Experimental investigation, modelling and optimization in hard turning of high strength low alloy steel (AISI 4340)

2018 ◽  
Vol 106 (4) ◽  
pp. 404 ◽  
Author(s):  
Asutosh Panda ◽  
Sudhansu Ranjan Das ◽  
Debabrata Dhupal
Keyword(s):  
Surface Roughness ◽  
Tool Life ◽  
Hard Turning ◽  
Research Work ◽  
Cutting Speed ◽  
High Strength ◽  
Depth Of Cut ◽  
Turning Process ◽  
Ceramic Tools ◽  
Aisi 4340

The present study addresses the machinability investigation of high strength low alloy grade AISI 4340 steel with coated ceramic tools on surface roughness, tool wear, and economic analysis by considering the hard turning process parameters such as cutting speed, feed and depth of cut. Twenty seven set of trials according to full factorial design of experiments are conducted. Analysis of variance, multiple regression method, Taguchi method, desirability function approach and Gilbert’s technique are employed for parametric influence study, predictive modelling, response optimization, tool life estimation followed by cost analysis. Results indicated that feed and cutting speed are the most significant and crucial factors for hard turning operation in order to achieve minimum surface roughness of machined component as well as flank wear of cutting tool. Abrasions, adhesion followed by plastic deformation are the key wear mechanisms of coated ceramic insert, resulted 47 min of tool life under optimum cutting conditions and ensued lower total machining cost per part ($ 0.29 only) due to higher tool life, and reduced downtime that justifies cost effectiveness of hard turning. Novelty aspects, the current research work demonstrates the substitution of conventional, expensive and slow cylindrical grinding process, and proposes the most expensive CBN tool alternative using coated ceramic tools in hard turning process from techno-economical and ecological point of views in line with the industrial requirements.

Machinability Investigation of HSLA Steel in Hard Turning with Coated Ceramic Tool: Assessment, Modeling, Optimization and Economic Aspects

2019 ◽  
Vol 18 (04) ◽  
pp. 625-655 ◽  
Author(s):  
Asutosh Panda ◽  
Sudhansu Ranjan Das ◽  
Debabrata Dhupal
Keyword(s):  
Surface Roughness ◽  
Tool Life ◽  
Hard Turning ◽  
Flank Wear ◽  
Desirability Function ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Ceramic Tool ◽  
Life Estimation

The present study addresses the machinability investigation in finish dry hard turning of high strength low alloy steel with coated ceramic tool by considering cutting speed, feed and depth of cut as machining parameters. The technological parameters like surface roughness, flank wear, chip morphology and economical feasibility have been considered to investigate the machinability performances. Twenty seven set of trials according to full factorial design of experiments are performed and analysis of variance, multiple regression method, Taguchi method, desirability function approach and finally Gilbert’s approach are subsequently applied for parametric influence study, mathematical modeling, multi-response optimization, tool life estimation and economic analysis. Results indicated that feed and cutting speed are the most significant controlled as well as dominant factors for hard turning operation if the minimization of the machined surface roughness and tool flank wear is considered. Abrasions, adhesion followed by plastic deformation have been observed to be the principal wear mechanism for tool life estimation and observed tool life for coated ceramic insert is 47[Formula: see text]min under optimum cutting conditions. The total machining cost per part is ensued to be lower ($0.29 only) as a consequence of higher tool life, reduction in downtime and enhancement in savings, which finds economical benefits in hard turning. The current work demonstrates the substitution of conventional, expensive and slow cylindrical grinding process, and proposes the most expensive CBN tool alternative using coated ceramic tools in hard turning process considering techno-economical and ecological aspects.

scholarly journals Comparative assessment of hard turning under dry and minimum quantity lubrication

2021 ◽  
Vol 1206 (1) ◽  
pp. 012007
Author(s):  
Avez Shaikh ◽  
Ajinkya Shinde ◽  
Satish Chinchanikar ◽  
Guruprasad Zagade ◽  
Sonia Pardeshi
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Tool Life ◽  
Hard Turning ◽  
Cutting Speed ◽  
Comparative Assessment ◽  
Depth Of Cut ◽  
Machining Performance ◽  
Dry Cutting ◽  
Optimal Surface

