Effects Of Short Time High Shear Exposure Upon Platelet Function And The Coagulation System Under Heparin Anticoagulation

1981 ◽  
Author(s):  
L J Wurzinger ◽  
R Opitz ◽  
P Blasberg ◽  
K Bialonski ◽  
H Schmid-Schönbein

The fact that high shear activates and damages platelets has been suspected to be a major cause of thromboembolism in artificial internal organs (AIO) or in arterial stenosis. In AIO wall shear stresses well above 50 Nm-2 have been computed to which blood cells are exposed for times in the order of milliseconds (ms). Unfortunately, the studies on this subject employing defined flow conditions operate with exposure times higher than 10 seconds. The pupose of the present study was to elucidate the effects of high shear exposure for ms upon platelet function (ADP induced platelet aggregation (PA), platelet procoagulant activity {PF- 3)) under heparin anticoagulation, which is also used in AIO.To apply shear rates ranging from 50 - 220 Nm-2 to heparinized PRP for defined exposure times between 7 - 700 ms a flow through Couette-viscometer was employed. Platelet factor 3 (PF-3) availability was estimated by using a modified Stypven time technique. Lactic dehydrogenase (LDH) liberation was taken as a measure for platelet destruction. All steps of the experimental procedure were carried out at 37°C.From our data we conclude that, in the presence of physiological calcium levels (heparin anticoagulation) shear stresses and exposure times that certainly occur in AIO are able to activate platelets and procoagulant potential of blood.

1976 ◽  
Vol 55 (3) ◽  
pp. 353-356 ◽  
Author(s):  
M. Braden ◽  
Ratna Perera

Six commercial fluoride gels have been studied, using a cone and plate viscometer. Also, the thickening agents have been analyzed using infrared spectroscopy. All gels showed stress thinning, which is the decrease of viscosity with shear rate. Such shear rate dependence is clinically convenient in that the gel will flow readily at the high shear stresses present when the gel is applied but will not flow readily under its own weight when on the tooth. Five materials containing hydroxyalkyl celluloses showed similar degrees of shear thinning. One material with a non-cellulosic thickener showed much more extreme stress thinning together with elastic behavior at low shear rates; such behavior may be clinically advantageous. All of the gels showed only slight temperature dependence of rheological properties.


CORROSION ◽  
1960 ◽  
Vol 16 (7) ◽  
pp. 309t-311t ◽  
Author(s):  
S. W. BRADSTREET

Abstract Several types of coatings may be used for service in extreme thermal environments. For moderate temperatures (to about 1700 C) for short time periods, these coatings may be rather simple refractory layers. Under the more severe conditions of ramjet and rocket operation, reinforced materials, graded substrate-coating interfaces, or multilayers are required. Where thermal gradients are severe and where high shear stresses and abrasion exist, composites must be used which utilize controlled ablation. The principles which appear to dominate the attachment of a ceramic coating to a variety of substrates are reviewed, and the deficiencies and advantages of different combinations are discussed. Principles for “tailoring” protective coatings for refractory metals is suggested, and a flame-sprayed ceramic coating of potential value as a combustion catalyst is used to illustrate these principles. 5.4.2


Blood ◽  
2012 ◽  
Vol 120 (21) ◽  
pp. 3300-3300
Author(s):  
Reginald Tran ◽  
Byungwook AHN ◽  
David R Myers ◽  
Yongzhi Qiu ◽  
Yumiko Sakurai

