scholarly journals Factory Tea Waste Biosorbent for Cu(II) and Zn(II) Removal from Wastewater

2021 ◽  
Vol 287 ◽  
pp. 04006
Author(s):  
Patrick Tan Peng Jun ◽  
Wan Nur Aisyah Wan Osman ◽  
Shafirah Samsuri ◽  
Juniza Md Saad ◽  
Muhamad Fadli Samsudin ◽  
...  
Keyword(s):  
Heavy Metal ◽  
Removal Efficiency ◽  
Metal Ion ◽  
Metal Removal ◽  
Ph Value ◽  
Heavy Metal Removal ◽  
Fixed Bed ◽  
Ion Concentration ◽  
Fixed Bed Adsorption ◽  
Tea Waste

Recent studies have shown great interest toward heavy metal removal due to its hazardous and non-biodegradable properties. Many approaches have been used for this purpose and one of them is adsorption. In this study, several experiments were carried out to investigate the feasibility of factory tea waste as a biosorbent in a fixed-bed adsorption column for heavy metal removal (zinc and copper) in wastewater. The results highlighted that zinc has better performance compared to copper in terms of the effect of initial ion concentration, pH value, and the mixed ions with respect to the removal efficiency. Zinc showed higher removal efficiency and adsorption capacity at the initial metal ion concentration of 200 mg/L, which are 99.21% and 39.68 mg/mg compared to copper. Meanwhile, for the effect of pH values and mixed ion concentration, zinc also showed slightly higher removal efficiency which are 99.91% and 98.47%, respectively compared to copper. However, both zinc and copper showed a better fit to the Langmuir isotherm. The factory tea waste was characterized using Micromeritics ASAP 2020 instrument and results showed that the factory tea waste biosorbent consists of mesopores with the diameter and width of 4.85205 and 2.546985 nm, respectively.

scholarly journals Heavy Metal Ion Adsorption Properties of Methacrylamidocysteine-Containing Porous Poly(Hydroxyethyl Methacrylate) Chelating Beads

2002 ◽  
Vol 20 (7) ◽  
pp. 607-617 ◽  
Author(s):  
Adil Denizli ◽  
Bora Garipcan ◽  
Sibel Emir ◽  
Süleyman Patir ◽  
Ridvan Say
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Metal Ion ◽  
Heavy Metal Ions ◽  
Metal Removal ◽  
Ph Value ◽  
Heavy Metal Removal ◽  
Ion Concentration ◽  
Heavy Metal Ion ◽  
Adsorption Capacities

Details of the adsorption performance of poly(2-hydroxyethylmethacrylate–methacrylamidocysteine) [p(HEMA–MAC)] beads towards the removal of heavy metal ions from aqueous solution were studied. The metal-complexing ligand and/or co-monomer MAC was newly synthesized from methylacrylochloride and cysteine. Spherical beads of average size 150–200 mm were obtained by the radical suspension polymerization of MAC and HEMA conducted in an aqueous dispersion. The p(HEMA–MAC) beads obtained had a specific surface area of 18.9 m2/g. p(HEMA–MAC) beads were characterized by swelling studies, FT-IR spectroscopy and elemental analysis. Such beads with a swelling ratio of 72%, and containing 3.9 mmol MAC/g, were used for heavy metal removal studies. The adsorption capacities of the beads for selected metal ions, i.e. CdII, AsIII, CrIII, HgII and PbII, were investigated in aqueous media containing different amounts of these ions (10–750 mg/l) and at different pH values (3.0–7.0). The adsorption rate was fast in all cases. The maximum adsorption capacities of the p(HEMA–MAC) beads were 1058.2 mg/g for CdII, 123.4 mg/g for AsIII, 199.6 mg/g for CrIII, 639.1 mg/g for PbII and 1018.6 mg/g for HgII. On a molar basis, the following affinity order was observed: CdII > HgII > CrIII > PbII >AsIII. The adsorption capacity of the MAC-incorporated beads was affected significantly by the pH value of the aqueous medium. The adsorption of heavy metal ions from artificial wastewater was also studied. In this case, the adsorption capacities were 52.2 mg/g for CdII, 23.1 mg/g for CrIII, 83.4 mg/g for HgII, 62.6 mg/g for PbII and 11.1 mg/g for AsIII at an initial metal ion concentration of 0.5 mmol/l. The chelating beads could be regenerated easily with a higher effectiveness by 0.1 M HNO3. These features make p(HEMA–MAC) beads potential candidates for heavy metal ion removal at high capacity.

