scholarly journals Effect of In-Office Bleaching on Color and Surface Roughness of Composite Restoratives

2010 ◽  
Vol 04 (02) ◽  
pp. 118-127 ◽  
Author(s):  
Randa Hafez ◽  
Doa Ahmed ◽  
Mai Yousry ◽  
Wafa El-Badrawy ◽  
Omar El-Mowafy
Keyword(s):  
Surface Roughness ◽  
Surface Texture ◽  
Color Change ◽  
Distilled Water ◽  
Bleaching Agent ◽  
Color Changes ◽  
Before And After ◽  
Colorimetric Measurements ◽  
Natural Teeth ◽  
Environmental Sem

Objectives: The purpose of this study was to determine color changes and surface roughness of composites when they were subjected to in-office bleaching.Methods: 12 discs 15 mm in diameter and 2 mm thick were prepared from two shades (A2 & A4) of two composites, Durafil VS (DF) and TPH3 (TPH). Specimens were polished and stored in distilled water for 24 hours at 37°C before being subjected to bleaching, staining, and re-bleaching. Each of the groups of specimens (DF-A2, DF-A4, TPH-A2 and TPH-A4) were subdivided into three subgroups (n=4) and bleached with Beyond, LumaWhite-Plus, and Opalescence-Boost. Specimens were then stained by immersing them in a coffee solution for 48 hours at 37°C, and then they were re-bleached. Colorimetric measurements were performed at baseline, after bleaching, after staining, and after rebleaching. Surface roughness was determined with environmental SEM before and after bleaching. Data were statistically-analyzed.Results: None of the bleaching systems notably changed the color of composites (delta-E<2). Coffee staining affected DF specimens more than TPH. Stained specimens showed variable responses to whitening with no significant color change observed with TPH (delta-E<2) and significant changes observed with DF. Surface roughness significantly changed with bleaching, but the degree varied according to composite shade and bleaching agent.Conclusions: Three in-office bleaching agents had no significant color changes on two composites. DF showed more color change than TPH when immersed in coffee. Stained composites showed different degrees of whitening, with DF showing more response. Bleaching may adversely affect the surface texture of composites. Dentists should take into consideration that composite restorations may not respond to bleaching in the same way that natural teeth do. (Eur J Dent 2010;4:118-127)

scholarly journals The effect of a bleaching agent on the pigment removal and the bond strength of bulk-fill resin composites: an in vitro study

2018 ◽  
Vol 47 (5) ◽  
pp. 298-304
Author(s):  
Caroline de Farias CHARAMBA ◽  
Renally Bezerra Wanderley LIMA ◽  
Sônia Saeger MEIRELES ◽  
Rosângela Marques DUARTE ◽  
Ana Karina Maciel ANDRADE
Keyword(s):  
Bond Strength ◽  
Color Change ◽  
Resin Composite ◽  
Distilled Water ◽  
Filling Material ◽  
Resin Composites ◽  
Bleaching Agent ◽  
Microtensile Testing ◽  
Before And After

Abstract Introduction In order to simplify the technique, reduce the time required for direct adhesive restorations, bulk-fill resin composites have been developed be applied in bulk placement up to 4 mm increments. Objective Evaluating the color change (ΔE) and the microtensile bond strength (μTBS) of bulk fill resin composites (BFRC) to dentin after the immersion in regular beverages and the application of bleaching systems. Method Forty-five human molar teeth were randomly distributed in three groups according to the filling material (n=15): Filtek Bulk Fill, Tetric N Ceram Bulk Fill and Filtek Z100. The restored teeth were immersed in coffee, wine and distilled water (n=5) for 72 hours. The color parameters were measured using a spectrophotometer, having as basis the CIE L*a*b*, before and after tooth staining and application of bleaching processes. Subsequently, the teeth were sectioned to obtain the specimens for the microtensile testing. The ΔE values were analyzed applying the Kruskal-Wallis and the Wilcoxon tests, and the μTBS values were analyzed applying the ANOVA and the Bonferroni tests (p<0.05). Result There were no significant differences in the ∆E values when comparing the BFRCs to the conventional resin composite (CRC) in most of the experimental groups. The ∆E values did not present significant differences before and after the application of bleaching processes for all the tested resin composites. The BFRCs presented higher μTBS values than the CRC after exposure to distilled water, wine and bleaching agent. Conclusion The studied BFRCs presented similar color stability to the CRC. The BFRCs presented higher bond strength to the dentin than the CTC in most of the evaluated conditions. The bleaching agent was not effective in whitening the stained restored teeth.

scholarly journals Can ozone or violet light improve the color change or physicochemical properties of hydrogen peroxide-bleached tooth?

