scholarly journals Effect of the thickness reduction of specimens on the limit strains in thermomechanical tensile tests for hot-stamping studies

2018 ◽  
Vol 5 ◽  
pp. 11
Author(s):  
Connor Lane ◽  
Zhutao Shao ◽  
Kailun Zheng ◽  
Jianguo Lin
Keyword(s):  
Axial Strain ◽  
Hot Stamping ◽  
Tensile Tests ◽  
Thickness Reduction ◽  
Uniaxial Tensile ◽  
Testing System ◽  
Biaxial Testing ◽  
Forming Limits ◽  
Dog Bone ◽  
Selection Of

Sheet metal formability under hot stamping conditions has been evaluated using a novel planar testing system developed previously, being used within a Gleeble machine. Nevertheless, the specimen design with the central recess was not standardised, and the thickness reduction was not applied to the dog-bone type of specimen for testing at the uniaxial straining state. In this paper, effect of thickness reduction of dog-bone specimens on limit strain measurement under hot stamping conditions is investigated, and two types of dog-bone specimens without and with central recess are presented. Thermomechanical uniaxial tensile tests were performed at various deformation temperatures and strain rates, ranging from 370–510 °C and 0.01–1/s, respectively, by using the developed biaxial testing system in the Gleeble. The distributions of temperature and axial strain along gauge region of the two types of specimen were measured and compared. The specimen with consistent thickness had a better uniformity of temperature and strain distributions, compared to that with thickenss reduction. Forming limits for both types of specimen were also determined using the section-based international standard method. It is found that the accuracy of the calculation of forming limits based on the use of specimen with thickness reduction was highly dependent on the selection of the stage of the deformation of the specimen.

scholarly journals Determination of Forming Limits Based on Finite Element Simulations

2021 ◽  
Author(s):  
Fuhui Shen ◽  
Kai Chen ◽  
Junhe Lian ◽  
Sebastian Münstermann
Keyword(s):  
Finite Element ◽  
Damage Mechanics ◽  
Tensile Tests ◽  
Finite Element Simulations ◽  
Experimental Results ◽  
Uniaxial Tensile ◽  
Anisotropic Plasticity ◽  
Forming Limits ◽  
Dog Bone ◽  
Spatio Temporal

Two categories of experiments have been performed to obtain the experimental forming limits of a ferritic stainless steel from uniaxial to equibiaxial tension, including Nakajima tests and tensile tests of flat specimens with different geometries of the central hole as well as the notched dog bone. The plasticity behavior of the investigated material is described using an evolving non-associated anisotropic plasticity model, which is calibrated based on experimental results of uniaxial tensile tests along different loading directions. A damage mechanics model is calibrated and validated based on the global force and displacement response of tensile tests. Finite element simulations of the Nakajima tests and the tensile tests of various geometries have been performed using the anisotropic material model. A novel spatio-temporal method is developed to evaluate the forming limits under different stress states by quantitatively characterizing the plastic strain distribution on the specimen surface. The forming limits have been independently determined from finite element simulation results of tensile specimens and Nakajima specimens using the spatio-temporal evaluation method. The forming limits obtained from numerical simulations of these two types of experiments are in good agreement with experimental results.

scholarly journals Measurement and Analysis of Heterogeneous Strain Fields in Uniaxial Tensile Tests for Boron Steel Under Hot Stamping Conditions

2020 ◽  
Vol 60 (9) ◽  
pp. 1289-1300
Author(s):  
R. Zhang ◽  
Z. Shao ◽  
J. Lin ◽  
T. A. Dean
Keyword(s):  
Temperature Gradient ◽  
Hot Stamping ◽  
Tensile Tests ◽  
Gauge Length ◽  
Image Correlation ◽  
Effect Of Temperature ◽  
Uniaxial Tensile ◽  
Boron Steel ◽  
Strain Fields ◽  
Dog Bone

