USE OF NORTHERN ECOTYPE SOYBEANS FOR BIOFUEL PRODUCTION

2020 ◽  
pp. 22-30
Author(s):  
SERGEY N. DEVYANIN ◽  
◽  
VLADIMIR A. MARKOV ◽  
ALEKSANDR G. LEVSHIN ◽  
TAMARA P. KOBOZEVA ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Soybean Oil ◽  
Diesel Fuel ◽  
Experimental Studies ◽  
Motor Fuel ◽  
Biodiesel Production ◽  
Biofuel Production ◽  
Exhaust Gases ◽  
Oil Productivity ◽  
Toxic Components

The paper presents the results of long-term research on the oil productivity and chemical composition of soybean oil of the Northern ecotype varieties in the Central Non-Black Earth Region. The authors consider its possible use for biodiesel production. Experiments on growing soybeans were carried out on the experimental fi eld of Russian State Agrarian University –Moscow Timiryazev Agricultural Academy (2008-2019) on recognized ultra-early ripening varieties of the Northern ecotype Mageva, Svetlaya, Okskaya (ripeness group 000). Tests were set and the research results were analyzed using standard approved methods. It has been shown that in conditions of high latitudes (57°N), limited thermal resources of the Non-Chernozem zone of Russia (the sum of active temperatures of the growing season not exceeding 2000°С), the yield and productivity of soybeans depend on the variety and moisture supply. Over the years, the average yield of soybeans amounted to 1.94 … 2.62 t/ha, oil productivity – 388 … 544 kg/ha, oil content – 19…20%, the content of oleic and linoleic fatty acids in oil – 60%, and their output from seeds harvested – 300 kg/ha. It has been established that as soybean oil and diesel fuel have similar properties,they can be mixed by conventional methods in any proportions and form stable blends that can be stored for a long time. Experimental studies on the use of soybean oil for biodiesel production were carried out on a D-245 diesel engine (4 ChN11/12.5). The concentrations of toxic components (CO, CHx, and NOx) in the diesel exhaust gases were determined using the SAE-7532 gas analyzer. The smoke content of the exhaust gases was measured with an MK-3 Hartridge opacimeter. It has been experimentally established that the transfer of a diesel engine from diesel fuel to a blend of 80% diesel fuel and 20% lubrication oil leads to a change in the integral emissions per test cycle: nitrogen oxides in 0.81 times, carbon monoxide in 0.89 times and unburned hydrocarbons in 0.91 times, i.e. when biodiesel as used as a motor fuel in a serial diesel engine, emissions of all gaseous toxic components are reduced. The study has confi rmed the expediency of using soybeans of the Northern ecotype for biofuel production.

Diesel engine performance at the intake of the hydrogen&air mixture

2021 ◽  
pp. 119-126
Author(s):  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Fuel Efficiency ◽  
Experimental Studies ◽  
Motor Fuel ◽  
Engine Performance ◽  
Calorific Value ◽  
Hydrocarbon Emissions ◽  
The Difference

The prospects of using hydrogen as a motor fuel are noted. The problems that arise when converting a diesel engine to run on hydrogen are considered. The features of the organization of the working process of enginesrunning on hydrogen are analyzed. A method of supplying a hydrogenair mixture to a diesel engine is investigated. To supply hydrogen to the engine cylinders, it is proposed to use the Leader4M installation developed by TechnoHill Club LLC (Moscow). Experimental studies of a stationary diesel engine of the D245.12 S type with the supply of hydrogen at the inlet obtained at this installation are carried out. At the maximum power mode, the supply of hydrogen from this installation to the inlet of the diesel engine under study was 0.9 % by weight (taking into account the difference in the calorific value of oil diesel fuel and hydrogen). Such a supply of hydrogen in the specified mode made it possible to increase the fuel efficiency of the diesel engine and reduce the smoke content of exhaust gases, carbon monoxide and unburned hydrocarbon emissions. Keywords internal combustion engines; diesel engine; diesel fuel; hydrogen; hydrogenair mixture; fuel efficiency; exhaust gas toxicity indicators

scholarly journals EDITORIAL

2007 ◽  
Vol 6 (1) ◽  
pp. 02
Author(s):  
J. V. C. Vargas
Keyword(s):  
Diesel Fuel ◽  
Sugar Cane ◽  
Alternative Fuels ◽  
Fossil Fuels ◽  
Biodiesel Production ◽  
Biofuel Production ◽  
Global Demand ◽  
Oil Productivity ◽  
Carbon Neutral ◽  
Near Future