2021 ◽  
Vol 32 (4) ◽  
pp. 19-30
Author(s):  
Nayara Rodrigues Nascimento Oliveira Tavares ◽  
Alexia da Mata Galvão ◽  
Lia Dietrich ◽  
Roberta Furtado Carvalho ◽  
Robinson Sabino Silva ◽  
...  
Keyword(s):  
Hydrogen Peroxide ◽  
Surface Roughness ◽  
Color Change ◽  
Repeated Measure ◽  
Color Changes ◽  
Violet Light ◽  
Atomic Force ◽  
Measure Anova ◽  
Before And After ◽  
To Receive

Abstract: This study investigated the bleaching effectiveness and the physicochemical effects on enamel of violet light and ozone, associate or not to hydrogen peroxide, compared to 35%-hydrogen peroxide. Enamel-dentin blocks from human molars were randomly allocated to receive one of the following bleaching protocols (n=15): (HP) 35%-hydrogen peroxide, (VL) violet light, (OZ) ozone, the association between hydrogen peroxide with ozone (OZ+HP) or violet light (VL+HP). All protocols were performed in two sessions with a 48h interval. Color (spectrophotometer) and mineral composition (Raman spectroscopy) were measured before and after the bleaching. Color changes were calculated by ΔEab, ΔE00, and whitening index (WI). The surface roughness was measured with an atomic force microscope. Data were analyzed by One-way or Two-way repeated measure ANOVA followed by the Tukey’s test (α = 0.05). The lowest color change values (either measured by WI, ΔEab, or ΔE00) were observed for VL and OZ used with no HP. Violet light associate with HP was unable to improve the color changes observed for the peroxide alone, in combination with OZ and HP, the highest color changes were verified. Regardless of bleaching protocol, the bleached enamel presented higher contents of PO4 and CO3 -2 than those observed at baseline. All bleaching protocols resulted in similar enamel surface roughness. Both the VL and the OZ caused reduced effects on the enamel color change when used alone. The ozone therapy improved the bleaching effect in the group that received the association of HP.

scholarly journals Effects of Khat on Surface Roughness and Color of Feldspathic and Zirconia Porcelain Materials under Simulated Oral Cavity Conditions

Medicina ◽  
2020 ◽  
Vol 56 (5) ◽  
pp. 234
Author(s):  
Mohammed M. Al Moaleem ◽  
Rashad AlSanosy ◽  
Nasser M. Al Ahmari ◽  
Mansoor Shariff ◽  
Abdulkhaliq A. Alshadidi ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Computer Aided Design ◽  
Color Stability ◽  
Computer Assisted ◽  
Khat Chewing ◽  
Color Changes ◽  
Before And After ◽  
Cad Cam ◽  
Natural Teeth ◽  
Aided Design

