The non-isothermal hot deep drawing of AA5083 aluminum alloy

2020 ◽  
Vol 21 (1) ◽  
pp. 112
Author(s):  
Abozar Barimani Varandi
Keyword(s):  
Aluminum Alloy ◽  
Deep Drawing ◽  
Elevated Temperatures ◽  
Thickness Distribution ◽  
Drawing Ratio ◽  
Limiting Drawing Ratio ◽  
Punch Load ◽  
Aa5083 Aluminum Alloy ◽  
5083 Aluminum Alloy

The present work is focused on the hot deep drawing process for cylindrical 5083 aluminum alloy parts, by superimposing a thermal gradient between the blank center-flange region. The imprtance of application of forming processes at elevated temperatures, in improving the formability, has increasingly attracted attention in recent years. As a case study, the experimental and numerical tests were performed at three speeds (60, 200 and 378 mm min−1) from room temperature (RT) up to 0.9 melting point, inspired by the advent of extraordinary superplastic behavior of AA5083 in hot condition. In particular, the focus was on the effects of forming speed on punch load, thickness distribution, and earing behavior. Finite element simulations were run in order to investigate the limiting drawing ratio and temperature gradient. The tests highlight that by increasing the temperature, the number and the position of the ears are constant, while the height of ears decreases. Furthermore, limiting drawing ratio equal to 2.84 is reached at 550 °C.

An Analysis of Forming Limit for Various Arc Radii of Punch in Micro Deep Drawing of the Square Cup

2012 ◽  
Vol 433-440 ◽  
pp. 660-665
Author(s):  
Fung Huei Yeh ◽  
Ching Lun Li ◽  
Kun Nan Tsay
Keyword(s):  
Deep Drawing ◽  
Thickness Distribution ◽  
Forming Limit Diagram ◽  
Experimental Results ◽  
Forming Limit ◽  
Drawing Ratio ◽  
Micro Deep Drawing ◽  
Punch Load ◽  
Explicit Dynamic ◽  
Good Agreement

This paper presents an explicit dynamic finite element method (FEM) in conjunction with the forming limit diagram (FLD) to analyze the forming limit for the various arc radii of punch in micro deep drawing of square cup. In the present study, the tensile test and friction test are performed to obtain the material parameters of the electro-deposited copper foil according to the ASTM standards. Importing these properties, the numerical analysis is conducted by the explicit dynamic FEM. The FLD in numerical simulation is used as the criterion of the forming limit in micro deep drawing of the square cup. The forming limit, deformed shape, punch load-stroke relationship, height of cup and thickness distribution of square cup, are discussed and compared with the experimental results. It shows that a good agreement is achieved from comparison between simulated and experimental results. When the arc radii of punch increase with Rp=0.2, 0.5 and 0.8mm, the limit drawing ratio increases from 1.90 to 2.03 and 2.10. The forming limit of square cup increases with an increase of the arc radii of punch. From this investigation, the results of this paper can be used as reference in the relative researches and applications of micro forming.

Improved Formability and Deep Drawing of Cross-Rolled Magnesium Alloy Sheets at Elevated Temperatures

2005 ◽  
Vol 488-489 ◽  
pp. 461-464 ◽  
Author(s):  
Yong Chao Xu ◽  
Shi Hong Zhang ◽  
H.M. Liu ◽  
Z.T. Wang ◽  
W.T. Zheng ◽  
...  
Keyword(s):  
Magnesium Alloy ◽  
Deep Drawing ◽  
Elevated Temperatures ◽  
Rolling Direction ◽  
Alloy Sheet ◽  
Rolled Sheet ◽  
Drawing Ratio ◽  
Cross Rolling ◽  
Magnesium Alloy Sheet ◽  
Cylindrical Cup

The extruded sheets were prepared at the temperature between 350ıand 400ı, and the magnesium alloy sheet was manufactured by a new method, cross rolling, in which the rolling direction was changed in each pass. At the time, deep drawing of magnesium alloy sheet was investigated at elevated temperatures. The results show that the sheet has refined-grain by cross-rolling after it was annealed at 250ı, and the formability is significantly improved at lower temperatures, which is superior to the extruded sheet and the one-way rolled sheet. Deep drawing of magnesium alloy was performed successfully, and cylindrical cup of limited drawing ratio (LDR) 2.6 and 35 mm deep rectangular box (65ı50) was achieved at the lower temperature of 170ı. The different types of fracture were analyzed and reasonable parameters were determined.