Abstract Abstract 3300 Background: Hemostasis is an important physiologic process that requires the aggregation of platelets at distinct sites of vascular injury to promote clot formation and prevent blood loss. Platelet response to soluble agonists and shear stress has been studied extensively, but little is known of how microenvironmental geometry affects platelet function. As platelets must quickly adhere to, aggregate, and initiate coagulation only at the affected areas, spatial cues must at some level regulate this process. This aspect of spatial regulation has been investigated under static conditions by our group and others (Kita et al., 2011; Van de Walle et al., 2012). Understanding this aspect of platelet function is vital for better understanding the process of hemostasis and pathophysiological conditions such as thrombosis. Here, we directly examine how spatial cues affect platelet aggregation and physiology under variable shear conditions by flowing heparinized whole blood over micropatterned collagen in a microfluidic channel. This system allows us to assess platelet aggregate morphology under different geometric constraints and shear rates, as well as evaluate platelet physiology at the single cell level by measuring calcium signaling using fluorogenic dyes. Results: A microfluidic channel was bonded to a glass coverslip stamped with FITC-conjugated Type I collagen using a novel technique combining microcontact printing and the stamp-stick bonding technique (Satyanarayana et al., 2005). Before flowing, each chamber was incubated with 1% bovine serum albumin (BSA) blocking solution for 1.5 hours. Whole heparinized blood was then flowed through the chamber at shear rates of 100, 1000, and 10000 s−1. Platelets were labeled with Fura Red, and time lapse confocal imaging was performed for 10 minutes to monitor the aggregation of platelets at the start of flow. The flow chambers were then flushed with Tyrode's buffer with 0.1% BSA using the same experimental shear rates until the chamber was cleared of red blood cells. Image analysis was conducted using ImageJ (to calculate the percentage of platelet coverage on the collagen stamps at different shear rates. Platelets initially adhere to the distal edge of the collagen micropatterns for all shear rates (Fig. 1), indicating that platelets may require a priming region before forming a stable adhesion. As shear rate increased, platelet coverage of the collagen stamps decreased. However, aggregates also grew without conforming to the geometric constraints imposed by the collagen micropatterns more frequently at those higher shear rates (Fig. 1). Though platelet tethers generally aligned in the direction of the flow, increased tether lengths could be seen when platelets were exposed to higher shear, which may explain why platelets were able to span larger gaps and aggregate in a less spatially constrained manner at high shear rates. Image analysis shows that 51.5% of the collagen was covered by platelet aggregates for a shear rate of 100 s−1 with some platelets forming tethers to span gaps (Fig. 2). When the shear rate was increased to 1000 s−1, platelet coverage of the collagen microstamp drastically dropped to 18.5% (Fig. 2). At a pathophysiological shear rate of 10000 s−1, the percentage of collagen covered by platelets dropped further to 12.8% and adopted a linear shape, although a large portion of the aggregate can be seen spanning gaps between the collagen microstamp (Fig. 1 and 2). Conclusions and Ongoing Efforts: Ours is the first reported study of the spatial regulation of platelet aggregation under variable shear in a microfluidic channel. We have found that platelets are more spatially regulated under low shear conditions compared to high shear, which has implications for thrombosis and other clotting disorders. Future studies will incorporate the simultaneous use of ratiometric fluorgenic calcium signaling dyes to investigate the role of spatial regulation in Ca2+ signaling. Finally, we have developed a method to culture endothelial cells around a collagen micropattern to study this spatial regulation of platelet function under more physiological conditions (Fig. 3). Disclosures: No relevant conflicts of interest to declare.


1999 ◽  
Vol 106 (3) ◽  
pp. 777-783 ◽  
Author(s):  
Edith Fressinaud ◽  
Agnès Veyradier ◽  
Marianne Sigaud ◽  
Catherine Boyer-Neumann ◽  
Cécile Le Boterff ◽  
...  

Circulation ◽  
2007 ◽  
Vol 116 (suppl_16) ◽  
Author(s):  
Alexander O Spiel ◽  
Florian B Mayr ◽  
Martin Frossard ◽  
Andreas Kliegel ◽  
Heidrun Losert ◽  
...  

Background: The prognosis of patients with cardiac arrest is still poor, and hardly any specific therapeutic options exist to improve outcome. Platelet activation has been observed in patients undergoing cardiopulmonary resuscitation (CPR). This may contribute to impairment of microcirculatory function and overall poor outcome despite return of spontaneous circulation. Data on direct platelet function in cardiac arrest are scarce. Platelets of patients with myocardial infarction are hyperfunctional, which predicts the degree of myocardial necrosis. Thus, we hypothesized that platelets may be even more hyper-functional in patients whose myocardial infarction causes cardiac arrest. We determined platelet function under high shear rates of patients with cardiac arrest and were further interested whether this may be related to the cause of cardiac arrest. Methods: We conducted a prospective study in 77 cardiac arrest patients at the Emergency Department of a tertiary care hospital. Collagen adenosine diphosphate closure time (CADP-CT) was assessed by the FDA-approved platelet function analyzer (PFA-100). In addition, plasma levels of von Willebrand factor (vWf:RiCo) were measured by turbidometry. Independent staff members of the emergency department not otherwise involved in this trial diagnosed the origin of cardiac arrest. Results: More than half of cardiac arrests were caused by myocardial ischemia. CADP-CT values (54s; 95%CI: 48–60s in 3.8% citrate) were much shorter in these patients as compared to patients with other causes of cardiac arrest (110s; 95%CI: 84–135s, p<0.001). This is substantially less than the 87s (95%CI: 80–94s) in patients with ST-elevation myocardial infarction as previously published. vWf:RiCo levels were substantially increased above the upper normal limit (180 U/dL) in all patient groups. Conclusion: Patients with myocardial ischemia triggered cardiac arrest displayed the highest degree of platelet hyper-function under high shear rates, which was not solely due to increased vWF. Those patients may benefit from a rapid, more aggressive anti-platelet therapy than currently performed or an anti-vWF targeted therapy.