Fossil fuels are currently recognized as unsustainable because of depleting supplies and the contribution of these fuels to the accumulation of carbon dioxide in the environment. Therefore, renewable, carbon neutral, alternative fuels are necessary for environmental and economic sustainability. Several countries have been considering the use of alternative fuels derived from agriculture. In that context, ethanol derived from sugar-cane and/or corn crops, and biodiesel derived from oil crops are potential renewable and carbon neutral alternatives to fossil fuels. Unfortunately, fuel from crops, waste and animal fat cannot realistically satisfy even a small fraction of the existing global demand for fuels. In Brazil, the government has been subsiding ethanol from sugar-cane crops for more than 30 years, and together with research investment on oil off-shore exploration, the initiative made possible for the country, at least for the moment, to become energy self sufficient, but due to oil supplies depletion, that scenery will change in the near future. Another limiting factor is cost. For example, the economic aspect of biodiesel production limits its development and large-scale use. Biodiesel usually costs almost twice the price per liter of conventional diesel fuel, currently in the US.Apart from economic aspects, it is clear that biofuel production technology needs to be improved to meet global fuel demand rate. One possible direction is the use of microalgae, that appear to be the only source of renewable biodiesel that is capable of meeting the diesel fuel global demand. Like plants, microalgae use sunlight to produce oils but they do so more efficiently than crop plants. Oil productivity of many microalgae greatly exceeds the oil productivity of the best producing oil crops.Approaches for making microalgal biodiesel economically competitive therefore need to be developed.The mission of Engenharia Térmica is to document the scientific progress in areas related to energy, particularly oil and renewables. We are confident we will continue to receive articles’ submissions that help enable sustainable energy solutions in the near future.

scholarly journals Effect of biodiesel on diesel engine emissions

2018 ◽  
Vol 22 (Suppl. 5) ◽  
pp. 1483-1498 ◽  
Author(s):  
Boban Nikolic ◽  
Breda Kegl ◽  
Sasa Milanovic ◽  
Milos Jovanovic ◽  
Zivan Spasic
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Raw Materials ◽  
Relevant Literature ◽  
Biodiesel Production ◽  
Engine Fuel ◽  
Engine Emissions ◽  
Exhaust Gases ◽  
Physical And Chemical

Extensive research has been carried out with regard to the composition of the exhaust gases of Diesel engines in operation with biodiesel in relation to the operation with the conventional diesel fuel. Producing biodiesel from different raw materials and different technological biodiesel production processes can result in different individual physical and chemical characteristics of fuel. Generally, it can be said that the use of biodiesel (and mixtures) reduces the overall toxicity of the exhaust gases in relation to the operation of the engine with diesel fuel, and this is a significant environmental potential of biodiesel as a fuel for Diesel engines. However, there is a diversity of research results, due to different factors. The paper reviews and summarizes the relevant literature on the mentioned research that can contribute to the explanation of these effects. It also points to the need for a very careful selection of biodiesel for use as a Diesel engine fuel.

