and Linear Cosine Spatial Filtering of Transmission Electron Micrographs

1972 ◽  
Vol 30 ◽  
pp. 596-597
Author(s):  
David A. Ansley
Keyword(s):  
Spherical Aberration ◽  
Focal Length ◽  
Chromatic Aberration ◽  
Spatial Filter ◽  
Operating Conditions ◽  
Objective Lens ◽  
List Type ◽  
Spatial Filters ◽  
Transmission Electron ◽  
Wide Range

The coherence of the electron flux of a transmission electron microscope (TEM) limits the direct application of deconvolution techniques which have been used successfully on unmanned spacecraft programs. The theory assumes noncoherent illumination. Deconvolution of a TEM micrograph will, therefore, in general produce spurious detail rather than improved resolution.A primary goal of our research is to study the performance of several types of linear spatial filters as a function of specimen contrast, phase, and coherence. We have, therefore, developed a one-dimensional analysis and plotting program to simulate a wide 'range of operating conditions of the TEM, including adjustment of the:(1) Specimen amplitude, phase, and separation(2) Illumination wavelength, half-angle, and tilt(3) Objective lens focal length and aperture width(4) Spherical aberration, defocus, and chromatic aberration focus shift(5) Detector gamma, additive, and multiplicative noise constants(6) Type of spatial filter: linear cosine, linear sine, or deterministic

Structure and properties of compact articles from high-alloyed iron powder with adding of boron nitride

2020 ◽  
pp. 39-48
Author(s):  
B. O. Bolshakov ◽  
◽  
R. F. Galiakbarov ◽  
A. M. Smyslov ◽  
◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Boron Nitride ◽  
Grain Boundary ◽  
Bending Strength ◽  
Physical And Mechanical Properties ◽  
Operating Conditions ◽  
Structure And Properties ◽  
Steam Turbines ◽  
Friction Forces ◽  
Wide Range

The results of the research of structure and properties of a composite compact from 13 Cr – 2 Мо and BN powders depending on the concentration of boron nitride are provided. It is shown that adding boron nitride in an amount of more than 2% by weight of the charge mixture leads to the formation of extended grain boundary porosity and finely dispersed BN layers in the structure, which provides a high level of wearing properties of the material. The effect of boron nitride concentration on physical and mechanical properties is determined. It was found that the introduction of a small amount of BN (up to 2 % by weight) into the compacts leads to an increase in plasticity, bending strength, and toughness by reducing the friction forces between the metal powder particles during pressing and a more complete grain boundary diffusion process during sintering. The formation of a regulated structure-phase composition of powder compacts of 13 Cr – 2 Mо – BN when the content of boron nitride changes in them allows us to provide the specified physical and mechanical properties in a wide range. The obtained results of studies of the physical and mechanical characteristics of the developed material allow us to reasonably choose the necessary composition of the powder compact for sealing structures of the flow part of steam turbines, depending on their operating conditions.

Nitrogen Removal from Anaerobically-Treated Leachate

1984 ◽  
Vol 19 (1) ◽  
pp. 87-100
Author(s):  
D. Prasad ◽  
J.G. Henry ◽  
P. Elefsiniotis
Keyword(s):  
Nitrogen Removal ◽  
Air Flow ◽  
Operating Conditions ◽  
Air Flow Rate ◽  
Flow Rates ◽  
Anaerobic Filter ◽  
Ph Values ◽  
Wide Range ◽  
Ammonia Desorption ◽  
Effects Of Ph

Abstract Laboratory studies were conducted to demonstrate the effectiveness of diffused aeration for the removal of ammonia from the effluent of an anaerobic filter treating leachate. The effects of pH, temperature and air flow on the process were studied. The coefficient of desorption of ammonia, KD for the anaerobic filter effluent (TKN 75 mg/L with NH3-N 88%) was determined at pH values of 9, 10 and 11, temperatures of 10, 15, 20, 30 and 35°C, and air flow rates of 50, 120, and 190 cm3/sec/L. Results indicated that nitrogen removal from the effluent of anaerobic filters by ammonia desorption was feasible. Removals exceeding 90% were obtained with 8 hours aeration at pH of 10, a temperature of 20°C, and an air flow rate of 190 cm3/sec/L. Ammonia desorption coefficients, KD, determined at other temperatures and air flow rates can be used to predict ammonia removals under a wide range of operating conditions.