Background and Objectives: Khat chewing is considered as a daily habit that is practiced by more than five million people globally. The effect of khat chewing on the surface roughness and the color stability of natural teeth and the material used in the fabrication of dental prosthesis remains unknown. This study was conducted to explore and compare the effect of khat homogenate (KH) on the surface roughness (Ra) and the average color changes (ΔE*) amongst natural teeth and selected shades from different porcelain types, namely, feldspathic metal ceramic (MC) VM13, computer-aided design/computer assisted manufacture (CAD/CAM) feldspathic (Vitablocs Mark II), and multilayer zirconia (Ceramill Zolid PS) porcelains. Materials and Methods: Seventy samples were prepared from natural teeth, feldspathic MC, CAD/CAM Vitablocs Mark II, and zirconia porcelain. The Ra values were measured using a profilometer and expressed in micrometers, whereas the ΔE* values were measured using VITA Easyshade® V spectrophotometer for all samples before and after frequent immersion and thermocycling in KH for 30 days. The surface topography was used to assess the materials surfaces (glazed or polished) after KH immersion by using a white light interferometry machine. Results: Results revealed that the Ra and the ΔE* values of the different types of tested porcelain were influenced by KH. The order of surface roughness values was glazed or polished MC > polished Zircon > polished Vitablocs Mark II > natural teeth. The lowest ΔE* values were recorded for glazed Vitablocs Mark II and MC, and the values could be arranged as polished zircon > natural teeth > glazed zircon > polished MC > polished Vitablocs Mark II. P values were significantly varied (<0.001) among all the tested groups, except the zircon group (>0.05) for both Ra and ΔE*. Conclusions: KH significantly affected both surface parameter and color of glazed or polished porcelain materials and natural teeth.

scholarly journals Comparative evaluation of the color stability of universal composites

2021 ◽  
Vol 11 (Suppl. 1) ◽  
pp. 234-237
Author(s):  
Merve Gürses ◽  
Nevin Çobanoğlu ◽  
Omar Faez Abdulateef
Keyword(s):  
Comparative Evaluation ◽  
Color Change ◽  
Native Speakers ◽  
Color Stability ◽  
Composite Resins ◽  
Control Group ◽  
Distilled Water ◽  
Color Changes ◽  
Before And After ◽  
Native Speakers Of English

Aim: The aim of this study is to compare the color stability of different universal composites and to evaluate the effects of keeping them in water for 1 week before coloring. Methodology: Filtek Ultimate (FU), Estelite Ʃ Quick (EQ), and Ceram X One (CX) composites were used. The specimens were kept in the dark, dry environment for 24 hours, then polished, and each composite group was divided into 3 groups: the control, the group that was kept in water for 1 week before coloring and coloring (n=7). The samples in the control group were kept in distilled water for 3 weeks. Samples in the coloring group were colored with coffee for 2 weeks (C), and the samples in the last group were kept in water for 1 week and then stained with coffee for 2 weeks (W+C) (n=7). Color measurements for all samples were taken twice, once before and once after the coloring period. The color changes of the samples were measured using the ∆E* parameter, which was calculated with before and after measurements.  Results: For all composite resins, the ΔE values of the samples in the W+C and C groups were significantly higher than those in the control group. When the composites were compared with each other, the differences between the ΔE values of the composites in the control, W+C, and C groups were not statistically significant. For FU and ESQ, at the end of the coloration period, there were no statistically significant differences between the W+C and C groups. However, for CX, the color change of the samples in the W+C group was significantly higher than that in  the C group. Conclusion: Storage in distilled water for 1 week before staining did not reduce the color change values of the samples. Thus, after composite restorations are performed, there is no need to advise patients to avoid staining foods, especially in the first week after restoration.   How to cite this article: Abdulateef OF, Çobanoğlu N, Gürses M. Comparative evaluation of the color stability of universal composites. Int Dent Res 2021;11(Suppl.1):234-7. https://doi.org/10.5577/intdentres.2021.vol11.suppl1.34   Linguistic Revision: The English in this manuscript has been checked by at least two professional editors, both native speakers of English.

scholarly journals Effect of Fluoride Gels on Microhardness and Surface Roughness of Bleached Enamel

2014 ◽  
Vol 8 (1) ◽  
pp. 188-193 ◽  
Author(s):  
Ana L.P China ◽  
Nayara M Souza ◽  
Yasmin do S. B. de L Gomes ◽  
Larissa D Alexandrino ◽  
Cecy M Silva
Keyword(s):  
Hydrogen Peroxide ◽  
Surface Roughness ◽  
Tooth Enamel ◽  
Distilled Water ◽  
Bleaching Agent ◽  
Fluoride Treatment ◽  
Before And After ◽  
Knoop Microhardness ◽  
Roughness Measurements