Investigation of the Possibilities of Using Soybean Oil as an Ecological Additive to Petroleum Diesel Fuel

2022 ◽  
pp. 39-52
Author(s):  
S.N. Devyanin ◽  
V.A. Markov ◽  
A.G. Levshin ◽  
T.P. Kobozeva ◽  
V.A. Neverov
Keyword(s):  
Diesel Engine ◽  
Soybean Oil ◽  
Diesel Fuel ◽  
Alternative Fuels ◽  
Combustion Engine ◽  
Raw Materials ◽  
Experimental Studies ◽  
Chemical Properties ◽  
Promising Alternative ◽  
Plant Raw Materials

One of the most important areas of internal combustion engine improvement is its adaptation to work on alternative fuels. Motor fuels obtained from renewable plant raw materials are considered to be promising alternative fuels. The article considers the possibility of using soybean oil as an ecological additive in petroleum diesel fuel. The features of soybean oil production and the physico-chemical properties of soybean oil and a mixture containing 80 % (by volume) of petroleum diesel fuel and 20 % of soybean oil are researched. Computational studies of the processes of fuel atomization and mixture formation in the D-245 diesel engine operating on mixtures of petroleum diesel fuel and seed oil have been performed. Experimental studies of the D-245 diesel engine operating on petroleum diesel fuel and the specified blended fuel have been carried out. Conversion of a diesel engine from petroleum fuel to mixed one leads to a decrease in integral emissions per test cycle: nitrogen oxides by 19.1 %, carbon monoxide — by 10.5 %, unburned hydrocarbons - by 8.9 %.

Decrease in Toxicity of Vehicle Exhaust Gases of Car Diesel by Conversion to Alcohol-Fuel Emulsions

2018 ◽  
Vol 22 (10) ◽  
pp. 54-59 ◽  
Author(s):  
V.A. Likhanov ◽  
O.P. Lopatin
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Experimental Studies ◽  
Diesel Oil ◽  
Vehicle Exhaust ◽  
Ethanol Fuel ◽  
Exhaust Gases ◽  
Alcohol Fuel ◽  
Dispersant Additive ◽  
Carbon Dioxide Co2

The results of the studies of reducing the toxicity of vehicle exhaust gases of car diesel by conversion to alcohol-fuel emulsions are presented. At the same time, the necessity of applying alcohol-fuel emulsions as an environmentally friendly fuel is grounded. In order to develop, determine and optimize the composition of alcohol-fuel emulsions, their tests were carried out when the diesel engine is operated with diesel fuel, methanol and ethanol-fuel emulsions. Experimental studies have established that in car diesel engine 4 Ч 11,0/12,5, emulsions with the following composition may be optimal for use, %: alcohol (methanol or ethanol) – 25, detergent-dispersant additive succinimides C-5A -0.5, water – 7, diesel fuel – 67.5. Conversion of car diesel from diesel oil to methanol-fuel emulsion reduces the content of carbon black (C) in exhaust gases by 6.9 times, nitrogen oxides (NOx) by 41.3 %, carbon dioxide (CO2) by 6.7 %, oxide carbon (CO) by 45.0 %; on the ethanol-fuel emulsion – C in 5.2 times, NOx by 50.2 %, CO2 by 23.8 %, CO by 25.0 %.

DIESEL ENGINE OPERATION IN USE OF FUEL WITH ADDITIVES

2018 ◽  
pp. 18-24
Author(s):  
Petar Kazakov ◽  
Atanas Iliev ◽  
Emil Marinov
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Internal Combustion Engines ◽  
Experimental Studies ◽  
Combustion Engines ◽  
Engine Operation ◽  
Factors Affecting ◽  
Operating Modes ◽  
Positive Effects

Over the decades, more attention has been paid to emissions from the means of transport and the use of different fuels and combustion fuels for the operation of internal combustion engines than on fuel consumption. This, in turn, enables research into products that are said to reduce fuel consumption. The report summarizes four studies of fuel-related innovation products. The studies covered by this report are conducted with diesel fuel and usually contain diesel fuel and three additives for it. Manufacturers of additives are based on already existing studies showing a 10-30% reduction in fuel consumption. Comparative experimental studies related to the use of commercially available diesel fuel with and without the use of additives have been performed in laboratory conditions. The studies were carried out on a stationary diesel engine СМД-17КН equipped with brake КИ1368В. Repeated results were recorded, but they did not confirm the significant positive effect of additives on specific fuel consumption. In some cases, the factors affecting errors in this type of research on the effectiveness of fuel additives for commercial purposes are considered. The reasons for the positive effects of such use of additives in certain engine operating modes are also clarified.