Abstract Background A significant amount of uniaxial tensile tests has been carried out using Gleeble systems to investigate the viscoplastic deformation of boron steel (22MnB5) under hot stamping conditions. However, due to heat loss through the end clamps, a temperature gradient in the reduced parallel section of dog-bone shaped specimens is inevitable. Objective In the work reported in this paper, the effect of temperature gradient on measured outcomes is examined. Methods Uniaxial tensile tests on 1.5 mm thick boron steel specimens are carried out, under hot stamping conditions and strain fields are quantified using the digital image correlation (DIC) technique. The effect of gauge length on the properties of boron steel, as calculated from observed test results, is determined. Results Compared with the test at room temperature, a bell-shaped strain distribution occurs within the gauge length even before the appearance of the maximum load. Also, average strain within the gauge length, especially in the later stages, changes with gauge length within the investigated range, and thus, different engineering stress-strain curves and fracture strains are determined. In addition, normalized strain rate is significantly dependent on gauge length, which results in over 16% difference among the computed flow stresses by using a unified constitutive model. Conclusions The characterized properties of the material are dependent on gauge length and thus, a testing standard for measuring thermal-mechanical data of materials by using a Gleeble need to be defined.

Functional Gradation in Precipitation Hardenable AA7075 Alloy by Differential Cooling Strategies

2021 ◽  
Vol 883 ◽  
pp. 159-166
Author(s):  
Emad Scharifi ◽  
Moritz Roscher ◽  
Steffen Lotz ◽  
Ursula Weidig ◽  
Eric Jägle ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Phase Particle ◽  
Hot Stamping ◽  
Aging Treatment ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Material Strength ◽  
Second Phase ◽  
Contrast Imaging ◽  
Forming Tools

Inspired by steel forming strategies, this study focuses on the effect of differential cooling on mechanical properties and precipitation kinetics during hot stamping of high strength AA7075 alloy. For this aim, different forming strategies were performed using segmented and differentially heated forming tools to provide locally tailored microstructures. Upon processing, uniaxial tensile tests and hardness measurements were used to characterize the mechanical properties after the aging treatment. Microstructure investigations were conducted to examine the strengthening mechanisms using the electron channeling contrast imaging (ECCI) technique in a scanning electron microscope (SEM). Based on the obtained results, it can be deduced that the tool temperatures play a key role in influencing the mechanical properties. Lower tool temperatures result in higher material strength and higher tool temperatures in lower mechanical properties. By changing the cooling rate with the use of differently heated forming tools, the mechanical properties can be controlled. Microstructure investigations revealed the formation of very fine and homogeneously distributed particles at cooled zones, which were associated with elevated mechanical properties due to the suppression of second phase particle formation during cooling. In contrast, coarse particles were observed at lower cooling rates, explaining the lower material strength found in these zones.

scholarly journals Investigation of diffusion behavior of carburized sheet metal in hot stamping

2019 ◽  
Vol 6 ◽  
pp. 16
Author(s):  
Alexander Horn ◽  
Marion Merklein
Keyword(s):  
Mechanical Properties ◽  
Sheet Metal ◽  
Lightweight Design ◽  
Hot Stamping ◽  
Carbon Diffusion ◽  
Tensile Tests ◽  
Process Window ◽  
Uniaxial Tensile ◽  
Body Parts ◽  
Passenger Safety

Today, manufacturing of structural car body parts faces several challenges, like forming accuracy, passenger safety and lightweight design. One possibility to fulfill these partially rivalling demands is the application of hot stamped components. The combination of hot forming and in-die quenching reduces not only springback, but also results in tensile strengths of more than 1500 MPa. Besides conventional hot stamping, the process can be adapted to manufacture parts with tailored properties. One of the biggest issues of these state-of-the-art processes is the formation of extensive transition zones due to heat transfer. A promising approach to adjust the mechanical properties with a minimized transition zone is tailored carburization of sheet metal. Therefore, the parts are locally coated with graphite, heat treated and subsequently quenched. In this work, the time variant process of carbon diffusion is investigated. Sheets with two different thicknesses are carburized and quenched. The resulting mechanical properties are analyzed using uniaxial tensile tests and microhardness measurements. On this basis, a process window is identified. Furthermore, the applicability of EDX and WDX analysis for the measurement of carbon concentration is investigated within this work.

scholarly journals Investigation of diffusion behavior of carburized sheet metal in hot stamping

2018 ◽  
Vol 190 ◽  
pp. 08004 ◽  
Author(s):  
Alexander Horn ◽  
Marion Merklein
Keyword(s):  
Mechanical Properties ◽  
Transition Zone ◽  
Sheet Metal ◽  
Lightweight Design ◽  
Hot Stamping ◽  
Sheet Thickness ◽  
Carbon Diffusion ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Body Parts