Abstract Hard turning with CBN and ceramic inserts is commonly regarded as a cost-effective alternative to grinding. However, there have been few studies comparing hard turning with low-cost carbide tools to high-cost CBN and ceramic cutting tools. However, when it comes to the usage of cutting coolant during severe turning, there are mixed outcomes. In this study, a PVD-coated TiSiN-TiAlN carbide tool was used to hard turn AISI 52100 steel in a dry and MQL environment. Through multi-objective optimization, a comparative assessment in terms of surface roughness, cutting force, and tool life under various cutting settings is provided. In terms of three components of cutting force, surface roughness, and tool life, mathematical models were constructed to forecast and improve machining performance. Under both dry and MQL conditions, the study discovered an optimal cutting speed of 108 m/min, a feed value of 0.09 mm/rev, and a depth of cut of 0.16 mm. Under MQL, hard turning produced optimal surface roughness and tool life of 0.88 m and 64 minutes, respectively. In comparison to hard turning under dry cutting, the optimal surface roughness was 1.07 m and the tool life was 49 minutes. Under MQL, tool life increased by over 31%, according to the findings of the experiments. Under dry and MQL conditions, however, no significant differences in cutting forces and surface roughness were identified.

Effects of Process Parameters on Surface Roughness and MRR in the hard turning of EN 36 steel

2018 ◽  
pp. 102-110
Author(s):  
Amritpal Singh ◽  
Rakesh Kumar
Keyword(s):  
Surface Roughness ◽  
Material Removal Rate ◽  
Material Removal ◽  
Hard Turning ◽  
Control Parameter ◽  
Removal Rate ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Cutting Condition ◽  
Dry Cutting

In the present study, Experimental investigation of the effects of various cutting parameters on the response parameters in the hard turning of EN36 steel under the dry cutting condition is done. The input control parameters selected for the present work was the cutting speed, feed and depth of cut. The objective of the present work is to minimize the surface roughness to obtain better surface finish and maximization of material removal rate for better productivity. The design of experiments was done with the help of Taguchi L9 orthogonal array. Analysis of variance (ANOVA) was used to find out the significance of the input parameters on the response parameters. Percentage contribution for each control parameter was calculated using ANOVA with 95 % confidence value. From results, it was observed that feed is the most significant factor for surface roughness and the depth of cut is the most significant control parameter for Material removal rate.

OPTIMISING CUTTING PARAMETERS FOR HOT TURNING ON EN31 MATERIAL

2021 ◽  
Vol 5 (10) ◽  
Author(s):  
Prof. Hemant k. Baitule ◽  
Satish Rahangdale ◽  
Vaibhav Kamane ◽  
Saurabh Yende
Keyword(s):  
Surface Roughness ◽  
Surface Finish ◽  
Cutting Speed ◽  
Cutting Parameters ◽  
Machining Process ◽  
Depth Of Cut ◽  
Multiple Time ◽  
Turning Process ◽  
Workpiece Material ◽  
Hot Turning

In any type of machining process the surface roughness plays an important role. In these the product is judge on the basis of their (surface roughness) surface finish. In machining process there are four main cutting parameter i.e. cutting speed, feed rate, depth of cut, spindle speed. For obtaining good surface finish, we can use the hot turning process. In hot turning process we heat the workpiece material and perform turning process multiple time and obtain the reading. The taguchi method is design to perform an experiment and L18 experiment were performed. The result is analyzed by using the analysis of variance (ANOVA) method. The result Obtain by this method may be useful for many other researchers.

Development of Tooling Cost Model for High Speed Hard Turning

2011 ◽  
Vol 418-420 ◽  
pp. 1482-1485 ◽  
Author(s):  
Erry Yulian Triblas Adesta ◽  
Muataz Al Hazza ◽  
Delvis Agusman ◽  
Agus Geter Edy Sutjipto
Keyword(s):  
Feed Rate ◽  
High Speed ◽  
Hard Turning ◽  
Cost Model ◽  
Cutting Tools ◽  
Cutting Speed ◽  
Rake Angle ◽  
Depth Of Cut ◽  
Predictive Regression ◽  
Aisi 4340