scholarly journals Removal of chromium and Iron using mixed adsorbent for synthetic and industrial samples in a continuous column reactor

YMER Digital ◽  
2022 ◽  
Vol 21 (01) ◽  
pp. 98-111
Author(s):  
Dr. Srinivas Tadepalli ◽  
◽  
Dr. K.S.R Murthy ◽  
Dr. P Suresh Kumar ◽  
Dr. Prasanthi Kumari Nunna ◽  
...  
Keyword(s):  
Metal Ion ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Fixed Bed ◽  
Industrial Effluent ◽  
Ion Concentration ◽  
Flow Rates ◽  
Saturation Time ◽  
Bed Height ◽  
Synthetic Solution

he results of the experiments showed that bed weight, flow rate, and initial metal ion concentration all play a role in the removal of Cr (III) and Fe (II). The optimized break through curve was obtained at 36cm bed height and 10ml/min for chromium where 97.5 to 100% removal was observed at a saturation time of 500-600 min. With the increase in bed height from 12cm to 36cm, both the breakthrough and saturation times for Cr (III) increased. The break through time at 12cm, 24cm, 36cm and 10ml/min for Cr (III) were 70 min, 105 min, and 35 min respectively. The saturation time for Cr (III) at 12cm, 24cm, 36cm and 10ml/min were 460 min, 490 min, and 500 min respectively. Similarly, the break through time for Fe (II) at 12cm, 24cm, 36cm and 10ml/min were 70 min, 80 min, and 100 min respectively. At 12cm, 24cm, 36cm, and 10ml/min, the saturation time for Fe (III) was 340 minutes, 360 minutes, and 430 minutes, respectively. Overall in the column performance comparison between synthetic solution and industrial effluents for chromium, synthetic solution performance was more superior at fixed volumetric flow rates of 10 ml/min and bed heights ranging from 12 cm to 36 cm But the reverse trend was observed in case of fixed bed heights of 36 cm (150 g) and variation of volumetric flow rates from 10ml/min to 30ml/min which indicates that industrial effluent performance was superior when compared to synthetic solution for heavy metal removal.

scholarly journals The kinetics of Fe2+ heavy metal adsorption by microalgae Desmodesmus sp. beads

2021 ◽  
Vol 894 (1) ◽  
pp. 012040
Author(s):  
D A Widyaningrum ◽  
A Rinanti ◽  
R Hadisoebroto
Keyword(s):  
Heavy Metal ◽  
Removal Efficiency ◽  
Adsorption Kinetics ◽  
Metal Ion ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Growth Media ◽  
Green Microalgae ◽  
Alginate Concentration ◽  
Ph Level

Abstract Industrial waste that contains high concentration of iron heavy metal (Fe2+) needs to be reduced into a safer limit for water ecosystem using an environmental-friendly, sustainable and low cost technology. This literature study was aimed to gather information on Fe2+ metal ion removal with biosorption method by mobilized beads-shaped Desmodesmus sp. green microalgae. Biosorbent beads are made of Desmodesmus sp. green microalgae powder binded with Na-alginate polymer. Desmodesmus sp. microalgae were cultivated in an Erlenmeyer flask with wastewater contains Fe2+ and Beijerinck growth media controlled in batch system. Analysis was conducted to study the influence of pH, size, beads, beads concentration, and Na-alginate concentration towards Fe2+ heavy metal removal efficiency on biosorption process. Research results revealed that Fe2+ heavy metal was effectively adsorbed by 1 mm beads up until 46% at maximum capacity on pH level of 6. These beads contain 8% gr/L of microalgae powder and 9% gr/L of Na-alginate. The involved function groups in Fe2+ sorption and the beads biosorbent morphology changes were analyzed by using FTIR and SEM. This biosorption research was following by analysis of Freundlich isotherm and reaction kinetics order two with linear approach. This was to shows the beads possess adsorption kinetics with optimum Fe2+ absorption capacity. Desmodesmus sp. beads are highly potential to be used as biosorbent since the heavy metal removal process was selectively conducted on wide pH level and temperature ranges, fast adsorption kinetics, and low operational cost. The smaller the beads size the wider the surface area, which leads to higher removal efficiency rate.

