scholarly journals Validation study for Large-Eddy Simulation of Forest Flow

2020 ◽  
Vol 207 ◽  
pp. 02010
Author(s):  
George Pitchurov ◽  
Christof Gromke ◽  
Jordan A. Denev ◽  
Flavio Cesar Cunha Galeazzo
Keyword(s):  
Wind Tunnel ◽  
Large Eddy Simulation ◽  
Forest Canopy ◽  
Turbulence Models ◽  
Leading Edge ◽  
Eddy Simulation ◽  
Sink Term ◽  
Large Eddy ◽  
Open Test ◽  
Strong Winds

The publication presents Large-Eddy Simulation (LES) of flow over a reduced-scale wind tunnel model of a forest canopy. The final aim of the study is to determine factors responsible for damage in forests by strong winds. The wind tunnel forest was represented by an open-porous foam material for the crown layer and wooden dowels for the trunk layer. The forest model was installed in the open test section of a Goettingen-type wind tunnel and Particle Image Velocimetry (PIV) measurements were made for the acquisition of the flow field data. The numerical simulations were performed with OpenFOAM®. The forest was modelled by an additional sink term in the momentum transport equations based on the leaf area density and a characteristic drag coefficient for the underlying tree specimen. Large-eddy simulations with different subgrid-scale (SGS) turbulence models were carried out and compared to wind tunnel data. The Smagorinsky SGS model outperformed the dynamic Lagrangian SGS model in the windward edge region (within a distance of approximately 2 tree heights from the leading edge) whereas the dynamic Lagrangian SGS model showed a better performance for regions farther downstream.

scholarly journals Large-Eddy Simulation of a microburst

2011 ◽  
Vol 11 (17) ◽  
pp. 9323-9331 ◽  
Author(s):  
V. Anabor ◽  
U. Rizza ◽  
E. L. Nascimento ◽  
G. A. Degrazia
Keyword(s):  
Large Eddy Simulation ◽  
Three Dimensional ◽  
Leading Edge ◽  
Dimensional Structure ◽  
Ring Vortex ◽  
Surface Winds ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Strong Winds ◽  
Complex Phenomena

Abstract. The three-dimensional structure and evolution of an isolated and stationary microburst are simulated using a time-dependent, high resolution Large-Eddy-Simulation (LES) model. The microburst is initiated by specifying a simplified cooling source at the top of the domain around 2 km a.g.l. that leads to a strong downdraft. Surface winds of the order of 30 m s−1 were obtained over a region of 500 m radius around the central point of the impinging downdraft, with the simulated microburst lasting for a few minutes. These characteristic length and time scales are consistent with results obtained from numerical simulations of microbursts using cloud-resolving models. The simulated flow replicated some of the principal features of microbursts observed by Doppler radars: in particular, the horizontal spread of strong surface winds and a ring vortex at the leading edge of the cold outflow. In addition to the primary surface outflow, the simulation also generated a secondary surge of strong winds that appears to represent a pulsation in the microburst evolution. These results highlight the capability of LES to reproduce complex phenomena like microbursts, indicating the potential usage of LES models to represent atmospheric phenomena of time and space scales between the convective scale and the microscale. These include short-lived convectively-generated damaging winds.

scholarly journals Large Eddy Simulation of Film Cooling Involving Compound Angle Holes: Comparative Study of LES and RANS

Processes ◽  
2021 ◽  
Vol 9 (2) ◽  
pp. 198
Author(s):  
Seung Il Baek ◽  
Joon Ahn
Keyword(s):  
Large Eddy Simulation ◽  
Film Cooling ◽  
Orientation Angle ◽  
Turbulence Models ◽  
Film Cooling Effectiveness ◽  
Injection Angle ◽  
Blowing Ratio ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Compound Angle

