scholarly journals Measuerment of CO2-crude oil minimum miscible pressure in YC Oilfield by core displacement method

2021 ◽  
Vol 2109 (1) ◽  
pp. 012006
Author(s):  
Li Liu ◽  
Jinxin Liu ◽  
Yanfu Pi ◽  
Xuan Guo ◽  
Zhipeng Dai ◽  
...  
Keyword(s):  
Crude Oil ◽  
Physical Simulation ◽  
Low Permeability ◽  
Displacement Method ◽  
Reservoir Water ◽  
Tube Test ◽  
Reservoir Conditions ◽  
Good Repeatability ◽  
Target Block ◽  
Core Displacement

Abstract Aiming at the defect of measuring the CO2-crude oil MMP(minimum miscible pressure) by the slim tube test, the core displacement method is established based on indoor physical simulation and homogeneous rectangular core in the low permeability block of YC oilfield. For comparison, the MMP is measured by the slim tube test in the same block. Experimental results show that the method has good repeatability and can simulate porous media and reservoir water content, which is more consistent with the actual reservoir conditions. The MMP in the target block of YC oilfield was 19.85MPa, which was 1.87MPa lower than that measured by traditional slim tube test.

scholarly journals Comparative Analysis of CO2, N2, and Gas Mixture Injection on Asphaltene Deposition Pressure in Reservoir Conditions

Energies ◽  
2018 ◽  
Vol 11 (9) ◽  
pp. 2483 ◽  
Author(s):  
Peng Wang ◽  
Fenglan Zhao ◽  
Jirui Hou ◽  
Guoyong Lu ◽  
Meng Zhang ◽  
...  
Keyword(s):  
Crude Oil ◽  
Pressure Range ◽  
Co2 Injection ◽  
Gas Mixture ◽  
Low Permeability ◽  
Deposition Pressure ◽  
Severe Problem ◽  
Asphaltene Deposition ◽  
Reservoir Conditions ◽  
Buried Hill

CO2 and N2 injection is an effective enhanced oil recovery technology in the oilfield especially for low-permeability and extra low-permeability reservoirs. However, these processes can induce an asphaltene deposition during oil production. Asphaltene-deposition-induced formation damage is a fairly severe problem. Therefore, predicting the likelihood of asphaltene deposition in reservoir conditions is crucial. This paper presents the results of flash separation experiments used to investigate the composition of crude oil in shallow and buried-hill reservoirs. Then, PVTsim Nova is used to simulate the composition change and asphaltene deposition of crude oil. Simulation tests indicate that the content of light components C1-C4 and heavy components C36+ decrease with increasing CO2 and N2 injection volumes. However, the extraction of CO2 is significantly stronger than that of N2. In shallow reservoirs, as the CO2 injection volume increases, the deposition pressure range decreases and asphaltenes are easily deposited. Conversely, the asphaltene deposition pressure of crude oil injected with N2 is higher and will not cause serious asphaltene deposition. When the CO2-N2 injection ratio reaches 1:1, the deposition pressure range shows a significant transition. In buried-hill reservoirs, asphaltene deposition is unlikely to occur with CO2, N2, and a gas mixture injection.

scholarly journals CO2 Convective Dissolution in Oil-Saturated Unconsolidated Porous Media at Reservoir Conditions

Energies ◽  
2021 ◽  
Vol 14 (1) ◽  
pp. 233
Author(s):  
Widuramina Amarasinghe ◽  
Ingebret Fjelde ◽  
Nils Giske ◽  
Ying Guo
Keyword(s):  
Porous Media ◽  
Crude Oil ◽  
Water Solution ◽  
Co2 Storage ◽  
Bromothymol Blue ◽  
Power Relationship ◽  
Dimensionless Time ◽  
3 Dimensional ◽  
Reservoir Conditions ◽  
Unconsolidated Porous Media

During CO2 storage, CO2 plume mixes with the water and oil present at the reservoir, initiated by diffusion followed by a density gradient that leads to a convective flow. Studies are available where CO2 convective mixing have been studied in water phase but limited in oil phase. This study was conducted to reach this gap, and experiments were conducted in a vertically packed 3-dimensional column with oil-saturated unconsolidated porous media at 100 bar and 50 °C (representative of reservoir pressure and temperature conditions). N-Decane and crude oil were used as oils, and glass beads as porous media. A bromothymol blue water solution-filled sapphire cell connected at the bottom of the column was used to monitor the CO2 breakthrough. With the increase of the Rayleigh number, the CO2 transport rate in n-decane was found to increase as a function of a second order polynomial. Ra number vs. dimensionless time τ had a power relationship in the form of Ra = c×τ−n. The overall pressure decay was faster in n-decane compared to crude oil for similar permeability (4 D), and the crude oil had a breakthrough time three times slower than in n-decane. The results were compared with similar experiments that have been carried out using water.