The effect of bleaching treatments containing added calcium and combined with neutral or acidic fluoride gels on tooth enamel was investigated in vitro through Knoop microhardness (KHN) and surface roughness (SR) measurements. A total of 60 bovine incisors were tested, including 30 for SR measurements and 30 for KHN measurements. The specimens were divided into 12 groups and subjected to a bleaching agent with hydrogen peroxide 35% (Whiteness HP 35% Maxx, FGM) or hydrogen peroxide 35% with calcium (Whiteness HP 35% Blue Calcium, FGM) and a fluoride treatment flugel acidulated phosphate fluoride (APF) or flugel neutral fluoride (NF). Control specimens were submitted to bleaching treatments without fluoride. Microhardness tests were performed using a Knoop indentor. Roughness measurements were obtained using a roughness analyzer. Measurements were obtained before and after treatment. The specimens were stored in distilled water at 37 °C between treatments. The results were analyzed using descriptive and inferential statistics. Treatments using APF combined with 35% HP caused a decrease in microhardness, while NF combined with HP 35% Ca increased the enamel hardness. Fluoride gels did not alter the SR of the bleached enamel.

scholarly journals Analysis of the Influence of Food Colorings in Esthetic Orthodontic Elastomeric Ligatures

2016 ◽  
Vol 10 (1) ◽  
pp. 516-521 ◽  
Author(s):  
Vanessa Dias da Silva ◽  
Eduardo Martinelli S de Lima ◽  
Caroline Dias ◽  
Leandro Berni Osório
Keyword(s):  
Color Change ◽  
Black Tea ◽  
Control Group ◽  
Distilled Water ◽  
Water Control ◽  
Color Changes ◽  
Influence Of Food

Proposition: The purpose of this study was to evaluate in vitro the color changes of esthetic orthodontic elastomeric ligatures of different shades when exposed to four food colorings commonly found in the diet of patients. Materials and Methods: The sample consisted of esthetic orthodontic elastomeric ligatures in the colors pearl, pearl blue, pearl white and colorless, which were immersed for 72 hours in five different solutions: distilled water (control group), coffee, tea, Coca-Cola ® and wine. The color changes of the esthetic orthodontic elastomeric ligatures were measured with the aid of a spectrophotometer, at T1 - as provided by the manufacturer; and T2 - after colorings process. Results: The results indicated that the esthetic orthodontic elastomeric ligatures of all initial hues are susceptible to pigmentation. Among the evaluated colors, all changed the finished look and the color of the samples tested. In ascending order, the color of the samples was as follows: distilled water, Coca-Cola®, black tea, wine and coffee. Conclusion: The substances that have a greater potential for pigmentation in esthetic orthodontic elastomeric ligatures were black tea, wine and coffee, respectively. All shades of esthetic orthodontic elastomeric ligatures are susceptible to color change.

scholarly journals Influence of Mechanical and Chemical Degradation in the Surface Roughness, Gloss, and Color of Microhybrid Composites

2017 ◽  
Vol 18 (4) ◽  
pp. 283-288 ◽  
Author(s):  
Cleidiel AA Lemos ◽  
Silvio J Mauro ◽  
Paulo H dos Santos ◽  
André LF Briso ◽  
Ticiane C Fagundes
Keyword(s):  
Surface Roughness ◽  
Clinical Significance ◽  
Composite Resin ◽  
Color Change ◽  
Wilcoxon Test ◽  
Chemical Degradation ◽  
Color Changes ◽  
Final Data ◽  
Properties Of Materials ◽  
Spearman Test