A large eddy simulation (LES) was performed for film cooling in the gas turbine blade involving spanwise injection angles (orientation angles). For a streamwise coolant injection angle (inclination angle) of 35°, the effects of the orientation angle were compared considering a simple angle of 0° and 30°. Two ratios of the coolant to main flow mass flux (blowing ratio) of 0.5 and 1.0 were considered and the experimental conditions of Jung and Lee (2000) were adopted for the geometry and flow conditions. Moreover, a Reynolds averaged Navier–Stokes simulation (RANS) was performed to understand the characteristics of the turbulence models compared to those in the LES and experiments. In the RANS, three turbulence models were compared, namely, the realizable k-ε, k-ω shear stress transport, and Reynolds stress models. The temperature field and flow fields predicted through the RANS were similar to those obtained through the experiment and LES. Nevertheless, at a simple angle, the point at which the counter-rotating vortex pair (CRVP) collided on the wall and rose was different from that in the experiment and LES. Under the compound angle, the point at which the CRVP changed to a single vortex was different from that in the LES. The adiabatic film cooling effectiveness could not be accurately determined through the RANS but was well reflected by the LES, even under the compound angle. The reattachment of the injectant at a blowing ratio of 1.0 was better predicted by the RANS at the compound angle than at the simple angle. The temperature fluctuation was predicted to decrease slightly when the injectant was supplied at a compound angle.

Evaluation of Turbulence Models Using Direct Numerical and Large-Eddy Simulation Data

2011 ◽  
Vol 133 (2) ◽  
Author(s):  
Hassan Raiesi ◽  
Ugo Piomelli ◽  
Andrew Pollard
Keyword(s):  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Eddy Viscosity ◽  
Predictive Accuracy ◽  
Turbulence Models ◽  
Special Treatment ◽  
Two Dimensional ◽  
Square Duct ◽  
Eddy Simulation ◽  
Large Eddy

The performance of some commonly used eddy-viscosity turbulence models has been evaluated using direct numerical simulation (DNS) and large-eddy simulation (LES) data. Two configurations have been tested, a two-dimensional boundary layer undergoing pressure-driven separation, and a square duct. The DNS and LES were used to assess the k−ε, ζ−f, k−ω, and Spalart–Allmaras models. For the two-dimensional separated boundary layer, anisotropic effects are not significant and the eddy-viscosity assumption works well. However, the near-wall treatment used in k−ε models was found to have a critical effect on the predictive accuracy of the model (and, in particular, of separation and reattachment points). None of the wall treatments tested resulted in accurate prediction of the flow field. Better results were obtained with models that do not require special treatment in the inner layer (ζ−f, k−ω, and Spalart–Allmaras models). For the square duct calculation, only a nonlinear constitutive relation was found to be able to capture the secondary flow, giving results in agreement with the data. Linear models had significant error.

Large Eddy Simulation of Wake-Shear Layer Interactions Over a Multi-Element Aerofoil

2020 ◽  
Author(s):  
Souvik Naskar ◽  
S. Sarkar
Keyword(s):  
Large Eddy Simulation ◽  
Shear Layer ◽  
Separation Bubble ◽  
Turbine Blades ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Suction Surface ◽  
Free Stream Turbulence ◽  
Eddy Simulation ◽  
Large Eddy

Abstract Modern commercial airliners use multi-element aerofoils to enhance take-off and landing performance. Further, multielement aerofoil configurations have been shown to improve the aerodynamic characteristics of wind turbines. In the present study, high resolution Large Eddy Simulation (LES) is used to explore the low Reynolds Number (Re = 0.832 × 104) aerodynamics of a 30P30N multi-element aerofoil at an angle of attack, α = 4°. In the present simulation, wake shed from a leading edge element or slat is found to interact with the separated shear layer developing over the suction surface of the main wing. High receptivity of shear layer via amplification of free-stream turbulence leads to rollup and breakdown, forming a large separation bubble. A transient growth of fluctuations is observed in the first half of the separation bubble, where levels of turbulence becomes maximum near the reattachment and then decay depicting saturation of turbulence. Results of the present LES are found to be in close agreement with the experiment depicting high vortical activity in the outer layer. Some features of the flow field here are similar to those occur due to interactions of passing wake and the separated boundary layer on the suction surface of high lift low pressure turbine blades.

scholarly journals Investigation of the velocity field downstream of a benchmark vent using numerical simulation and hot-wire anemometry

2019 ◽  
Vol 213 ◽  
pp. 02076
Author(s):  
Jan Sip ◽  
Frantisek Lizal ◽  
Jakub Elcner ◽  
Jan Pokorny ◽  
Miroslav Jicha
Keyword(s):  
Fluid Dynamics ◽  
Numerical Simulation ◽  
Velocity Field ◽  
Flow Field ◽  
Large Eddy Simulation ◽  
Turbulence Models ◽  
Hot Wire ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Precise Prediction

The velocity field in the area behind the automotive vent was measured by hot-wire anenemometry in detail and intensity of turbulence was calculated. Numerical simulation of the same flow field was performed using Computational fluid dynamics in commecial software STAR-CCM+. Several turbulence models were tested and compared with Large Eddy Simulation. The influence of turbulence model on the results of air flow from the vent was investigated. The comparison of simulations and experimental results showed that most precise prediction of flow field was provided by Spalart-Allmaras model. Large eddy simulation did not provide results in quality that would compensate for the increased computing cost.