The Eyring theory of viscous flow suggests that lubricating oils should exhibit shear thinning when the shear stress exceeds about 5 MPa. The results of friction experiments in rolling-contact disc machines where very high pressures are generated in the lubricant film support this prediction, but are open to the criticism that the fluid is subjected to a high pressure for such a short time ( ca . 10 -4 s) that an equilibrium state may not be reached. In the present investigation the appropriate condition of the lubricant is achieved, not by subjecting it to very high pressures but by maintaining it in the supercooled state. The lubricant is thus in a condition of equili­brium and the shear experiments are carried out at atmospheric pressure. The lubricant specimen is retained in a suitably adapted split Hopkinson torsion bar, and at the high rates of shear applied ( ca . 10 4 s -1 ) the shear stress at sufficiently low temperatures can exceed 5 MPa. By this tech­nique the shear pulse is applied for a sufficiently short time ( ca . 10 -3 s) to avoid viscous heating of the sample, which bedevils normal viscometry at high shear rates. Two fluids were tested: polyphenyl ether 5P4E and a mineral oil Shell HVI 650. Nonlinearity in the shear-stress-shear-strain-rate relation was found when the stress exceeded about 3 MPa. The elastic shear modulus G ∞ was also measured, yielding ca . 500 MPa for 5P4E and ca . 50 MPa for HVI 650.These values compare with ca . 1100 MPa and 300 MPa as found by the high-frequency oscillating shear technique at small strains.


1999 ◽  
Vol 202 (22) ◽  
pp. 3111-3119 ◽  
Author(s):  
F.I. Thomas ◽  
T.F. Bolton

Shear stresses experienced by eggs in the oviduct of the echinoid Arbacia punctulata during spawning were calculated using engineering equations that describe laminar flow through pipes. Shear stresses in the oviduct ranged from 0 to 58.7 Pa. Two properties of eggs were identified that have the potential either to minimize the shear stress in the oviduct or to reduce the damage experienced by eggs exposed to high shear stress. These properties are the viscosity of the eggs and the presence of extracellular layers on eggs of A. punctulata. The viscosity of eggs decreases with increasing shear rates, which reduces the magnitude of shear stress experienced in the oviduct, while the extracellular layers mitigate the effect of shear stress on the eggs. Eggs with intact extracellular layers were damaged less frequently than were those with the extracellular layers removed. The results of this research indicate that physical stresses may be important selective factors in the evolution of gamete properties.


1990 ◽  
Vol 112 (3) ◽  
pp. 417-425 ◽  
Author(s):  
C. S. Peter Wu ◽  
T. Melodick ◽  
S. C. Lin ◽  
J. L. Duda ◽  
E. E. Klaus

A high-shear capillary viscometer was used to determine the viscosity of mineral oil lubricants containing an olefin copolymer up to shear rates of a million reciprocal seconds. Comprehensive measurements were conducted for a range of polymer concentrations from 1–3 wt percent polymer and a temperature range of 38–120° C. The experimental technique utilizes a theoretical analysis procedure to handle the complications associated with viscous heating, the influence of pressure on the viscosity, and the excess pressure drop which occur at the entrance and exit of the capillary. The viscosity of the polymer solutions is determined over the complete range of shear rate starting from the lower Newtonian limit, through the shear-thinning region, and finally, the Newtonian behavior at high shear rates. It is shown that the standard ASTM plot for viscosity-temperature behavior can be used to correlate the viscous behavior for a given polymer concentration over this broad range of shear rates and shear stresses.


1993 ◽  
Vol 115 (4) ◽  
pp. 640-647 ◽  
Author(s):  
R. Feng ◽  
K. T. Ramesh

A modified torsional Kolsky bar is used to shear a thin annular layer of lubricant held between concentric cylinders. The shear rates obtained range from 4 × 103 to 4 × 104 s−1; the duration of the shear pulse is about 400 microseconds. The shear stress history and the corresponding shear-rate history are deduced using standard torsional Kolsky bar techniques. This experimental technique provides the capability of measuring the shear stresses sustained by fluids at very high shear rates, while the short test duration ensures a minimal rise in temperature due to the associated shear heating. Results are presented for a synthetic lubricant (5P4E) and a mineral oil (HVI650). The lubricants are both observed to be rate-sensitive over the entire range of shear rates examined; the rate-dependence of the shear response is strongly non-Newtonian at high shear rates. Softening during the test is observed for both materials; this softening appears to be largely driven by a thermal mechanism.


Sign in / Sign up

Export Citation Format

Share Document