ABSTRACT Aim The aim of this study was to investigate the association of different degradations on the roughness, gloss, and color changes of microhybrid composites. Materials and methods Ten specimens were prepared for Charisma, Amelogen Plus, Point 4, and Opallis resins. Surfaces were polished and baseline measurements of roughness, gloss, and color were recorded. Specimens were then submitted to chemical and mechanical challenges, and the specimens were reevaluated. Roughness and gloss were analyzed by Kruskal – Wallis and Dunn's test (p < 0.05). Color change (ΔE) was analyzed by one-way analysis of variance and Tukey's tests (p < 0.05). The initial and final data were compared using the Wilcoxon test (p < 0.05). Spearman test checked the correlation between the roughness and gloss (p < 0.05). Results Regarding surface roughness and gloss, there was no difference between composites before challenges. However, all composites showed a significant increase of roughness after challenges, with highest values for Charisma. The gloss was influenced by challenges, evidencing the best gloss for Point 4. Charisma showed the highest value of color change. There was no correlation between surface roughness and gloss for the initial analysis, and after the challenges. Conclusion Composites were influenced by association of challenges, and Charisma showed the highest changes for roughness, gloss, and color. Clinical significance The type of composite resin influenced the properties of materials, which are surface roughness, gloss, and color change. The dentist should be aware of the performance of different brands, to choose the correct required composite resin for each type of patient or region to be restored. How to cite this article Lemos CAA, Mauro SJ, dos Santos PH, Briso ALF, Fagundes TC. Influence of Mechanical and Chemical Degradation in the Surface Roughness, Gloss, and Color of Microhybrid Composites. J Contemp Dent Pract 2017;18(4):283-288.

scholarly journals The Effect of Desensitizing Toothpastes and Coffee Staining on the Optical Properties of Natural Teeth and Microhybrid Resin Composites: An In-Vitro Study

2018 ◽  
Vol 2018 ◽  
pp. 1-7
Author(s):  
Sedanur Turgut ◽  
Hamiyet Kılınç ◽  
Kıvanç Utku Ulusoy ◽  
Bora Bagis
Keyword(s):  
Color Change ◽  
Cetylpyridinium Chloride ◽  
Human Tooth ◽  
Staining Procedure ◽  
Control Group ◽  
Human Teeth ◽  
Color Changes ◽  
Stannous Fluoride ◽  
Color Measurements ◽  
Natural Teeth

Objective. To evaluate the effect of different desensitizing toothpastes and coffee staining on the discoloration rate of natural human tooth and composite materials. Materials and Methods. A total of 56 human teeth and 56 composite specimens were used. After initial color measurements were taken, specimens and teeth were exposed to simulated toothbrushing with six desensitizing toothpastes containing different active ingredients: stannous fluoride, strontium acetate, potassium citrate and hydroxyapatite, cetylpyridinium chloride, arginine, and novamin. Specimens were then exposed to coffee staining. Throughout the staining procedure, the storing solution was refreshed every day and the specimens were brushed with the tested toothpastes. Color measurements and changes were recorded at each stage and analyzed with one-way ANOVA, Dunnett tests, and paired sample t-test (p<0.05). Results. The largest color change was obtained with the stannous fluoride toothpaste after coffee staining for natural teeth (2.6 ΔE00⁎) and composite specimens (3.1 ΔE00⁎). Coffee staining resulted in significant changes for ΔE00⁎ values of all groups, except for natural teeth brushed with a novamin-based (p= 0.06) toothpaste. For composite specimens, only the stannous fluoride and cetylpyridinium chloride-based toothpastes resulted in significant color changes relative to the control group. ΔL⁎ and Δb⁎ values were also increased after staining for all groups (p<0.05). Conclusions. Desensitizing toothpastes alone did not cause perceptible color changes; however, in combination with coffee staining, it tended to increased discoloration for both composites and natural teeth.

scholarly journals Effect of Polymerization Time and Home Bleaching Agent on the Microhardness and Surface Roughness of Bulk-Fill Composites: A Scanning Electron Microscopy Study

Scanning ◽  
2019 ◽  
Vol 2019 ◽  
pp. 1-8
Author(s):  
Zümrüt Ceren Özduman ◽  
Magrur Kazak ◽  
Mehmet Ali Fildisi ◽  
Rümeysa Hatice Özlen ◽  
Evrim Dalkilic ◽  
...  
Keyword(s):  
Surface Roughness ◽  
Microscopy Study ◽  
Electron Microscopy Study ◽  
Rank Test ◽  
Bleaching Agent ◽  
Polymerization Time ◽  
Before And After ◽  
Signed Rank Test ◽  
Bonferroni Test ◽  
Fill Materials

