Design of a tunable electromagnetic vibration absorber for transient vibration suppression under impulse

2021 ◽  
Vol 92 (12) ◽  
pp. 125103
Author(s):  
Xi Wang ◽  
Zhenyuan Xu ◽  
Dida Wang
Keyword(s):  
Vibration Suppression ◽  
Vibration Absorber ◽  
Transient Vibration ◽  
Electromagnetic Vibration

Design and experimental verification of self-powered electromagnetic vibration suppression and absorption system for in-wheel motor electric vehicles

2021 ◽  
pp. 107754632110144
Author(s):  
Ruochen Wang ◽  
Yu Jiang ◽  
Renkai Ding ◽  
Wei Liu ◽  
Xiangpeng Meng ◽  
...  
Keyword(s):  
Electric Vehicles ◽  
Vibration Suppression ◽  
The Self ◽  
Magnetorheological Damper ◽  
Vibration Absorber ◽  
Absorption System ◽  
Dynamic Vibration Absorber ◽  
Dynamic Vibration ◽  
Electromagnetic Vibration ◽  
Self Powered

A self-powered electromagnetic vibration suppression and absorption system integrated with a magnetorheological damper and a linear motor is designed to attenuate the negative effect of vertical vibration caused by the increased unsprung mass for in-wheel motor electric vehicles in this article. The magnetorheological damper is used as a suspension damper to suppress body vibration, and linear motor is used as a dynamic vibration absorber, namely, linear electromagnetic dynamic vibration absorber, to absorb tire vibration, and regenerates the vibration power to drive the magnetorheological damper, realizing self-power. Based on power flow theory, the power transfer mechanism of the vertical vibration for in-wheel motor electric vehicles and the regeneration potential are analyzed. The negative effect on the dynamic performance of in-wheel motor electric vehicles is analyzed through the root mean square of dynamic responses. Moreover, the specific structure scheme of the self-powered electromagnetic vibration suppression and absorption system is provided. The influence of system mass, stiffness, and damping of the linear electromagnetic dynamic vibration absorber on the dynamic performance is analyzed, and these parameters are optimized by particle swarm optimization. Simulation results show that in comparison with a passive damper, the self-powered electromagnetic vibration suppression and absorption system can reduce the body acceleration by 17.05%, which is better than the magnetorheological damper (10.08%). The self-powered electromagnetic vibration suppression and absorption system increases the tire dynamic load by 5.62%, but it is 8.68% less than the magnetorheological damper. Additionally, the regenerated power can offset the consumed power adequately to realize self-power. Finally, a bench test is conducted to verify the effectiveness and feasibility of the self-powered electromagnetic vibration suppression and absorption system.

Design of a slender turning cutting tool via a vibration absorber equipped with piezoelectric ceramic

2021 ◽  
pp. 107754632110144
Author(s):  
Yiqing Yang ◽  
Haoyang Gao ◽  
Qiang Liu
Keyword(s):  
Piezoelectric Ceramic ◽  
Cutting Tool ◽  
Vibration Suppression ◽  
Equations Of Motion ◽  
Electrical Energy ◽  
Diameter Ratio ◽  
Vibration Absorber ◽  
Machined Surface ◽  
Structural Part ◽  
Machined Surface Roughness

Turning cutting tool with large length–diameter ratio has been essential when machining structural part with deep cavity and in-depth hole features. However, chatter vibration is apt to occur with the increase of tool overhang. A slender turning cutting tool with a length–diameter ratio of 7 is developed by using a vibration absorber equipped with piezoelectric ceramic. The vibration absorber has dual functions of vibration transfer to the absorber mass and vibration conversion to the electrical energy via the piezoelectric effect. Equations of motion are established considering the dual damping from the piezoelectric ceramic and rubber gasket. The equivalent damping of piezoelectric ceramic is derived, and the geometries are optimized to achieve optimal vibration suppression. The modal analysis demonstrates that the cutting tool with the vibration absorber can reach 80.1% magnitude reduction. Machining tests are carried out in the end. The machining acceleration and machined surface roughness validate the vibration suppression of the VA, and the output voltage by the piezoelectric ceramic demonstrates the ability of vibration sensing.