OPTIMIZATION OF GAS-DIESEL ENGINE REGULATION AS A METHOD OF IMPROVING ITS ECOLOGICAL CHARACTERISTICS

2021 ◽  
pp. 28-32
Author(s):  
VALERIY L. CHUMAKOV ◽  
Keyword(s):  
Carbon Monoxide ◽  
Diesel Engine ◽  
Nitrogen Oxides ◽  
Diesel Fuel ◽  
Hydrocarbon Fuel ◽  
Load Range ◽  
Engine Operation ◽  
Exhaust Gases ◽  
Wide Range ◽  
Diesel Cycle

The paper shows some ways to improve the environmental characteristics of a diesel engine using gaseous hydrocarbon fuel and operating the engine in a gas-diesel cycle mode. Some possibilities to reduce toxic components of exhaust gases in a gas-diesel engine operating on liquefi ed propane-butane mixtures have been studied. Experiments carried out in a wide range of load from 10 to 100% and speed from 1400 to 2000 rpm showed that the gas-diesel engine provides a suffi ciently high level of diesel fuel replacement with gas hydrocarbon fuel. The authors indicate some eff ective ways to reduce the toxicity of exhaust gases. The engine power should be adjusted by the simultaneous supply of fuel, gas and throttling the air charge in the intake manifold. This method enriches the fi rst combusting portions to reduce nitrogen oxides and maintains the depletion of the main charge within the fl ammability limits of the gas-air charge to reduce carbon monoxide and hydrocarbons. The authors found that when the engine operates in a gas-diesel cycle mode, the power change provides a decrease in nitrogen oxide emissions of gas-diesel fuel only due to gas supply in almost the entire load range as compared to the pure diesel. At high loads (more than 80%) stable engine operation is ensured up to 90% of diesel fuel replaced by gas. Even at 10% of diesel fuel used the concentration of nitrogen oxides decreases by at least 15…20% as compared with a diesel engine in the entire load range. However, there is an increased emission of hydrocarbons and carbon monoxide in the exhaust gases. Further experimental studies have shown that optimization of the gas diesel regulation can reduce the mass emission of nitrogen oxides contained in exhaust gases in 2…3 times and greatly reduce the emission of incomplete combustion products – carbon monoxide and hydrocarbons.

Characteristics of injection of diesel fuel, rapeseed oil and their mixtures in diesel engines of various types

2021 ◽  
pp. 167-178
Author(s):  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Rapeseed Oil ◽  
High Speed ◽  
Fuel Injection ◽  
Experimental Studies ◽  
Fuel Injector ◽  
High Speed Diesel ◽  
Engine Type

The necessity of adapting diesel engines to work on vegetable oils is justified. The possibility of using rapeseed oil and its mixtures with petroleum diesel fuel as motor fuels is considered. Experimental studies of fuel injection of small high-speed diesel engine type MD-6 (1 Ch 8,0/7,5)when using diesel oil and rapeseed oil and computational studies of auto-tractor diesel engine type D-245.12 (1 ChN 11/12,5), working on blends of petroleum diesel fuel and rapeseed oil. When switching autotractor diesel engine from diesel fuel to rapeseed oil in the full-fuel mode, the mass cycle fuel supply increased by 12 %, and in the small-size high-speed diesel engine – by about 27 %. From the point of view of the flow of the working process of these diesel engines, changes in other parameters of the fuel injection process are less significant. Keywords diesel engine; petroleum diesel fuel; vegetable oil; rapeseed oil; high pressure fuel pump; fuel injector; sprayer

Experimental Studies on the Performance of C.I Engine with Fish Oil Methyl Ester as Fuel for Various Blends of Diesel and LPG