Analysis of Aromatic Amines in Industrial Wastewater by Capillary Gas Chromatography-Mass Spectrometry

2000 ◽  
Vol 35 (2) ◽  
pp. 245-262 ◽  
Author(s):  
Francis I. Onuska ◽  
Ken A. Terry ◽  
R. James Maguire
Keyword(s):  
Gas Chromatography ◽  
Aromatic Amines ◽  
Methylene Chloride ◽  
Solid Phase ◽  
Stationary Phases ◽  
Gas Chromatography Mass Spectrometry ◽  
Substituted Anilines ◽  
Environmental Media ◽  
Solid Phase Extraction Cartridge ◽  
Wide Range

Abstract The analysis of aromatic amines, particularly benzidines, at trace levels in environmental media has been difficult because of the lack of suitable deactivated capillary column stationary phases for gas chromatography. This report describes the use of an improved type of column as well as a method for the analysis of anilines and benzidines in water, wastewater and sewage samples. Extraction procedures are applicable to a wide range of compounds that are effectively partitioned from an aqueous matrix into methylene chloride, or onto a solid-phase extraction cartridge. The extracted analytes are also amenable to separation on a capillary gas chromatographic column and transferable to the mass spectrometer. These contaminants are converted to their N-trifluoroacetyl derivatives. Aniline and some substituted anilines, and 3,3’-dichlorobenzidine and benzidine were determined in 24-h composite industrial water, wastewater, primary sludge and final effluent samples at concentrations from 0.03 up to 2760 µg/L.

Recent Application of Polystyrene-supported Triphenylphosphine in Solid-Phase Organic Synthesis

2019 ◽  
Vol 23 (6) ◽  
pp. 643-678
Author(s):  
Lalthazuala Rokhum ◽  
Ghanashyam Bez
Keyword(s):  
Organic Synthesis ◽  
Combinatorial Chemistry ◽  
Solid Phase ◽  
Recent Application ◽  
Organic Transformations ◽  
Solid Phase Organic Synthesis ◽  
Wide Range ◽  
Fast Development ◽  
Polymer Supported

Recent years have witnessed a fast development of solid phase synthetic pathways, a variety of solid-supported reagent and its applications in diverse synthetic strategies and pharmaceutical applicability’s. Polymer-supported triphenylphosphine is getting a lot of applications owing to the speed and simplicity in the process. Furthermore, ease of recyclability and reuse of polymer-supported triphenylphosphine added its advantages. This review covers a wide range of useful organic transformations which are accomplished using cross-linked polystyrene-supported triphenylphosphine with the aim of giving renewed interest in the field of organic and medicinal-combinatorial chemistry.

scholarly journals Applications of Biocatalysts for Sustainable Oxidation of Phenolic Pollutants: A Review

2021 ◽  
Vol 13 (15) ◽  
pp. 8620
Author(s):  
Sanaz Salehi ◽  
Kourosh Abdollahi ◽  
Reza Panahi ◽  
Nejat Rahmanian ◽  
Mozaffar Shakeri ◽  
...  
Keyword(s):  
Phenolic Compounds ◽  
Operating Conditions ◽  
Phenolic Pollutants ◽  
Petroleum Refinery Wastewater ◽  
Start Up ◽  
Low Concentrations ◽  
Effective Removal ◽  
Wide Range ◽  
Loading Effects ◽  
Spent Caustic