The current work presents the development of cost model for tooling during high speed hard turning of AISI 4340 hardened steel using regression analysis. A set of experimental data using ceramic cutting tools, composed approximately of Al2O3 (70%) and TiC (30%) on AISI 4340 heat treated to a hardness of 60 HRC was obtained in the following design boundary: cutting speeds (175-325 m/min), feed rate (0.075-0.125 m/rev), negative rake angle (0 to -12) and depth of cut of (0.1-0.15) mm. The output data is used to develop a new model in predicting the tooling cost using in terms of cutting speed, feed rate, depth of cut and rake angle. Box Behnken Design was used in developing the model. Predictive regression model was found to be capable of good predictions the tooling cost within the boundary design.

scholarly journals Investigations on Surface Roughness and Tool Wear Characteristics in Micro-Turning of Ti-6Al-4V Alloy

Materials ◽  
2020 ◽  
Vol 13 (13) ◽  
pp. 2998 ◽  
Author(s):  
Kubilay Aslantas ◽  
Mohd Danish ◽  
Ahmet Hasçelik ◽  
Mozammel Mia ◽  
Munish Gupta ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Feed Rate ◽  
Removal Rate ◽  
Cutting Speed ◽  
Small Diameter ◽  
Cutting Parameters ◽  
Ti6al4v Alloy ◽  
Depth Of Cut ◽  
Turning Process ◽  
Micro Turning

Micro-turning is a micro-mechanical cutting method used to produce small diameter cylindrical parts. Since the diameter of the part is usually small, it may be a little difficult to improve the surface quality by a second operation, such as grinding. Therefore, it is important to obtain the good surface finish in micro turning process using the ideal cutting parameters. Here, the multi-objective optimization of micro-turning process parameters such as cutting speed, feed rate and depth of cut were performed by response surface method (RSM). Two important machining indices, such as surface roughness and material removal rate, were simultaneously optimized in the micro-turning of a Ti6Al4V alloy. Further, the scanning electron microscope (SEM) analysis was done on the cutting tools. The overall results depict that the feed rate is the prominent factor that significantly affects the responses in micro-turning operation. Moreover, the SEM results confirmed that abrasion and crater wear mechanism were observed during the micro-turning of a Ti6Al4V alloy.

Effect of machining parameters on the surface finish of a metal matrix composite under dry cutting conditions

2015 ◽  
Vol 231 (6) ◽  
pp. 913-923 ◽  
Author(s):  
Brian Boswell ◽  
Mohammad Nazrul Islam ◽  
Ian J Davies ◽  
Alokesh Pramanik
Keyword(s):  
Surface Roughness ◽  
Metal Matrix Composite ◽  
Tool Life ◽  
Surface Finish ◽  
Feed Rate ◽  
Metal Matrix ◽  
Cutting Speed ◽  
Depth Of Cut ◽  
Machining Parameters ◽  
Dry Cutting

The machining of aerospace materials, such as metal matrix composites, introduces an additional challenge compared with traditional machining operations because of the presence of a reinforcement phase (e.g. ceramic particles or whiskers). This reinforcement phase decreases the thermal conductivity of the workpiece, thus, increasing the tool interface temperature and, consequently, reducing the tool life. Determining the optimum machining parameters is vital to maximising tool life and producing parts with the desired quality. By measuring the surface finish, the authors investigated the influence that the three major cutting parameters (cutting speed (50–150 m/min), feed rate (0.10–0.30 mm/rev) and depth of cut (1.0–2.0 mm)) have on tool life. End milling of a boron carbide particle-reinforced aluminium alloy was conducted under dry cutting conditions. The main result showed that contrary to the expectations for traditional machined alloys, the surface finish of the metal matrix composite examined in this work generally improved with increasing feed rate. The resulting surface roughness (arithmetic average) varied between 1.15 and 5.64 μm, with the minimum surface roughness achieved with the machining conditions of a cutting speed of 100 m/min, feed rate of 0.30 mm/rev and depth of cut of 1.0 mm. Another important result was the presence of surface microcracks in all specimens examined by electron microscopy irrespective of the machining condition or surface roughness.