Objective. The aim of this study is to evaluate the microhardness and surface roughness of two different bulk-fill composites polymerized with light-curing unit (LCU) with different polymerization times before and after the application of a home bleaching agent.Materials-Methods. For both microhardness and surface roughness tests, 6 groups were prepared with bulk-fill materials (SonicFill, Filtek Bulk Fill) according to different polymerization times (10, 20, and 30 s). 102 specimens were prepared using Teflon molds (4 mm depth and 5 mm diameter) and polymerized with LCU. 30 specimens (n=5) were assessed for microhardness. Before home bleaching agent application, the bottom/top (B/T) microhardness ratio was evaluated. After bleaching agent application, the microhardness measurements were performed on top surfaces. Roughness measurements were performed in 72 specimens (n=12) before and after bleaching application. Additionally, for SEM analyses, two specimens from all tested groups were prepared before and after bleaching agent application. The data B/T microhardness ratio before bleaching was analyzed by two-way ANOVA and Tukey’s HSD test. The data from the top surface of specimens’ microhardness before and after bleaching were analyzed using Wilcoxon signed-rank test, Kruskal-Wallis, Mann-WhitneyUtests. The data from surface roughness tests were statistically analyzed by multivariate analysis of variance and Bonferroni test (p<0.05).Results. The B/T microhardness ratio results revealed no significant differences between groups (p>0.05). Comparing the microhardness values of the composites’ top surfaces before and after bleaching, a significant decrease was observed exclusively in FB30s (p<0.05). No significant differences in surface roughness values were observed when the groups were compared based on bulk-fill materials (p>0.05) while the polymerization time affected the surface roughness of the SF20s and SF30s groups (p<0.05). After bleaching, surface roughness values were significantly increased in the SF20s and SF30s groups (p<0.05).Conclusion. The clinicians should adhere to the polymerization time recommended by the manufacturer to ensure the durability of the composite material in the oral environment.

scholarly journals Effect of varying thickness and artificial aging on color and translucency of cubic zirconia and lithium disilicate ceramics

2021 ◽  
Vol 24 (3) ◽  
Author(s):  
Heba El-khayat ◽  
Hesham Katamish ◽  
Amr El-Etreby ◽  
Mostafa Aboushahba
Keyword(s):  
Repeated Measures ◽  
Artificial Aging ◽  
Color Change ◽  
Lithium Disilicate ◽  
Hydrothermal Aging ◽  
Cubic Zirconia ◽  
Color Changes ◽  
Varying Thickness ◽  
Before And After ◽  
Parameter Values

Objective: The aim of this study is to evaluate the effect of varying thickness and artificial aging on the color and translucency of cubic zirconia and lithium disilicate ceramics. Material and Methods: A total of 30 square shaped disks (12 mm x 12 mm) were fabricated from the cubic zirconia (Bruxzir Anterior) blank and lithium disilicate blocks (E.max CAD), used in three thicknesses (0.5mm, 0.8mm and 1mm). Portable spectrophotometer Vita Easyshade Advance was used to obtain color coordinates, which were substituted in formulas and used to calculate color change and translucency parameter values before and after aging (thermocycling for lithium disilicate and hydrothermal aging for cubic zirconia). Repeated measures Analysis of Variance (ANOVA) was used to study the effect of ceramic type, thickness, aging and their interaction on mean translucency parameter. Two-way (ANOVA) was used to study the effect of ceramic type, thickness and their interaction on mean color change (E). Results: Statistical analysis showed that E.max CAD HT is more translucent than Bruxzir Anterior. Translucency decreased as thickness increased. There was a statistically significant decrease in TP after aging for both materials. Lithium disilicate showed statistically significant greater E when subjected to aging than cubic zirconia, with both E values being clinically imperceptible. As thickness increased, E decreased. Conclusions: Thickness highly affected translucency and color of ceramics. As thickness increases, translucency parameter decreases and color change becomes less evident. Aging also causes a significant decrease in translucency parameter and induces color change however color changes are imperceptible. Keywords Aging; Ceramics; Color; Translucency.

Sign in / Sign up

Export Citation Format

Share Document