Advance Water-Flooding to Reduce the Stress Sensitivity Affect on Low Permeability Reservoir Development

2011 ◽  
Vol 361-363 ◽  
pp. 520-525
Author(s):  
Jun Feng Yang ◽  
Han Qiao Jiang ◽  
Han Dong Rui ◽  
Xiao Qing Xie
Keyword(s):  
Physical Simulation ◽  
Physical Property ◽  
Stress Sensitivity ◽  
Water Flooding ◽  
Low Permeability ◽  
Formation Pressure ◽  
Exponential Relationship ◽  
Low Permeability Reservoir ◽  
Reservoir Development ◽  
Water Cut

Physical simulation experiments were made to research on the stress sensitivity on physical property of low permeability reservoir rocks. The experimental results shown that effective pressure had good exponential relationship with reservoir permeability. Combining with materaial balance method, reservoir engineering and rational deducation was made to reserach on water-flooding timing of low permeability reservoir development. Several production targets were obtained by these method, such as formation pressure, water and oil production, water cut and so on. The results shown that advanced water-flooding was very important in low permeability reservoir development to reduce the bad impact of stress sensitivity on formation permeability and maintain formation pressure.

Injectivity and Propagation of Sulfonated Acrylamide-Based Copolymers in Low Permeability Carbonate Reservoir Cores in Harsh Salinity and Temperature Conditions : Challenges and Learnings from a Middle East Onshore Case Study

2021 ◽  
Author(s):  
Nicolas Gaillard ◽  
Matthieu Olivaud ◽  
Alain Zaitoun ◽  
Mahmoud Ould-Metidji ◽  
Guillaume Dupuis ◽  
...  
Keyword(s):  
Middle East ◽  
Polymer Solutions ◽  
Carbonate Reservoir ◽  
Core Material ◽  
Low Permeability ◽  
The Core ◽  
Reservoir Conditions ◽  
Carbonate Cores ◽  
The Impact ◽  
Mobility Reduction

Abstract Polymer flooding is one of the most mature EOR technology applied successfully in a broad range of reservoir conditions. The last developments made in polymer chemistries allowed pushing the boundaries of applicability towards higher temperature and salinity carbonate reservoirs. Specifically designed sulfonated acrylamide-based copolymers (SPAM) have been proven to be stable for more than one year at 120°C and are the best candidates to comply with Middle East carbonate reservoir conditions. Numerous studies have shown good injectivity and propagation properties of SPAM in carbonate cores with permeabilities ranging from 70 to 150 mD in presence of oil. This study aims at providing new insights on the propagation of SPAM in carbonate reservoir cores having permeabilities ranging between 10 and 40 mD. Polymer screening was performed in the conditions of ADNOC onshore carbonate reservoir using a 260 g/L TDS synthetic formation brine together with oil and core material from the reservoir. All the experiments were performed at residual oil saturation (Sor). The experimental approach aimed at reproducing the transport of the polymer entering the reservoir from the sand face up to a certain depth. Three reservoir coreflood experiments were performed in series at increasing temperatures and decreasing rates to mimic the progression of the polymer in the reservoir with a radial velocity profile. A polymer solution at 2000 ppm was injected in the first core at 100 mL/h and 40°C. Effluents were collected and injected in the second core at 20 mL/h and 70°C. Effluents were collected again and injected in the third core at 4 mL/h and 120°C. A further innovative approach using reservoir minicores (6 mm length disks) was also implemented to screen the impact of different parameters such as Sor, molecular weight and prefiltration step on the injectivity of the polymer solutions. According to minicores data, shearing of the polymer should help to ensure good propagation and avoid pressure build-up at the core inlet. This result was confirmed through an injection in a larger core at Sor and at 120°C. When comparing the injection of sheared and unsheared polymer at the same concentration, core inlet impairment was suppressed with the sheared polymer and the same range of mobility reduction (Rm) was achieved in the internal section of the core although viscosity was lower for the sheared polymer. Such result indicates that shearing is an efficient way to improve injectivity while maximizing the mobility reduction by suppressing the loss of product by filtration/retention at the core inlet. This paper gives new insights concerning SPAM rheology in low permeability carbonate cores. Additionally, it provides an innovative and easier approach for screening polymer solutions to anticipate their propagation in more advanced coreflooding experiments.

Sign in / Sign up

Export Citation Format

Share Document