Technological Investigation of Effect of Machining Parameter on Tool Life

2020 ◽  
Vol 22 (4) ◽  
pp. 41-53
Author(s):  
Manojkumar Sheladiya ◽  
◽  
Shailee Acharya ◽  
Ghanshyam Acharya ◽  
◽  
...  
Keyword(s):  
Surface Roughness ◽  
Mild Steel ◽  
Tool Life ◽  
Flank Wear ◽  
Cutting Speed ◽  
Numerical Control ◽  
Cutting Fluid ◽  
Depth Of Cut ◽  
Machining Time ◽  
Machining Parameter

Introduction. The machinability is typical criteria to be investigated and different authors suggested different parameters describing its quantification. Different parameters i. e. speed, feed, depth of cut, tool work-piece combination, machine types and its condition, cutting fluid, machinist expertise, etc. are contributing directly to the tool life. The selection of the tool for the machining impacts greatly on the economic viability of the machining in terms of energy usage and tooling costs. The method of investigation. The current research emphasis mainly on tool life investigation when machining the mild steel specimens ISRO 50, BIS 1732:1989 at constant cutting speed i.e. 200 m / min. In the industries the mild steel material is commonly used for various products manufacturing. Considering the high demands on productivity and surface finish, machining at 200 m / min is the preferred. The computerized numerical control machine (CNC DX-150) is used for the turning. The four corner insert (TNMG 120408) is used for different machining times i.e. 10, 15, 20 and 25 minutes respectively. The flank wear of the tool is measured with calibrated optical microscope. The temperature of the tool corner during machining is continuously measured for possible impact of temperature on bonding properties of the tool insert and impact on red hardness. Results and discussion. The plot of flank wear vs. machining time will give the value of tool life. The other quality output parameter, such as surface roughness, is measured after machining, indicating surface irregularities in root means square value. Efforts have been made to identify the relationship of tool life, machining time, the quantity of metal removed, surface roughness, and tool bit temperature.

In-Process Monitoring and Prediction of Surface Roughness in CNC Turning Process

2011 ◽  
Vol 199-200 ◽  
pp. 1958-1966 ◽  
Author(s):  
Somkiat Tangjitsitcharoen
Keyword(s):  
Surface Roughness ◽  
Cutting Force ◽  
Prediction Accuracy ◽  
Cutting Speed ◽  
Least Square ◽  
Depth Of Cut ◽  
Turning Process ◽  
Roughness Model ◽  
Force Ratio ◽  
Cnc Turning Process

The objective of this research is to propose a practical model to predict the in-process surface roughness during the turning process by using the cutting force ratio. The proposed in-process surface roughness model is developed based on the experimentally obtain result by employing the exponential function with six factors of the cutting speed, the feed rate, the rank angle the tool nose radius, the depth of cut, and the cutting force ratio. The multiple regression analysis is utilized to calculate the regression coefficients with the use of the least square method. The prediction accuracy of the in-process surface roughness model has been verified to monitor the in-process predicted surface roughness at 95% confident level. All those parameters have their own characteristics to the arithmetic surface roughness and the surface roughness. It has been proved by the cutting tests that the proposed and developed in-process surface roughness model can be used to predict the in-process surface roughness by utilizing the cutting force ratio with the highly acceptable prediction accuracy.

scholarly journals Analysis of the compromise between cutting tool life, productivity and roughness during turning of C45 hardened steel

2021 ◽  
Vol 27 (1) ◽  
pp. 30-35
Author(s):  
Youcef Abidi
Keyword(s):  
Surface Roughness ◽  
Surface Quality ◽  
Tool Life ◽  
Cutting Tool ◽  
Cutting Speed ◽  
Hardened Steel ◽  
Coefficient Of Determination ◽  
Depth Of Cut ◽  
Machining Productivity ◽  
Mixed Ceramic

Abstract Tool wear and surface roughness as performance indexes are considered to be the most important in terms of hardened materials’ machinability. The best combination of cutting parameters which enhances the compromise between tool life, productivity and machined surface quality contribute to benefice on production cost, which makes manufacturing industry interested in it. The aim of this research is to investigate the life of ceramic cutting tool and machining productivity together with surface roughness during turning of hardened steel C45, with focus on the selection of the optimal cutting parameter combination. The experiments are carried out based on uni-factorial planning methodology of cutting speeds and feed rates. The results show that the mixed ceramic tool is suitable for turning hardened steel C45 (40 HRC) and the conclusion is that it performed well in terms of tool life, productivity and surface quality at a combination of cutting speed (200 m/min), feed (0.08 mm/rev) and depth of cut (0.3 mm). Additionally, a tool life model has been proposed which is presented very high coefficient of determination.

Sign in / Sign up

Export Citation Format

Share Document