scholarly journals Field experiment on flow stabilization of working fluid in a top-heat-type thermosyphon

2021 ◽  
Vol 897 (1) ◽  
pp. 012007
Author(s):  
K Maruyama ◽  
T Kawaguchi ◽  
T Fujisawa ◽  
T Kawashima
Keyword(s):  
Solar Energy ◽  
Field Experiments ◽  
Hot Water ◽  
Working Fluid ◽  
Intermittent Flow ◽  
Damage And Failure ◽  
Flow Stabilization ◽  
External Power Source ◽  
Water Field ◽  
Effective Use

Abstract To address the problem of global warming, increasing efforts are being made to use renewable sources of energy, such as solar energy, wind energy, and geothermal energy. However, the effective use remains a major challenge for its sustainable development. In this study, we used a top-heat-type thermosyphon to heat water using solar energy and transport the low-density hot water from the source to the sink (high to low elevation) without an external power source. The transported hot water can be used for cooking, bathing, underfloor heating, and heating homes and buildings, and warming cold springs. However, a disadvantage of top-heat-type thermosyphon is the intermittent flow of the circulating working fluid under low solar radiation. To address this issue, the authors proposed and developed a control system to stabilize the intermittent flow and prevent equipment damage and failure due to the sudden boiling of water. Field experiments were conducted to assess the practicability of the developed controller. The results showed that the controller efficiently converted the intermittent flow of working fluid to continuous flow by reducing the pressure in the buffer chamber and thus lowering the boiling point of the working fluid in the header of the solar collector.

scholarly journals Investigation of Performance of Solar Flat and Curved Plate Collectors through Numerical Simulations

2021 ◽  
Vol 40 (1) ◽  
pp. 66-74
Author(s):  
Luqman Ahmed Pirzada ◽  
Xiaoli Wu . ◽  
Qaiser Ali ◽  
Asif Khateeb .
Keyword(s):  
Solar Energy ◽  
Flat Plate ◽  
Solar Collector ◽  
Numerical Study ◽  
Hot Water ◽  
Working Fluid ◽  
Solar Panels ◽  
Modeling Tools ◽  
Design Work ◽  
Flat Plate Collector

Solar energy is radiant light as a form of thermal heat energy which can be obtained and used by means of a variety of solar apparatus. As apparatus the flat and curved plate solar collector is specifically designed for assembling solar energy as a solar water heater system. The designing potency of this collector lone can generate medium level hot water from radiant sunlight source via absorbed plates. Standard type flat and curved plates solar collector plates are mostly used in remote coldest regions of the world where hot water is consumed for commercial and domestic purposes. These types of solar collector Plates can cheaply be manufactured compared to other solar panels like solar Shingles, Polycrystalline Solar Panels, Mono-crystalline Solar Panels, and Thin Film Solar Panels. For future work, this proposed pre-design is recommended for fabrication. A numerical study was carried-out on eight city locations in China by tracing their horizontal and vertical longitudinal, latitudinal lines noting the date, time and sunlight feeding of temperatures in the Celsius scale with the help of simulation and modeling tools like CFD, ANSYS FLUENT software, mesh geometry tools, and by using the Navier-Stokes and Continuity equations by fluid flow discharge rate, mass flow, water temperature and dropping of temperature, radiation working mechanisms, dimensions of water flowing tubes and absorber plates, density, the velocity of water as the working fluid, the viscosity of water in a cold and hot state as a process of Pre-design. Work also focuses on the comparison between flat plate collector and curved plate collector radiant sunlight absorption, As end result it is found the Curved plate collector produces 22% more elevated heat of outgoing water than flat plate collector.

Sustainable Cooling with Hybrid Concentrated Photovoltaic Thermal (CPVT) System and Hydrogen Energy Storage

2018 ◽  
Vol 1 (2) ◽  
pp. 40-51 ◽  
Author(s):  
Muhammad Burhan ◽  
Muhammad Wakil Shahzad ◽  
Kim Choon Ng
Keyword(s):  
Energy Storage ◽  
Solar Energy ◽  
Optimization Algorithm ◽  
Concentration Ratio ◽  
Cooling System ◽  
Renewable Energy Sources ◽  
Hot Water ◽  
Hydrogen Energy ◽  
Adsorption Chiller ◽  
Back Plate