2015 ◽  
Vol 787 ◽  
pp. 687-691
Author(s):  
Tarigonda Hari Prasad ◽  
R. Meenakshi Reddy ◽  
P. Mallikarjuna Rao
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Alternative Fuels ◽  
Internal Combustion Engines ◽  
Fossil Fuels ◽  
Research Work ◽  
Experimental Studies ◽  
Internal Combustion ◽  
Combustion Engines ◽  
Inlet Manifold

Fossil fuels are exhausting quickly because of incremental utilization rate due to increase population and essential comforts on par with civilization. In this connection, the conventional fuels especially petrol and diesel for internal combustion engines, are getting exhausted at an alarming rate. In order to plan for survival of technology in future it is necessary to plan for alternate fuels. Further, these fossil fuels cause serious environmental problems as they release toxic gases into the atmosphere at high temperatures and concentrations. The predicted global energy consumption is increasing at faster rate. In view of this and many other related issues, these fuels will have to be replaced completely or partially by less harmful alternative, eco-friendly and renewable source fuels for the internal combustion engines. Hence, throughout the world, lot of research work is in progress pertaining to suitability and feasibility of alternative fuels. Biodiesel is one of the promising sources of energy to mitigate both the serious problems of the society viz., depletion of fossil fuels and environmental pollution. In the present work, experiments are carried out on a Single cylinder diesel engine which is commonly used in agricultural sector. Experiments are conducted by fuelling the diesel engine with bio-diesel with LPG through inlet manifold. The engine is properly modified to operate under dual fuel operation using LPG through inlet manifold as fuel along FME as ignition source. The brake thermal efficiency of FME with LPG (2LPM) blend is increased at an average of 5% when compared to the pure diesel fuel. HC emissions of FME with LPG (2LPM) blend are reduced by about at an average of 21% when compared to the pure diesel fuel. CO emissions of FME with LPG (2LPM) blends are reduced at an average of 33.6% when compared to the pure diesel fuel. NOx emissions of FME with LPG (2LPM) blend are reduced at an average of 4.4% when compared to the pure diesel fuel. Smoke opacity of FME with LPG (2LPM) blend is reduced at an average of 10% when compared to the pure diesel fuel.

scholarly journals Influence of Variable Speed on Performance and Emission Characteristics of Diesel Engine using Fish Oil Biodiesel Blends

2020 ◽  
Vol 8 (5) ◽  
pp. 3950-3954
Keyword(s):  
Diesel Engine ◽  
Fish Oil ◽  
Diesel Fuel ◽  
Fossil Fuels ◽  
Direct Injection ◽  
Petroleum Products ◽  
Point Of View ◽  
Biodiesel Production ◽  
Biodiesel Fuel ◽  
Performance And Emission

Alternative fuel sources are needed to be developed to meet the escalating demand for fossil fuels. Also from an environmental point of view, these most modern resources of fuels must be environment-friendly. The rapidly increasing consumption of fossil fuel and petroleum products has been a matter of concern for many countries which imports more crude oil. So, there is necessary for the development of new energy sources. The biomass, edible oil, inedible oils from plants and fish fat oil are imperatives and seen to be a potential substitute for diesel fuel. Acid and Base catalyzed transesterification is the most acceptable process for biodiesel production. In this project, an attempt towards finding the effect of alternate fuels as a substitute over diesel and reduce its consumption to lessen the environmental effects. Biodiesel has been extensively used in diesel engines as a partial substitute in the past few decades. The present investigation is carried out with blending up fish oil biodiesel with diesel in varying proportions to test out the emission and performance characteristics of direct injection single cylinder, four strokes, and air-cooled diesel engine. The fish oil biodiesel was produced by the transesterification process and obtained fish oil biodiesel blended with diesel fuel with various propagations of B20, B50, B75 & B100. These blended fuels were further investigated in a diesel engine with variable speeds such as 1000rpm, 1250rpm, 1500rpm, 1720rpm, 2000rpm 2250rpm & 2500rpm. In this comparative study, the effects of fish oil biodiesel fuel blends are compared and evaluated with pure diesel.

Sign in / Sign up

Export Citation Format

Share Document