scholarly journals Self-Supported Reduced Graphene Oxide Membrane and Its Cu2+ Adsorption Capability

Materials ◽  
2020 ◽  
Vol 14 (1) ◽  
pp. 146
Author(s):  
Yangjinghua Yu ◽  
Zhong Wang ◽  
Runjun Sun ◽  
Zhihua Chen ◽  
Meicheng Liu ◽  
...  
Keyword(s):  
Heavy Metal ◽  
Graphene Oxide ◽  
Reduced Graphene Oxide ◽  
Metal Ion ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Ion Concentration ◽  
Order Kinetic ◽  
Supported Membrane ◽  
Reduced Graphene

Graphene stratiform membrane materials have been recently applied to heavy metal removal in aqueous systems via adsorption due to their high mechanical strength, chemical stability, and other properties. We applied reduced graphene oxide (rGO) alone as an adsorbent to remove heavy metal ions from wastewater. Self-supported rGO membrane was prepared using a green reduction method with sodium hydrosulfite. We used the Raman spectra to observe the structure of the rGO membrane. The morphology of the self-supported membrane was measured by a scanning electron microscope. The Cu2+ adsorption performance was measured in terms of pH, reaction time, metal ion concentration, and temperature. The maximum Cu2+ adsorption capacity of the rGO membrane was found to be 149.25 mg/g. The adsorption process followed a pseudo-second-order kinetic model, and adsorption isotherms were simulated by the Freundlich model.

Electrokinetic Remediation of Heavy Metal Contaminated Soil Using Permeable Reactive Composite Electrodes

2012 ◽  
Vol 518-523 ◽  
pp. 361-368 ◽  
Author(s):  
Rong Bing Fu ◽  
Xin Xing Liu ◽  
Fang Liu ◽  
Jin Ma ◽  
Yu Mei Ma ◽  
...  
Keyword(s):  
Heavy Metal ◽  
Metal Ions ◽  
Removal Efficiency ◽  
Heavy Metal Ions ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Ph Control ◽  
Electrokinetic Remediation ◽  
Composite Electrodes ◽  
Remediation Process

A new permeable reactive composite electrode (PRCE) attached with a permeable reactive layer (PRL) of Fe0 and zeolite has been developed for soil pH control and the improved removal efficiency of heavy metal ions (Cd, Ni, Pb, Cu) from soil in electrokinetic remediation process. The effects of different composite electrodes on pH control and heavy metal removal efficiency were studied, and changes in the forms of heavy metals moved onto the electrodes were analyzed. The results showed that with acidic/alkaline zeolite added and renewed in time, the composite electrodes could effectively neutralize and capture H+ and OH- produced from electrolysis of the anolyte and catholyte, avoiding or delaying the formation of acidic/alkaline front in tested soil, preventing premature precipitation of heavy metal ions and over-acidification of soil, and thus significantly improved the heavy metal removal efficiency. Fe0 in composite electrodes could deoxidize and stabilize the heavy metal ions. After that capture and immobilization of the pollutants were achieved. The results also showed that, using "Fe0 + zeolite" PRCE in the cathode with timely renewal, after 15-day remediation with a DC voltage of 1.5 V/cm, the total removal rates of Cd, Pb, Cu and Ni were 49.4%, 47.1%, 36.7% and 39.2%, respectively.