The Prediction of Press Loads in Deep Drawing With Various Conditions of Lubrication at Elevated Temperatures

1973 ◽  
Vol 95 (3) ◽  
pp. 895-903 ◽  
Author(s):  
M. H. Pope ◽  
J. T. Berry
Keyword(s):  
Experimental Work ◽  
Work Hardening ◽  
Deep Drawing ◽  
Numerical Evaluation ◽  
Elevated Temperatures ◽  
Drawing Process ◽  
Deep Drawing Process ◽  
Punch Load ◽  
Die Profile ◽  
Logical Extension

The present work is introduced and is shown to be a logical extension of work by Chung and Swift, Ray and Berry, et al. The authors introduce the deep drawing process and analyze the stresses due to radial drawing (including friction), bending the sheet, unbending the sheet, and die profile friction. From these stresses, an expression for the total punch load is developed. The authors also describe the experimental work in which determinations are made of the work hardening exponents, the anisotropic coefficients, the friction coefficients, and the total punch load. The paper concludes by comparing the numerical evaluation of the maximum punch load with that determined from experiments.

scholarly journals Finite element analysis of deep drawing

2019 ◽  
Vol 11 (9) ◽  
pp. 168781401987456 ◽  
Author(s):  
Dyi-Cheng Chen ◽  
Li Cheng-Yu ◽  
Yu-Yu Lai
Keyword(s):  
Finite Element Analysis ◽  
Plastic Deformation ◽  
Finite Element ◽  
Aluminum Alloy ◽  
Deep Drawing ◽  
Drawing Ratio ◽  
Element Analysis ◽  
Forming Mechanism ◽  
Analysis Process ◽  
Plastic Flow Stress

With the advancement of technology, aiming for achieving a greater lightness and smaller size of 3C products, parts processing technology not only needs to explore the basic scientific theory of materials but also needs to discuss the process of deep drawing numerical and the plastic deformation. This study is based on the square shape of the deep drawing numerical simulation, and aluminum alloy plastic flow stress was input into the finite element method for simulation of plastic deformation in the aluminum alloy friction, mold clamping force, and frequency, as well as amplitude in the influence of forming mechanism and the drawing ratio of aluminum alloy. Finite element analysis software has the function of grid automatic rebuild, which can rebuild the broken grid in the analysis into a complete grid shape, which can avoid the divergence caused by numerical calculation in the analysis process. The greater the obtained error value, the best plastic parameters can be found.

scholarly journals Multi Draw Radius Die Design for Increases in Limiting Drawing Ratio

Metals ◽  
2020 ◽  
Vol 10 (7) ◽  
pp. 870 ◽  
Author(s):  
Wiriyakorn Phanitwong ◽  
Sutasn Thipprakmas
Keyword(s):  
Deep Drawing ◽  
Material Flow ◽  
Rolling Direction ◽  
Die Design ◽  
Drawing Ratio ◽  
Drawing Process ◽  
Deep Drawing Process ◽  
Limiting Drawing Ratio ◽  
Proper Design ◽  
Main Barrier

As a major sheet metal process for fabricating cup or box shapes, the deep drawing process is commonly applied in various industrial fields, such as those involving the manufacture of household utensils, medical equipment, electronics, and automobile parts. The limiting drawing ratio (LDR) is the main barrier to increasing the formability and production rate as well as to decrease production cost and time. In the present research, the multi draw radius (MDR) die was proposed to increase LDR. The finite element method (FEM) was used as a tool to illustrate the principle of MDR based on material flow. The results revealed that MDR die could reduce the non-axisymmetric material flow on flange and the asymmetry of the flange during the deep drawing process. Based on this material flow characteristic, the cup wall stretching and fracture could be delayed. Furthermore, the cup wall thicknesses of the deep drawn parts obtained by MDR die application were more uniform in each direction along the plane, at 45°, and at 90° to the rolling direction than those obtained by conventional die application. In the present research, a proper design for the MDR was suggested to achieve functionality of the MDR die as related to each direction along the plane, at 45°, and at 90° to the rolling direction. The larger draw radius positioned for at 45° to the rolling direction and the smaller draw radius positioned for along the plane and at 90° to the rolling direction were recommended. Therefore, by using proper MDR die application, the drawing ratio could be increased to be 2.75, an increase in LDR of approximately 22.22%.

scholarly journals Achievements in Deep Drawing of Magnesium Alloy Sheets

2011 ◽  
Vol 690 ◽  
pp. 302-305 ◽  
Author(s):  
Lennart Stutz ◽  
Julian Quade ◽  
Michael Dahms ◽  
Dietmar Letzig ◽  
Karl Ulrich Kainer
Keyword(s):  
Magnesium Alloy ◽  
Deep Drawing ◽  
Elevated Temperatures ◽  
Hydraulic Press ◽  
Drawing Ratio ◽  
Transportation Industry ◽  
Specific Strength ◽  
Az31 Sheet ◽  
Dynamic Recrystallisation ◽  
Strength And Stiffness

Magnesium alloy sheets bear significant potential in replacing conventional materials such as aluminium and steels in ultra lightweight designs. High specific strength and stiffness, combined with the lowest density of all structural metals make magnesium alloy sheets candidates to face the challenges of reducing vessel weight in the transportation industry and thus, green house gas emissions. For forming components from sheet metal, deep drawing is a well established and commonly applied process. Due to the limited formability of magnesium sheets at room temperature, deep drawing processes have to be conducted at elevated temperatures. In the present study, hot deep drawing experiments on an industrial scale hydraulic press were successfully conducted. Forming was done at moderately low temperatures from 150°C to 250°C. Sheets of the magnesium alloy AZ31B (Mg-3Al-1Zn-Mn) were drawn to symmetrical cups according to Swift. For AZ31, distinct basal type textures are formed during hot rolling. The influence of texture on earing is displayed. The microstructural evolution of the material is dominated by the formation of twins and dynamic recrystallisation. By optimising the process, a drawing ratio of 2.9 was achieved for AZ31 sheet, outperforming conventional materials at ambient temperature.