The Influence Region Analysis for the Delayed Resonator Vibration Absorber

2001 ◽  
Author(s):  
Giulio Grillo ◽  
Nejat Olgac
Keyword(s):  
Vibration Suppression ◽  
Vibration Absorber ◽  
Primary System ◽  
Frequency Interval ◽  
Vibration Absorption ◽  
Region Analysis ◽  
The Common ◽  
Resonator Vibration ◽  
Three Degree Of Freedom ◽  
Tuned Vibration Absorber

Abstract This paper presents an influence region analysis for an actively tuned vibration absorber, the Delayed Resonator (DR). DR is shown to respond to tonal excitations with time varying frequencies [1–3]. The vibration suppression is most effective at the point of attachment of the absorber to the primary structure. In this study we show that proper feedback control on the absorber can yield successful vibration suppression at points away from this point of attachment. The form and the size of such “influence region” strongly depend on the structural properties of the absorber and the primary system. There are a number of questions addressed in this paper: a) Stability of vibration absorption, considering that a single absorber is used to suppress oscillations at different locations. b) Possible common operating frequency intervals in which the suppression can be switched from one point on the structure to the others. A three-degree-of-freedom system is taken for as example case. One single DR absorber is demonstrated to suppress the oscillations at one of the three masses at a given time. Instead of an “influence region” a set of “influence points” is introduced. An analysis method is presented to find the common frequency interval in which the DR absorber operates at all three influence points.

scholarly journals Vibration suppression of a car engine frame via tuned vibration absorber design

2020 ◽  
Vol 16 (1/2) ◽  
pp. 13
Author(s):  
Jun Wei Sam ◽  
Hock Khuen Cheow ◽  
Jee u Ho ◽  
Hoon Kiat Ng ◽  
Ai Bao Chai
Keyword(s):  
Vibration Suppression ◽  
Vibration Absorber ◽  
Tuned Vibration Absorber

Modeling and Design of an Inertial Vibration Reflector

1997 ◽  
Vol 119 (1) ◽  
pp. 20-27
Author(s):  
R. G. Longoria ◽  
V. A. Narayanan
Keyword(s):  
Vibration Suppression ◽  
Active Vibration Control ◽  
Low Frequency ◽  
Dominant Frequency ◽  
Prototype System ◽  
Primary System ◽  
Transient Vibration ◽  
Modeling And Analysis ◽  
Reflector System ◽  
Oriented Parallel

This paper presents the modeling and analysis of a novel vibration suppression device. This reflector system exerts inertial forces, induced by tuned pendular motion, to control translational vibration of a primary system. Tuning of the reflector critically depends on the parameters of the pendula and on the rotational speed at which they are spun about an axis oriented parallel to the undesired motion. Consequently, one of its most appealing attributes is this devices’s ability to be tuned to, and thus actively track, the dominant frequency of disturbance forces. The paper describes how governing equations from an integrated physical model are developed using a bond graph approach and then used to derive relations applicable in design of an inertial reflector system. It is shown how the model supports component selection and tradeoff studies as well as simulation. Experimental results from testing of a laboratory realization of a prototype system are used to verify the design and to compare with simulation of a mathematical model. The results from the laboratory demonstrate the ability of the inertial reflector to control steady and transient vibration, and the favorable results suggest extended investigation for active vibration control situations. In particular, applications in low frequency vibration mitigation are promising.