Phenol and its derivatives are hazardous, teratogenic and mutagenic, and have gained significant attention in recent years due to their high toxicity even at low concentrations. Phenolic compounds appear in petroleum refinery wastewater from several sources, such as the neutralized spent caustic waste streams, the tank water drain, the desalter effluent and the production unit. Therefore, effective treatments of such wastewaters are crucial. Conventional techniques used to treat these wastewaters pose several drawbacks, such as incomplete or low efficient removal of phenols. Recently, biocatalysts have attracted much attention for the sustainable and effective removal of toxic chemicals like phenols from wastewaters. The advantages of biocatalytic processes over the conventional treatment methods are their ability to operate over a wide range of operating conditions, low consumption of oxidants, simpler process control, and no delays or shock loading effects associated with the start-up/shutdown of the plant. Among different biocatalysts, oxidoreductases (i.e., tyrosinase, laccase and horseradish peroxidase) are known as green catalysts with massive potentialities to sustainably tackle phenolic contaminants of high concerns. Such enzymes mainly catalyze the o-hydroxylation of a broad spectrum of environmentally related contaminants into their corresponding o-diphenols. This review covers the latest advancement regarding the exploitation of these enzymes for sustainable oxidation of phenolic compounds in wastewater, and suggests a way forward.

scholarly journals Wide range continuously tunable and fast thermal switching based on compressible graphene composite foams

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Tingting Du ◽  
Zixin Xiong ◽  
Luis Delgado ◽  
Weizhi Liao ◽  
Joseph Peoples ◽  
...  
Keyword(s):  
Thermal Management ◽  
Dynamic Control ◽  
Operating Conditions ◽  
Dynamic Thermal Management ◽  
Graphene Composite ◽  
Continuous Tuning ◽  
Composite Foams ◽  
Wide Range ◽  
Thermal Switches ◽  
Thermal Switching

AbstractThermal switches have gained intense interest recently for enabling dynamic thermal management of electronic devices and batteries that need to function at dramatically varied ambient or operating conditions. However, current approaches have limitations such as the lack of continuous tunability, low switching ratio, low speed, and not being scalable. Here, a continuously tunable, wide-range, and fast thermal switching approach is proposed and demonstrated using compressible graphene composite foams. Large (~8x) continuous tuning of the thermal resistance is achieved from the uncompressed to the fully compressed state. Environmental chamber experiments show that our variable thermal resistor can precisely stabilize the operating temperature of a heat generating device while the ambient temperature varies continuously by ~10 °C or the heat generation rate varies by a factor of 2.7. This thermal device is promising for dynamic control of operating temperatures in battery thermal management, space conditioning, vehicle thermal comfort, and thermal energy storage.

scholarly journals Recent Developments in the Determination of Biomarkers of Tobacco Smoke Exposure in Biological Specimens: A Review

2021 ◽  
Vol 18 (4) ◽  
pp. 1768
Author(s):  
Hernâni Marques ◽  
Pedro Cruz-Vicente ◽  
Tiago Rosado ◽  
Mário Barroso ◽  
Luís A. Passarinha ◽  
...  
Keyword(s):  
Tobacco Smoke ◽  
Solid Phase ◽  
Smoke Exposure ◽  
Tobacco Smoke Exposure ◽  
World Health ◽  
Second Hand Smoke ◽  
Tobacco Exposure ◽  
Wide Range ◽  
Recent Developments

Environmental tobacco smoke exposure (ETS) and smoking have been described as the most prevalent factors in the development of certain diseases worldwide. According to the World Health Organization, more than 8 million people die every year due to exposure to tobacco, around 7 million due to direct ETS and the remaining due to exposure to second-hand smoke. Both active and second-hand exposure can be measured and controlled using specific biomarkers of tobacco and its derivatives, allowing the development of more efficient public health policies. Exposure to these compounds can be measured using different methods (involving for instance liquid- or gas-chromatographic procedures) in a wide range of biological specimens to estimate the type and degree of tobacco exposure. In recent years, a lot of research has been carried out using different extraction methods and different analytical equipment; this way, liquid–liquid extraction, solid-phase extraction or even miniaturized procedures have been used, followed by chromatographic analysis coupled mainly to mass spectrometric detection. Through this type of methodologies, second-hand smokers can be distinguished from active smokers, and this is also valid for e-cigarettes and vapers, among others, using their specific biomarkers. This review will focus on recent developments in the determination of tobacco smoke biomarkers, including nicotine and other tobacco alkaloids, specific nitrosamines, polycyclic aromatic hydrocarbons, etc. The methods for their detection will be discussed in detail, as well as the potential use of threshold values to distinguish between types of exposure.

Sign in / Sign up

Export Citation Format

Share Document