Experimental Studies on the Influence of Diesel Engine Operating Parameters on Properties of Emitted Soot Particles

2012 ◽  
Vol 184 (1) ◽  
pp. 1-15 ◽  
Author(s):  
Ulrich Leidenberger ◽  
Wolfgang Mühlbauer ◽  
Sebastian Lorenz ◽  
Sebastian Lehmann ◽  
Dieter Brüggemann
Author(s):  
В. І. Левчук ◽  
В. М. Арендаренко ◽  
О. М. Іванов

Наведені результати експериментального дослі-дження впливу кута випередження впорскуванняпалива на статичні та динамічні властивості ди-зеля з турбонаддувом. На основі знятих швидкіс-них характеристик робочих параметрів дизеля зарізних установочних кутів випередження впорску-вання палива була дана оцінка ступеня впливу до-сліджуваного регульованого параметра на стати-чні властивості двигуна. З аналізу динамічнихрежимів вільного прискорення дизеля, отриманихпри різних характерах зміни кута випередженнявпорскування палива, зроблені висновки про тіснийвзаємозв’язок між моментом початку подачіпалива та якістю заданого перехідного процесу. The results of experimental studies of the effect of advanceangle of fuel injection on the static and dynamic properties of adiesel engine with a turbocharger have been produced. Thedegree of influence of the controlled parameter on the staticproperties of a diesel engine was assessed on the basis of velocity characteristics of operating parameters of diesel at different advance angles of fuel injection. From the analysis of dynamicmodes of the free acceleration of a diesel engine, produced byvarious characters of changing of the advance angle of fuelinjection, conclusions about the close relationship between theonset of the fuel supply and the quality of a given transitionhave been made.


Author(s):  
Petar Kazakov ◽  
Atanas Iliev ◽  
Emil Marinov

Over the decades, more attention has been paid to emissions from the means of transport and the use of different fuels and combustion fuels for the operation of internal combustion engines than on fuel consumption. This, in turn, enables research into products that are said to reduce fuel consumption. The report summarizes four studies of fuel-related innovation products. The studies covered by this report are conducted with diesel fuel and usually contain diesel fuel and three additives for it. Manufacturers of additives are based on already existing studies showing a 10-30% reduction in fuel consumption. Comparative experimental studies related to the use of commercially available diesel fuel with and without the use of additives have been performed in laboratory conditions. The studies were carried out on a stationary diesel engine СМД-17КН equipped with brake КИ1368В. Repeated results were recorded, but they did not confirm the significant positive effect of additives on specific fuel consumption. In some cases, the factors affecting errors in this type of research on the effectiveness of fuel additives for commercial purposes are considered. The reasons for the positive effects of such use of additives in certain engine operating modes are also clarified.


2020 ◽  
pp. 22-30
Author(s):  
SERGEY N. DEVYANIN ◽  
◽  
VLADIMIR A. MARKOV ◽  
ALEKSANDR G. LEVSHIN ◽  
TAMARA P. KOBOZEVA ◽  
...  

The paper presents the results of long-term research on the oil productivity and chemical composition of soybean oil of the Northern ecotype varieties in the Central Non-Black Earth Region. The authors consider its possible use for biodiesel production. Experiments on growing soybeans were carried out on the experimental fi eld of Russian State Agrarian University –Moscow Timiryazev Agricultural Academy (2008-2019) on recognized ultra-early ripening varieties of the Northern ecotype Mageva, Svetlaya, Okskaya (ripeness group 000). Tests were set and the research results were analyzed using standard approved methods. It has been shown that in conditions of high latitudes (57°N), limited thermal resources of the Non-Chernozem zone of Russia (the sum of active temperatures of the growing season not exceeding 2000°С), the yield and productivity of soybeans depend on the variety and moisture supply. Over the years, the average yield of soybeans amounted to 1.94 … 2.62 t/ha, oil productivity – 388 … 544 kg/ha, oil content – 19…20%, the content of oleic and linoleic fatty acids in oil – 60%, and their output from seeds harvested – 300 kg/ha. It has been established that as soybean oil and diesel fuel have similar properties,they can be mixed by conventional methods in any proportions and form stable blends that can be stored for a long time. Experimental studies on the use of soybean oil for biodiesel production were carried out on a D-245 diesel engine (4 ChN11/12.5). The concentrations of toxic components (CO, CHx, and NOx) in the diesel exhaust gases were determined using the SAE-7532 gas analyzer. The smoke content of the exhaust gases was measured with an MK-3 Hartridge opacimeter. It has been experimentally established that the transfer of a diesel engine from diesel fuel to a blend of 80% diesel fuel and 20% lubrication oil leads to a change in the integral emissions per test cycle: nitrogen oxides in 0.81 times, carbon monoxide in 0.89 times and unburned hydrocarbons in 0.91 times, i.e. when biodiesel as used as a motor fuel in a serial diesel engine, emissions of all gaseous toxic components are reduced. The study has confi rmed the expediency of using soybeans of the Northern ecotype for biofuel production.