Standalone power systems have vital importance as energy source for remote area. On the other hand, a significant portion of such power production is used for cooling purposes. In this scenario, renewable energy sources provide sustainable solution, especially solar energy due to its global availability. Concentrated photovoltaic (CPV) system provides highest efficiency photovoltaic technology, which can operate at x1000 concentration ratio. However, such high concentration ratio requires heat dissipation from the cell area to maintain optimum temperature. This paper discusses the size optimization algorithm of sustainable cooling system using CPVT. Based upon the CPV which is operating at x1000 concentration with back plate liquid cooling, the CPVT system size is optimized to drive a hybrid mechanical vapor compression (MVC) chiller and adsorption chiller, by utilizing both electricity and heat obtained from the solar system. The electrolysis based hydrogen is used as primary energy storage system along with the hot water storage tanks. The micro genetic algorithm (micro-GA) based optimization algorithm is developed to find the optimum size of each component of CPVT-Cooling system with uninterrupted power supply and minimum cost, according to the developed operational strategy. The hybrid system is operated with solar energy system efficiency of 71%.

Development of an Innovative Code for the Design of Different Parabolic Trough Solar Fields

2009 ◽  
Author(s):  
Ennio Macchi ◽  
Giampaolo Manzolini ◽  
Paolo Silva
Keyword(s):  
Solar Energy ◽  
Energy Demand ◽  
Working Fluid ◽  
Fluid Temperature ◽  
Parabolic Trough ◽  
High Solar Radiation ◽  
Power Block ◽  
The Usa ◽  
Solar Field ◽  
Steam Cycle

The role of renewable energies and in particular solar energy could be fundamental in future scenarios of worldwide increase of energy demand: thermodynamic solar energy can play an important role in country with high solar radiation. This paper discusses the development and testing of an innovative code for the prediction of thermodynamic performances at nominal conditions and the estimation of costs of the whole plant, for different parabolic trough solar fields. The code allows a preliminary design of the solar field lay-out, the sizing of the main components of the plant and the optimization of the steam cycle. The code, named PATTO (PArabolic Trough Thermodynamic Optimization), allows to separately calculate the thermal efficiency of (i) parabolic trough systems in commerce as well as (ii) combination of components of various commercial systems, in order to exploit different technology solutions: combination of mirrors, receivers and supports. Using the selected parabolic troughs, the plant configuration is then completed by connecting pipes, heat exchangers, the steam cycle, and storage tanks. The code is also flexible in terms of working fluid, temperature and pressure range. Regarding the power block, a conventional steam cycle with super-heater and re-heater sections and up to seven regenerative bleedings is adopted. It is possible to use also simpler configuration as without re-heater or with less regenerative bleedings. Moreover, thanks to simple or sophisticated economic correlations depending on available data, the code calculates the overall investment cost for the considered solar field and the power block. The code performs steady state analysis at nominal conditions, while future developments are planned regarding part load analysis and transient simulations. The model is tested towards real applications and reference values found in literature; in particular, focusing on SEGS VI plant in the USA. Detailed results showing code potentiality, are presented in terms of solar field and power block energy balances, plant auxiliaries, piping and economic analysis.

Problem about Solar Water Heating System and Residential Building Integrated

2012 ◽  
Vol 193-194 ◽  
pp. 30-33
Author(s):  
Xue Ying Wang ◽  
Dong Xu ◽  
Ya Jun Wu
Keyword(s):  
Solar Energy ◽  
Integrated Design ◽  
Water System ◽  
Residential Building ◽  
Heating System ◽  
Hot Water ◽  
Solar Water Heating ◽  
Drainage Design ◽  
Hot Water Supply ◽  
Solar Water Heating System

This article analyzes the problem in application the solar system was used in residential building, puts forward the requirements to use energy and choose the setting of the solar energy collector from two aspects of building and drainage design respectively. In addition, the article explicates andthe solar energy collector and building integrated design and the development of solar energy collector. At last, the article puts forward some Suggestions on the improvement and development of residential solar hot water system and the design of the hot water supply bath solution of practice to make solar energy and low power assisted by night combining.

scholarly journals Utilisation of bleed steam heat to increase the upper heat source temperature in low-temperature ORC

2011 ◽  
Vol 32 (3) ◽  
pp. 57-70 ◽  
Author(s):  
Dariusz Mikielewicz ◽  
Jarosław Mikielewicz
Keyword(s):  
Power Plant ◽  
Low Temperature ◽  
Heat Source ◽  
Silicone Oil ◽  
Hot Water ◽  
Working Fluid ◽  
Preliminary Heating ◽  
Source Temperature ◽  
Heat Source Temperature ◽  
Steam Heat