On Adaptive-Passive Vibration Suppression Using Distributed-Parameter Absorbers

2000 ◽  
Author(s):  
Nader Jalili
Keyword(s):  
Vibration Suppression ◽  
Excitation Frequency ◽  
Wide Band ◽  
Distributed Parameter ◽  
Vibration Absorber ◽  
Frequency Bandwidth ◽  
Lumped Mass ◽  
Adaptive Capability ◽  
Active Vibration ◽  
Tuning Strategy

Abstract A semi-active vibration absorber with adaptive capability is presented to improve wide band vibration suppression characteristics of harmonically excited structures. The absorber subsection consists of a double-ended cantilever beam carrying an intermediate lumped mass. The adaptive capability is achieved through concurrent adjustment of the position of the moving mass, along the beam, to comply with the desired optimal performance. If such an absorber is attached to a vibrating body, it effectively absorbs vibrations at all frequencies that belong to the absorber frequency bandwidth. Numerical simulations are provided to verify the effectiveness of the proposed absorption scheme. It is shown that the tuning strategy tries to follow and match the absorber natural frequency with the excitation frequency. The optimally tuned absorber provides considerable vibration suppression improvement over the passive and de-tuned absorbers, for wide band excitation disturbances.

Design of a turning cutting tool with large length–diameter ratio based on three-element type vibration absorber

2020 ◽  
Vol 234 (6-7) ◽  
pp. 1032-1043
Author(s):  
Yiqing Yang ◽  
Haoyang Gao ◽  
Wenshuo Ma ◽  
Qiang Liu
Keyword(s):  
Frequency Response ◽  
Cutting Tool ◽  
Vibration Suppression ◽  
Diameter Ratio ◽  
Vibration Absorber ◽  
Vibration Absorbers ◽  
Target Mode ◽  
Large Length ◽  
Element Type ◽  
Structural Parts

The vibration absorber has been effective in vibration control. From the demand of manufacturing structural parts with a deep hole, the design of a turning cutting tool with large length–diameter ratio is presented. An analytical approach of acquiring frequency response of primary structure equipped with typical single-degree-of-freedom vibration absorbers is formulated, and background modes are incorporated with the purpose of achieving an accurate tuning of vibration absorber. Specifically, the three-element type is investigated as the damping element of the vibration absorber embedded in the cutting tool contributes to the stiffness, although it demonstrates medium performance of vibration suppression according to non-dimensional analysis. The experimentally tuned frequency response function of the turning cutting tool with three-element vibration absorber achieves 87.1% reduction on the amplitude of the target mode. Finally, several configurations of internal turning operations are carried out to validate the design of the vibration absorber.

SEVERAL DESIGN ISSUES ON THE TUNABLE ELECTROMAGNETIC VIBRATION ABSORBER

2005 ◽  
Vol 29 (4) ◽  
pp. 655-668 ◽  
Author(s):  
Jie Liu ◽  
Kefu Liu
Keyword(s):  
Permanent Magnet ◽  
Approximation Error ◽  
Vibration Absorber ◽  
Primary System ◽  
Design Issues ◽  
Cross Sectional ◽  
Magnetic Stiffness ◽  
Electromagnetic Vibration ◽  
Aluminum Beam ◽  
Flux Density Distribution

This paper addresses several design issues related to a newly developed electromagnetic vibration absorber (EMVA). The EMVA consists of a clamped-clamped aluminum beam and a permanent magnet that is embedded in the centre of the beam and placed between two poles of a C-shaped electromagnet. By varying the current of the electromagnet, stiffness of the EMVA can be adjusted instantaneously. The EMVA is capable of suppressing vibration of the primary system excited by a harmonic force with a variable frequency. First a simplified equation is proposed to compute the flux density distribution in the gap of the electromagnet. The approximation error caused by the simplification is investigated. Second, the effect of cross-sectional shapes of the permanent magnet on the variable magnetic stiffness and the constant magnetic stiffness is examined. Finally, the effect of the gap spaces of the electromagnet on the variable magnetic stiffness is studied.

Sign in / Sign up

Export Citation Format

Share Document