2012 ◽  
Author(s):  
Wan Mohd Faizal Wan Mahmood ◽  
Antonino LaRocca ◽  
Paul J. Shayler ◽  
Fabrizio Bonatesta ◽  
Ian Pegg

2015 ◽  
Vol 813-814 ◽  
pp. 830-835
Author(s):  
Akkaraju H. Kiran Theja ◽  
Rayapati Subbarao

The drawbacks associated with bio-fuels can be minimized by making modifications to combustion chamber. Modification of combustion chamber is achieved by providing an air gap in between the crown and the body of the piston with the top crown made of low thermal conductivity material. Experimentation is carried on a diesel engine with brass as piston crown material and karanja as test fuel, which is found to be a better alternative fuel based on the tests carried out prior to modification. Investigations are carried out on the performance of the engine with modified combustion chamber consisting of air gap insulated piston with 2 mm air gap with brass crown when fuelled with karanja oil. Comparative studies are made between the two configurations of engine with and without modification at an injection timing of 29obTDC. Performance, heat balance and emission plots are made with respect to brake power. Fuel consumption increased with modification. The mechanical and volumetric efficiencies are similar in both the cases. Indicated and brake thermal efficiencies got reduced with modification. But, it is good to see that HC and CO emissions are showing positive trend. Thus, the present investigation hints the possibility of improvements while making piston modification and providing air gap insulation.


Author(s):  

The necessity of adapting diesel engines to work on vegetable oils is justified. The possibility of using rapeseed oil and its mixtures with petroleum diesel fuel as motor fuels is considered. Experimental studies of fuel injection of small high-speed diesel engine type MD-6 (1 Ch 8,0/7,5)when using diesel oil and rapeseed oil and computational studies of auto-tractor diesel engine type D-245.12 (1 ChN 11/12,5), working on blends of petroleum diesel fuel and rapeseed oil. When switching autotractor diesel engine from diesel fuel to rapeseed oil in the full-fuel mode, the mass cycle fuel supply increased by 12 %, and in the small-size high-speed diesel engine – by about 27 %. From the point of view of the flow of the working process of these diesel engines, changes in other parameters of the fuel injection process are less significant. Keywords diesel engine; petroleum diesel fuel; vegetable oil; rapeseed oil; high pressure fuel pump; fuel injector; sprayer


2019 ◽  
Vol 179 (4) ◽  
pp. 75-79
Author(s):  
Łukasz GRABOWSKI ◽  
Paweł KARPIŃSKI ◽  
Grzegorz BARAŃSKI

This paper presents the results of experimental studies of the opposed-piston diesel engine. This engine was designed during one of the stages of the research on a new-type drive unit for gyrocopter applications. In order to conduct research, a special test stand as well as control and measurement systems were developed. As part of the work on the engine, the fuel injection system, engine temperature control system and measurement systems were designed. In addition, a computer program has been developed for the fuel injection system control (injectors, valves fuel pressure regulators). The paper presents the results of the preliminary tests for a single value of engine speed (1500 rpm) and three values of load defined by torque. The measured value of the indicated pressure made it possible to calculate the maximum pressure. The results obtained from the bench tests were analyzed.


Author(s):  
Simona Silvia Merola ◽  
Bianca M. Vaglieco ◽  
Silvano Consales ◽  
Felice E. Corcione ◽  
Giuseppe Formisano

Sign in / Sign up

Export Citation Format

Share Document