Investigation into Influence of Pre-Forming Depth on Multi-Stage Hydrodynamic Deep Drawing of Thin-Wall Cups with Stepped Geometries

2012 ◽  
Vol 457-458 ◽  
pp. 1219-1222 ◽  
Author(s):  
Yu Zhu ◽  
Min Wan ◽  
Ying Ke Zhou ◽  
Qing Hai Liu ◽  
Nan Song Zheng ◽  
...  
Keyword(s):  
Deep Drawing ◽  
Failure Modes ◽  
Thickness Distribution ◽  
Steel Part ◽  
Drawing Ratio ◽  
Thin Wall ◽  
Forming Process ◽  
Hydrodynamic Deep Drawing ◽  
Multi Stage ◽  
Thin Walled

Hydrodynamic deep drawing (HDD) is an effective method for manufacturing complicated and thin-walled parts. Aiming at the forming process of the stainless steel part with 0.4 mm thick and complex stepped geometries, the technology scheme of multi-stage HDD assisted by conventional deep drawing (CDD) is proposed in consideration of wrinkling and destabilization in the unsupported region of the conical wall, and finite element models are built. As a key process parameter, pre-forming depth on the quality of the parts is explored with assistance of numerical simulations and verification experiments. Furthermore, the failure modes, including wrinkling and fracture during forming process are discussed; meanwhile, the optimum pre-forming depth is realized. The results indicate that the technological method is proven to be feasible for integral forming of thin-walled parts with a large drawing ratio and stepped geometries; moreover, the parts with uniform thickness distribution and high quality are successfully formed by adopting optimum pre-forming depth.

Investigations on the Effect of Ultrasonic Vibration in Cylindrical Cup Drawing Processes

2014 ◽  
Vol 622-623 ◽  
pp. 1152-1157 ◽  
Author(s):  
Sang Woo Kim ◽  
Young Seon Lee
Keyword(s):  
Ultrasonic Vibration ◽  
Deep Drawing ◽  
High Frequency Oscillation ◽  
Drawing Ratio ◽  
Experimental Apparatus ◽  
Punch Load ◽  
Cold Rolled ◽  
Cylindrical Cup ◽  
Parametric Analyses ◽  
Cup Drawing

This paper presents experimental and numerical investigations on the effect of ultrasonic vibration on cylindrical cup drawing processes of a cold rolled steel sheet (SPCC). An experimental apparatus to superimpose high frequency oscillation on deep drawing processes was constructed by installing ultrasonic vibration generators consist of piezoelectric transducer and resonator to the die. Conventional and vibration-assisted cylindrical deep drawing tests were carried out for various drawing ratios, and the limiting drawing ratio (LDR) was compared. In order to evaluate the contribution of ultrasonic vibration to the reduction of friction between tools and a material quantitatively, finite element analyses were carried out. Through a series of parametric analyses, friction coefficients which minimize the differences of punch load histories between the experiment and simulation were determined. The results showed that the application of ultrasonic vibration make for improving LDR by reducing the friction between tools and the material, effectively.

Influencing Factors of AZ31B Sheet Deep Drawing

2011 ◽  
Vol 189-193 ◽  
pp. 88-91
Author(s):  
Jun Gao ◽  
Zhen Ming Yue ◽  
Shu Xia Lin
Keyword(s):  
Numerical Simulation ◽  
Deep Drawing ◽  
Experimental Approach ◽  
Elevated Temperatures ◽  
Heating Temperature ◽  
Thickness Distribution ◽  
Simulation Software ◽  
Forming Limit ◽  
Forming Process ◽  
Specific Strength

Magnesium alloys have been attracting much more attentions due to its low density, high specific strength and its lightweight during the past 30 years. In this paper, the deep drawing performance of AZ31B magnisium alloy sheets at elevated temperature was studied by the experimental approach. The results indicated that the formability of the AZ31B sheets at elevated temperatures could be improved significantly. The best external forming parameters can be obtained such as heating temperature of sheet, die-punch clearance, punch fillet radius, etc. Simulating the forming process by using the numerical simulation software, we investigated the stress-strain distribution, thickness distribution and forming limit, etc. The thickness distribution by the numerical simulation agrees well with the experimental results.

Sign in / Sign up

Export Citation Format

Share Document