Large Eddy Simulation on the Interactions of Wake and Film-Cooling Near a Leading Edge

2014 ◽  
Vol 137 (1) ◽  
Author(s):  
S. Sarkar ◽  
Harish Babu
Keyword(s):  
Large Eddy Simulation ◽  
Film Cooling ◽  
Vortex Pair ◽  
Leading Edge ◽  
Horseshoe Vortex ◽  
Constant Thickness ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Flow Past A Cylinder ◽  
Downward Spiral

The unsteady flow physics due to interactions between a separated shear layer and film cooling jet apart from excitation of periodic passing wake are studied using large eddy simulation (LES). An aerofoil of constant thickness with rounded leading edge induced flow separation, while film cooling jets were injected normal to the crossflow a short distance downstream of the blend point. Wake data extracted from precursor LES of flow past a cylinder are used to replicate a moving bar that generates wakes in front of a cascade (in this case, an infinite row of the model aerofoils). This setup is a simplified representation of rotor-stator interaction in a film cooled gas turbine. The results of numerical simulation are presented to elucidate the formation, convection and breakdown of flow structures associated with the highly anisotropic flow involved in film cooling perturbed by convective wakes. The various vortical structures namely, horseshoe vortex, roller vortex, upright wake vortex, counter rotating vortex pair (CRVP), and downward spiral separation node (DSSN) vortex associated with film cooling are resolved. The effects of wake on the evolution of these structures are then discussed.

A Dynamic Time Filtering Technique for Hybrid RANS-LES Simulation of Non-Stationary Turbulent Flow

2019 ◽  
Author(s):  
Tausif Jamal ◽  
D. Keith Walters
Keyword(s):  
Large Eddy Simulation ◽  
Comprehensive Evaluation ◽  
Model Performance ◽  
Turbulence Models ◽  
Mean Flow ◽  
Complex Flow ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Filtering Technique ◽  
Dynamic Time

Abstract Unsteady turbulent wall bounded flows can produce complex flow physics including temporally varying mean pressure gradients, intermittent regions of high turbulence intensity, and interaction of different scales of motion. As a representative example, pulsating channel flow presents significant challenges for newly developed and existing turbulence models in computational fluid dynamics (CFD) simulations. The present study investigates the performance of the Dynamic Hybrid RANS-LES (DHRL) model with a newly proposed dynamic time filtering (DTF) technique, compared against an industry standard Reynolds-Averaged Navier-Stokes (RANS) model, Monotonically Integrated Large Eddy Simulation (MILES), and two conventional Hybrid RANS-LES (HRL) models. Model performance is evaluated based on comparison to previously documented Large Eddy Simulation (LES) results. Simulations are performed for a fully developed flow in a channel with time-periodic driving pressure gradient. Results highlight the relative merits of each model type and indicate that the use of a dynamic time filtering technique improves the accuracy of the DHRL model when compared to a static time filtering technique. A comprehensive evaluation of the results suggests that the DHRL-DTF method provides the most consistently accurate reproduction of the time-dependent mean flow characteristics for all models investigated.

A Large Eddy Simulation of the Bubbly Flow in Vertical Tube

2012 ◽  
Author(s):  
Peng Zhang ◽  
Xu Hong
Keyword(s):  
Large Eddy Simulation ◽  
Eddy Viscosity ◽  
Bubbly Flow ◽  
Turbulence Models ◽  
Vertical Tube ◽  
Simulation Approach ◽  
Bubble Distribution ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Two Fluid

This paper simulates the dispersed bubbly flow in a vertical tube with two different turbulence models based on Eulerian two-fluid frameworks. Both the RANS (Reynolds Averaged N-S equation) approach and LES (Large Eddy Simulation) approach can get results agreed with experiment well. The “wall peak” bubble distribution is captured. Compare with RANS with SST (Shear Stress Transport) turbulence model, the LES with WALE (Wall-Adapted Local Eddy-viscosity) sub-grid model can give transient and detail information of the flow field, and it shows better agreement.

Sign in / Sign up

Export Citation Format

Share Document