Today’s manufacturing of structural car body parts faces several challenges, like forming accuracy and passenger safety. Besides these two requirements, lightweight design plays an important role. One possibility to fulfill these partially rivalling demands is the application of hot stamped parts. The combination of hot forming and in die quenching reduces not only springback, but also results in tensile strengths of up to 1500 MPa. This makes a simultaneous reduction of sheet thickness and therefore weight reduction possible. Further development enabled a tailored adjustment of mechanical properties, for example by applying different cooling conditions along the parts. One of the biggest issues of these state of the art processes is the formation of a transition zone due to heat transfer. A promising approach to adjust the mechanical properties with a minimized transition zone is the carburization of sheet metal. Therefore, the parts are coated with graphite, heat treated and subsequently quenched. In this work, the time variant process of carbon diffusion is investigated. Sheets with two different thicknesses are carburized and quenched. The resulting mechanical properties are analyzed using uniaxial tensile tests and microhardness measurements. The results are correlated with the carbon content measured by EDX-analysis.

scholarly journals The influence of sample geometry and size on porcine aortic material properties from uniaxial tensile tests using custom-designed tissue cutters, clamps and molds

PLoS ONE ◽  
2021 ◽  
Vol 16 (2) ◽  
pp. e0244390
Author(s):  
Ming Pei ◽  
Donghua Zou ◽  
Yong Gao ◽  
Jianhua Zhang ◽  
Ping Huang ◽  
...  
Keyword(s):  
Material Properties ◽  
Tensile Testing ◽  
Tensile Tests ◽  
Optimal Choice ◽  
The Other ◽  
Uniaxial Tensile ◽  
Test Results ◽  
Uniaxial Tensile Testing ◽  
Dog Bone ◽  
Weibull Theory

The aim of this study was to identify the influence of specimen geometry and size on the results of aortic uniaxial tensile tests using custom-designed tissue cutters, clamps and molds. Six descending thoracic aortas from pigs were used for rectangular sample tests, in which the circumferential and axial specimens had widths of 6 mm, 8 mm and 10 mm. The other six aortas were used for the dog-bone-shaped sample tests and were punched into circumferential, axial and oblique specimens with widths of 2 mm, 4 mm and 6 mm. We performed uniaxial tensile tests on the specimens and compared the test results. The results showed that mid-sample failure occurred in 85.2% of the dog-bone-shaped specimens and in 11.1% of the rectangular samples, which could be caused by Saint-Venant’s principle. Therefore, rectangular specimens were not suitable for aortic uniaxial tensile testing performed until rupture. The results also showed that the size effect of the aorta conformed to Weibull theory, and dog-bone-shaped specimens with a width of 4 mm were the optimal choice for aortic uniaxial tensile testing performed until rupture.

scholarly journals Full-Field Temperature Measurement of Stainless Steel Specimens Subjected to Uniaxial Tensile Loading at Various Strain Rates

Materials ◽  
2021 ◽  
Vol 14 (18) ◽  
pp. 5259
Author(s):  
Krzysztof Żaba ◽  
Tomasz Trzepieciński ◽  
Stanislav Rusz ◽  
Sandra Puchlerska ◽  
Maciej Balcerzak
Keyword(s):  
Stainless Steel ◽  
Strain Rate ◽  
Strain Hardening ◽  
Heat Generation ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Strain Hardening Exponent ◽  
Strain Rates ◽  
Full Field ◽  
Dog Bone

This article presents a study on the effect of strain rate, specimen orientation, and plastic strain on the value and distribution of the temperature of dog-bone 1 mm-thick specimens during their deformation in uniaxial tensile tests. Full-field image correlation and infrared thermography techniques were used. A titanium-stabilised austenitic 321 stainless steel was used as test materials. The dog-bone specimens used for uniaxial tensile tests were cut along the sheet metal rolling direction and three strain rates were considered: 4 × 10−3 s−1, 8 × 10−3 s−1 and 16 × 10−3 s−1. It was found that increasing the strain rate resulted in the intensification of heat generation. High-quality regression models (Ra > 0.9) developed for the austenitic 321 steel revealed that sample orientation does not play a significant role in the heat generation when the sample is plastically deformed. It was found that at the moment of formation of a necking at the highest strain rate, the maximum sample temperature increased more than four times compared to the initial temperature. A synergistic effect of the strain hardening exponent and yield stress revealed that heat is generated more rapidly towards small values of strain hardening exponent and yield stress.

