High-power rhodamine 6G laser with an extended service life

1983 ◽  
Vol 13 (2) ◽  
pp. 146-150 ◽  
Author(s):  
B A Knyazev ◽  
S V Lebedev ◽  
E P Fokin
Author(s):  
Victor V. SINYAVSKIY

At the initiative of S.P.Korolev, in 1959, Special Design Bureau No.1 (now RSC Energia) established the High-temperature Power Engineering and Electric Propulsion Center which was tasked with development of nuclear electric propulsion for heavy interplanetary vehicles. Selected as the source of electric power was a nuclear power unit based on a thermionic converter reactor, and selected as the engine was a stationary low-voltage magnetoplasmodynamic (MPD) high-power (0.5–1.0 MW) thruster which had thousands of hours of service life. The paper presents the results of extensive efforts in research, development, design, materials science experiments, and tests on the MPD-thruster, including the results of development and 500-hours life tests of an MPD-thruster with a 500-600 kW electric power input that used lithium propellant. The world’s first lithium 17 kW MPD-thruster was built and successfully tested in space. The paper points out that to this day nobody has surpassed the then achievements of RSC Energia neither in thruster output during long steady-state operation, nor in performance and service life. Key words: Martian expeditionary vehicle, nuclear electric rocket propulsion system, electric rocket thruster, magnetoplasmodynamic thruster, lithium, cathode, anode, barium, electric propulsion tests in space.


Author(s):  
Vladimir Panchenko

The scientific work is devoted to the prospect of using frost-resistant solar modules with extended service life of various designs for energy supply of infrastructure facilities of the Arctic zone of Russia. The general characteristic of the region under consideration is given, and its energy specifics, directions of energy development based on renewable energy sources are considered. In the work, frost-resistant planar photovoltaic modules and solar roofing panels with an extended service life for power supply of objects are proposed. For simultaneous heat and electrical generation, frost-resistant planar photovoltaic thermal roofing panels and concentrator solar installation with high-voltage matrix solar modules with a voltage of 1000 V and an electrical efficiency of up to 28% are proposed. The considered solar modules have an extended rated power period due to the use of the technology of sealing solar cells with a two-component polysiloxane compound and are able to work effectively at large negative ambient temperatures and large ranges of its fluctuations.


1996 ◽  
Vol 05 (01) ◽  
pp. 73-88 ◽  
Author(s):  
T. YAMAMOTO ◽  
K. FUJII ◽  
A. TAGAYA ◽  
E. NIHEI ◽  
Y. KOIKE ◽  
...  

Basic characteristics of organic-dye doped polymer optical fibers (DPOFs) are demonstrated. The devices contain laser dye, such as Rhodamine 6G (R6G) and Rhodamine B (RB) in the core region. Firstly, amplification characteristics of DPOF amplifiers (PO-FAs) excited by a pulse-operated, doubled Nd:YAG laser are demonstrated, e.g., a 250 mm-length of RB-POFA gives 1 kW (30 dB) of amplified signal at 591 nm. Next, an all solid state system of RB DPOF laser (POFL) is discussed by numerical simulation and the experimental result of high-power amplified spontaneous emission (ASE) by strong excitation of DPOF is shown.


2012 ◽  
Vol 4 ◽  
pp. 153-160
Author(s):  
De Huai Zeng ◽  
Yuan Liu ◽  
Li Li ◽  
De Gui Yu ◽  
Gang Xu

With the development of high power LED technology, junction temperature as a key factor constrains the performance and the service life of LED, and the main parameter of junction temperature is thermal resistance. Therefore, how to measure the thermal resistance of high power LED quickly and accurately plays an important part in improving the performance and the service life of LED. In this paper the accurate and fast measurement equipment was applied to study the thermal characteristics of high power LED. The forward-voltage based method was conducted to measure the junction temperature of high power. Then, support vector regression (SVR) combined with genetic algorithm (GA) for its parameter optimization, was proposed to establish a model to predict the thermal resistance of high power LED. The prediction performance of GA-SVR was compared with those of BPNN model. The result demonstrated that the estimated errors GA-SVR models, such as Mean Absolute Relative Error (MARE) and Root Mean Squared Errors (RMSE), all are smaller than those achieved by the BPNN applying identical samples.


2020 ◽  
Vol 84 (2) ◽  
pp. 173-176
Author(s):  
V. V. Bliznyuk ◽  
O. I. Koval ◽  
V. A. Parshin ◽  
A. G. Rzhanov ◽  
A. E. Tarasov ◽  
...  

Sign in / Sign up

Export Citation Format

Share Document