Pillararenes as macrocyclic hosts: a rising star in metal ion separation

2019 ◽  
Vol 55 (55) ◽  
pp. 7883-7898 ◽  
Author(s):  
Lixi Chen ◽  
Yimin Cai ◽  
Wen Feng ◽  
Lihua Yuan
Keyword(s):  
Heavy Metal ◽  
Metal Ion ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Supramolecular Materials ◽  
Feature Article ◽  
Ion Separation

This feature article reviews the development of functionalized pillararenes as supramolecular materials for lanthanide and actinide separation and heavy metal removal.

scholarly journals Growth and metal removal efficiency of the green algae Schroederia setigera and Selenastrum bibraianum exposed to nickel, zinc and cadmium

2020 ◽  
Vol 58 (5A) ◽  
pp. 22
Author(s):  
Dao Thanh Son ◽  
Van Tai Nguyen ◽  
Thuy Nhu Quynh Vo ◽  
Vinh Quang Tran ◽  
Thi My Chi Vo ◽  
...  
Keyword(s):  
Heavy Metal ◽  
Green Algae ◽  
Removal Efficiency ◽  
Heavy Metal Contamination ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Pilot Scale ◽  
Nickel Zinc ◽  
Ecological Protection

Heavy metal contamination is among the globally environmental and ecological concerns. In this study we assessed the development of the two green algae Schroederia setigera and Selenastrum bibraianum under exposures to 5 – 200 µg/L of Ni, Zn, and Cd in the laboratory conditions. Heavy metal removal efficiency of S. setigera was also tested in 537 µg Ni/L, 734 µg Zn/L, and 858 µg Cd/L. We found that the exposures with these heavy metals caused inhibitory on the growth of S. bibraianum. The S. bibraianum cell size in the 200 µg Zn/L treatment was around two times smaller than the control. However, Zn and Cd at the concentration of 200 µg/L did not inhibit the growth of S. setigera over 18 days of exposure. The S. setigera also grew well during 8 days exposed to Ni at the same concentration. Besides, the alga S. setigera could remove 66% of Zn, 18% of Cd and 12% of Ni out of the test medium after 16 days of incubation. The Vietnam Technical Regulation related to metals should be considered for ecological protection. We recommend to test the metal removal by the alga S. setigera at pilot scale prior to apply it in situ

Removal of Some Heavy Metals by Electrocoagulation

2012 ◽  
Vol 468-471 ◽  
pp. 2882-2890 ◽  
Author(s):  
R. H. Al Anbari ◽  
S. M. Alfatlawi ◽  
J. H. Albaidhani
Keyword(s):  
Heavy Metals ◽  
Heavy Metal ◽  
Removal Efficiency ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Efficient Treatment ◽  
Electrolytic Cells ◽  
Removal Capacity ◽  
Metals Removal ◽  
Working Parameters

Heavy metal removal by electrocoagulation using iron electrodes material was investigated in this paper. Several working parameters, such as pH, current density and heavy metal ions concentration were studied in an attempt to achieve a higher removal capacity. A simple and efficient treatment process for removal of heavy metals is essentially necessary. The performance of continuous flow electrocoagulation system, with reactor consists of a ladder series of twelve electrolytic cells, each cell containing stainless steel cathode and iron anode. The treatment of synthetic solutions containing Zn 2+,Cu 2+,Ni 2+,Cr 3+,Cd 2+ and Co 2+ ,has been investigated. Results showed that iron is very effective as sacrificial electrode material for heavy metals removal efficiency and cost points. Also it was concluded that the chromium has lower efficient removal as compared to zinc, copper and nickel. At the same time cadmium and cobalt have minimum removal efficiency.

Efficient heavy metal ion removal by triazinyl-β-cyclodextrin functionalized iron nanoparticles

RSC Advances ◽  
2015 ◽  
Vol 5 (110) ◽  
pp. 90602-90608 ◽  
Author(s):  
Amir Abdolmaleki ◽  
Shadpour Mallakpour ◽  
Sedigheh Borandeh
Keyword(s):  
Heavy Metal ◽  
Aqueous Solutions ◽  
Metal Ion ◽  
Iron Nanoparticles ◽  
Metal Removal ◽  
Heavy Metal Removal ◽  
Metal Ion Removal ◽  
Ion Removal ◽  
Heavy Metal Ion Removal ◽  
Nano Adsorbent

A novel magnetic nano-adsorbent containing Fe3O4 nanoparticles functionalized with MCT-β-CD was fabricated and exhibited a remarkable enhancement in heavy metal removal efficiency from aqueous solutions.

Sign in / Sign up

Export Citation Format

Share Document