Anisotropic Behavior in Plasticity and Ductile Fracture of an Aluminum Alloy

2015 ◽  
Vol 651-653 ◽  
pp. 163-168 ◽  
Author(s):  
Yan Shan Lou ◽  
Jeong Whan Yoon
Keyword(s):  
Plastic Deformation ◽  
Aluminum Alloy ◽  
Ductile Fracture ◽  
Stress Triaxiality ◽  
Tensile Tests ◽  
Uniaxial Tensile ◽  
Anisotropic Plasticity ◽  
Dog Bone ◽  
Associate Flow Rule ◽  
Anisotropic Plastic

Anisotropic mechanical behavior is investigated for an aluminum alloy of 6K21-IH T4 both in plastic deformation and ductile fracture. Anisotropic plastic deformation is characterized by uniaxial tensile tests of dog-bone specimens, while anisotropy in ductile fracture is illustrated with specimens with a central hole, notched specimens and shear specimens. All these specimens are cut off at every 15º from the rolling direction. The r-values and uniaxial tensile yield stresses are measured from the tensile tests of dog-bone specimens. Then the anisotropic plasticity is modeled by a newly proposed J2-J3 criterion under non-associate flow rule (non-AFR). The testing processes of specimens for ductile fracture analysis are simulated to extract the maximum plastic strain at fracture strokes as well as the evolution of the stress triaxiality and the Lode parameter in different testing directions. The measured fracture behavior is described by a shear-controlled ductile fracture criterion proposed by Lou et al. (2014. Modeling of shear ductile fracture considering a changeable cut-off value for stress triaxiality. Int. J. Plasticity 54, 56-80) for different loading directions. It is demonstrated that the anisotropic plastic deformation is described by the J2-J3 criterion with high accuracy in various loading conditions including shear, uniaxial tension and plane strain tension. Moreover, the anisotropy in ductile fracture is not negligible and cannot be modeled by isotropic ductile fracture criteria. Thus, an anisotropic model must be proposed to accurately illustrate the directionality in ductile fracture.

Strain measurement and error analysis in thermo-mechanical tensile tests of sheet metals for hot stamping applications

2017 ◽  
Vol 232 (11) ◽  
pp. 1994-2008 ◽  
Author(s):  
Zhutao Shao ◽  
Nan Li ◽  
Jianguo Lin ◽  
Trevor A Dean
Keyword(s):  
Error Analysis ◽  
Hot Stamping ◽  
Constant Strain Rate ◽  
Tensile Tests ◽  
Gauge Length ◽  
Temperature Gradients ◽  
Image Correlation ◽  
Uniaxial Tensile ◽  
Heating And Cooling ◽  
Gauge Section

In order to conduct uniaxial tensile tests for hot stamping applications, tests are normally performed by using a Gleeble thermo-mechanical materials simulator so that rapid heating and cooling processes can be obtained. However, temperature gradients in a specimen tested on Gleeble are inevitable due to resistance heating principles and heat loss to grips and water-cooled jaws. In this research, a pair of purpose-built grips made of stainless steel with low thermal conductivity and significantly reduced contacting area for clamping, as well as a flat dog-bone specimen with maximised parallel length (80 mm) were designed, for the purpose of improving the temperature uniformity within the concerned gauge section area of the specimen. Uniaxial tensile tests on AA6082 were performed, after controlled heating and cooling processes, at constant deformation temperatures in the range of 400 ℃–500 ℃ and at constant strain rate in the range of 0.1–4/s, to simulate its hot stamping conditions. The digital image correlation system was adopted to enable strain distributions in specimens to be measured. The temperature distributions in specimens were investigated and an effective gauge length of 14 mm was specified accordingly to ensure temperature gradients less than 10 ℃ within it at all tested temperatures. True stress–true strain curves of AA6082 were obtained based on results of strain measurements along the defined effective gauge length and used to calibrate a set of advanced material model. Error analysis was carried out by using thermo-electrical and thermo-mechanical FE models on ABAQUS, in which the calibrated material constitutive equations were implemented via subroutines. The error of stress–strain curves of AA6082 measured based on the specified gauge length was investigated and quantified by analysing the distribution of axial strain and axial stress.

Sign in / Sign up

Export Citation Format

Share Document