Study on aramid short fiber reinforced CFRP/aluminum layered structure and its galvanic corrosion resistance

2022 ◽  
pp. 1-17
Author(s):  
Binhua Wang ◽  
Xuanheng Fang ◽  
Yubo Xue
Keyword(s):  
Corrosion Resistance ◽  
Layered Structure ◽  
Galvanic Corrosion ◽  
Short Fiber ◽  
Fiber Reinforced

scholarly journals Tensile Property, Corrosion Resistance and Cytocompatibility of Tungsten Short Fiber Reinforced Ti-6Al-4V Alloy

2002 ◽  
Vol 43 (12) ◽  
pp. 2995-2999
Author(s):  
Masaaki Koganemaru ◽  
Yoshimitsu Okazaki ◽  
Emiko Nishimura ◽  
Shinichi Nishida ◽  
Kouichi Nakano ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Tensile Property ◽  
Short Fiber ◽  
Fiber Reinforced

Heat Treatment Influence on the Corrosion Resistance of a Cu-Al-Fe-Mn Bronze

2018 ◽  
Vol 69 (5) ◽  
pp. 1055-1059 ◽  
Author(s):  
Mariana Ciurdas ◽  
Ioana Arina Gherghescu ◽  
Sorin Ciuca ◽  
Alina Daniela Necsulescu ◽  
Cosmin Cotrut ◽  
...  
Keyword(s):  
Heat Treatment ◽  
Corrosion Resistance ◽  
Structural Changes ◽  
Heating Temperature ◽  
Galvanic Corrosion ◽  
Cooling Water ◽  
Open Circuit ◽  
Water Quenching ◽  
Heat Treated ◽  
Different Temperatures

Aluminium bronzes are exhibiting good corrosion resistance in saline environments combined with high mechanical properties. Their corrosion resistance is obviously confered by the alloy chemical composition, but it can also be improved by heat treatment structural changes. In the present paper, five Cu-Al-Fe-Mn bronze samples were subjected to annealing heat treatments with furnace cooling, water quenching and water quenching followed by tempering at three different temperatures: 200, 400 and 550�C. The heating temperature on annealing and quenching was 900�C. The structure of the heat treated samples was studied by optical and scanning electron microscopy. Subsequently, the five samples were submitted to corrosion tests. The best resistance to galvanic corrosion was showed by the quenched sample, but it can be said that all samples are characterized by close values of open-circuit potentials and corrosion potentials. Concerning the susceptibility to other types of corrosion (selective leaching, pitting, crevice corrosion), the best corrosion resistant structure consists of a solid solution, g2 and k compounds, corresponding to the quenched and 550�C tempered sample.

scholarly journals Corrosion Behavior and Galvanic Corrosion Resistance of WC and Cr3C2 Cermet Coatings in Madeira River Water

2021 ◽  
Author(s):  
Leonardo Augusto Luiz ◽  
Juliano de Andrade ◽  
Camila Melo Pesqueira ◽  
Irene Bida de Araújo Fernandes Siqueira ◽  
Gustavo Bavaresco Sucharski ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
River Water ◽  
Corrosion Behavior ◽  
Galvanic Corrosion ◽  
Cermet Coatings ◽  
Madeira River

scholarly journals Effect of Short Fiber Reinforcements on Fracture Performance of Cement-Based Materials: A Systematic Review Approach

Materials ◽  
2021 ◽  
Vol 14 (7) ◽  
pp. 1745
Author(s):  
Waqas Ahmad ◽  
Mehran Khan ◽  
Piotr Smarzewski
Keyword(s):  
Graphical Representation ◽  
Safety Evaluation ◽  
Short Fiber ◽  
Research Trend ◽  
Scientometric Analysis ◽  
Fiber Reinforced ◽  
Factors Affecting ◽  
Fracture Properties ◽  
Cement Based Materials ◽  
Relevant Publication

Fracture characteristics were used to effectively evaluate the performance of fiber-reinforced cementitious composites. The fracture parameters provided the basis for crack stability analysis, service performance, safety evaluation, and protection. Much research has been carried out in the proposed study field over the previous two decades. Therefore, it was required to analyze the research trend from the available bibliometric data. In this study, the scientometric analysis and science mapping techniques were performed along with a comprehensive discussion to identify the relevant publication field, highly used keywords, most active authors, most cited articles, and regions with largest impact on the field of fracture properties of cement-based materials (CBMs). Furthermore, the characteristic of various fibers such as steel, polymeric, inorganic, and carbon fibers are discussed, and the factors affecting the fracture properties of fiber-reinforced CBMs (FRCBMs) are reviewed. In addition, future gaps are identified. The graphical representation based on the scientometric review could be helpful for research scholars from different countries in developing research cooperation, creating joint ventures, and exchanging innovative technologies and ideas.

scholarly journals A computational modeling approach based on random fields for short fiber-reinforced composites with experimental verification by nanoindentation and tensile tests

2021 ◽  
Author(s):  
Natalie Rauter
Keyword(s):  
Numerical Simulations ◽  
Correlation Functions ◽  
Material Properties ◽  
Random Fields ◽  
Tensile Tests ◽  
Short Fiber ◽  
Fiber Reinforced Composites ◽  
Reinforced Composites ◽  
Fiber Reinforced ◽  
Component Level

AbstractIn this study a modeling approach for short fiber-reinforced composites is presented which allows one to consider information from the microstructure of the compound while modeling on the component level. The proposed technique is based on the determination of correlation functions by the moving window method. Using these correlation functions random fields are generated by the Karhunen–Loève expansion. Linear elastic numerical simulations are conducted on the mesoscale and component level based on the probabilistic characteristics of the microstructure derived from a two-dimensional micrograph. The experimental validation by nanoindentation on the mesoscale shows good conformity with the numerical simulations. For the numerical modeling on the component level the comparison of experimentally obtained Young’s modulus by tensile tests with numerical simulations indicate that the presented approach requires three-dimensional information of the probabilistic characteristics of the microstructure. Using this information not only the overall material properties are approximated sufficiently, but also the local distribution of the material properties shows the same trend as the results of conducted tensile tests.

Data enriched lubrication force modeling for a mechanistic fiber simulation of short fiber-reinforced thermoplastics

2021 ◽  
Vol 33 (5) ◽  
pp. 053107
Author(s):  
Susanne K. Kugler ◽  
Abrahán Bechara ◽  
Hector Perez ◽  
Camilo Cruz ◽  
Armin Kech ◽  
...  
Keyword(s):  
Short Fiber ◽  
Fiber Reinforced ◽  
Force Modeling ◽  
Reinforced Thermoplastics ◽  
Fiber Reinforced Thermoplastics

scholarly journals Pitting Corrosion Resistance and Repassivation Behavior of C-Bearing Duplex Stainless Steel

Metals ◽  
2019 ◽  
Vol 9 (9) ◽  
pp. 930 ◽  
Author(s):  
Hanme Yoon ◽  
Heon-Young Ha ◽  
Tae-Ho Lee ◽  
Sung-Dae Kim ◽  
Jae Hoon Jang ◽  
...  
Keyword(s):  
Corrosion Resistance ◽  
Pitting Corrosion ◽  
Galvanic Corrosion ◽  
Dual Phase ◽  
Corrosion Resistant ◽  
Grain Sizes ◽  
Α Phase ◽  
Pitting Corrosion Resistance ◽  
Corrosion Pits ◽  
Pit Initiation

The effects of C-substitution for part of the N content, on the pitting corrosion resistance and repassivation tendencies of duplex stainless steels (DSSs) were investigated. For this investigation, normal UNS S32205 containing N only (DSS-N) and the C-substituted DSS (DSS-NC) were fabricated. Microstructural analyses confirmed that the two DSSs had dual-phase microstructures without precipitates, and they possessed similar initial microstructure, including their grain sizes and phase fractions. Polarization and immersion tests performed in concentrated chloride solutions revealed that the DSS-NC was more resistant against stable pitting corrosion and possessed a higher repassivation tendency than the DSS-N. Furthermore, the corrosion pits initiated and propagated to a less corrosion resistant α phase. Polarization tests and corrosion depth measurements conducted in an HCl solution indicated that the DSS-NC exhibited lower galvanic corrosion rate between the α and γ phases than the DSS-N. Therefore, the growth rate of pit embryo was lowered in the DSS-NC, which shifted the potentials for the stable pit initiation and the pit extinction to the higher values.

Anisotropic Effective Moduli of Cracked Short-Fiber Reinforced Composites

1999 ◽  
Vol 66 (3) ◽  
pp. 709-713 ◽  
Author(s):  
R. S. Feltman ◽  
M. H. Santare
Keyword(s):  
Short Fiber ◽  
Fiber Reinforced Composites ◽  
Reinforced Composites ◽  
Effective Moduli ◽  
Fiber Reinforced ◽  
Fiber Fracture ◽  
Composite Systems ◽  
Reinforced Composite ◽  
Anisotropic Elastic ◽  
Energy Dissipated

A model is presented to analyze the effect of fiber fracture on the anisotropic elastic properties of short-fiber reinforced composite materials. The effective moduli of the material are modeled using a self-consistent scheme which includes the calculated energy dissipated through the opening of a crack in an arbitrarily oriented elliptical inclusion. The model is an extension of previous works which have modeled isotropic properties of short-fiber reinforced composites with fiber breakage and anisotropic properties of monolithic materials with microcracks. Two-dimensional planar composite systems are considered. The model allows for the calculation of moduli under varying degrees of fiber alignment and damage orientation. In the results, both aligned fiber systems and randomly oriented fiber systems with damage-induced anisotropy are examined.

Sign in / Sign up

Export Citation Format

Share Document