Utilisation of bleed steam heat to increase the upper heat source temperature in low-temperature ORC In the paper presented is a novel concept to utilize the heat from the turbine bleed to improve the quality of working fluid vapour in the bottoming organic Rankine cycle (ORC). That is a completely novel solution in the literature, which contributes to the increase of ORC efficiency and the overall efficiency of the combined system of the power plant and ORC plant. Calculations have been accomplished for the case when available is a flow rate of low enthalpy hot water at a temperature of 90 °C, which is used for preliminary heating of the working fluid. That hot water is obtained as a result of conversion of exhaust gases in the power plant to the energy of hot water. Then the working fluid is further heated by the bleed steam to reach 120 °C. Such vapour is subsequently directed to the turbine. In the paper 5 possible working fluids were examined, namely R134a, MM, MDM, toluene and ethanol. Only under conditions of 120 °C/40 °C the silicone oil MM showed the best performance, in all other cases the ethanol proved to be best performing fluid of all. Results are compared with the "stand alone" ORC module showing its superiority.

SUNTRACKER

2015 ◽  
Author(s):  
Jon W. Teets ◽  
J. Michael Teets
Keyword(s):  
High Temperature ◽  
Solar Energy ◽  
Electric Power ◽  
Power Electronics ◽  
Turbine Rotor ◽  
Working Fluid ◽  
Brayton Cycle ◽  
Compressor Impeller ◽  
Temperature Application ◽  
Output Electric Power

A SUNTRACKER (illustrated in figure1), is a Concentrating Solar Power (CSP) unit, in the category of solar dish engines. The novel solar dish engine module (shown in figure 2) is designed to provide 10.1kW electric power (measured at the engine output electric power lugs), from a conversion of 21kW solar energy from the solar dish reflective sun light to the high temperature receiver focal point. Total electric power output from the solar dish engine module is attributed to combined cycles, closed brayton cycle (CBC) and a organic rankine cycle (ORC), both of which are hermetically sealed to atmosphere. The CBC engine receives 21kW solar energy from a solar dish, estimated to have 27 square meters (291 square feet) reflective surface area. However, unlike the photovoltaic (PV) units, the SUNTRACKER will provide increased use of available solar energy from sunlight. Concentrated sunlight from the dish will focus on the CBC engine receiver, which in turn heats the working fluid media to as much as 1600F, pending the ratio of solar dish to receiver areas. A specific gas mixture of xenon/helium, with excellent thermodynamic properties is used for the high temperature application. Turbomachinery in the CBC engine has one moving part / assembly (compressor impeller, alternator rotor and turbine rotor), mounted on compliant foil bearings. Reference figure 4 as an example. The engine operates with a compressor impeller stage pressure ratio 1.6, and is recuperated. Electric power, measured at the CBC engine electric power lugs, is 6.4kW. The CBC engine is not new, (a closed Brayton cycle, sealed to atmosphere) [1], [4], [8], [18], [19]. However, the application to extract thermal energy from the sunlight and provide electric power in commercial and residential use is (patented). In addition, to increase the efficiency of solar energy conversion to electric power, waste heat from the CBC engine provides thermal energy to an ORC engine, to generate an additional electrical output of 3.7kW (measured at the output electric power lugs). With use of an ORC system, the size of the radiator (CBC unit) for heat rejection is reduced significantly. Working fluid HFC-RC245fa [10] was selected for the ORC unit, based on the low temperature application. Also, as with the CBC turbomachinery, the ORC rotor assembly has one moving part, comprised of a pump impeller, alternator rotor and turbine rotor. With the two engines combined, total system thermal efficiency is 48% (10.1kW electric power out / 21kW solar energy in). However, power electronics are needed for conversion of high frequency voltage at the engine output electric power leads to 60/50 Hz power, for customer use. Power electronics losses for this machine, debits the power 0.5 kW. Thus total electric power to the customer, as measured at power electronics output terminals, is 9.6kW. With solar energy, from the reflective sunlight solar dish 21kW and measured output power from the power electronics 9.6kW, the conversion of solar energy to useful electric power an efficiency 46% (i.e. 9.6kW / 21kW). In addition, the design does not require external water / liquid for cooling.

RENEWABLE ENERGY INTEGRATION FOR HOT WATER SUPPLY AND HEATING OF BUILDINGS

2021 ◽  
pp. 3-12
Author(s):  
Yu. Selikhov ◽  
K. Gorbunov ◽  
V. Stasov
Keyword(s):  
Solar Energy ◽  
Heat Production ◽  
Heat Supply ◽  
Alternative Energy ◽  
Fossil Fuel ◽  
Heat Pumps ◽  
Climatic Conditions ◽  
Economic Feasibility ◽  
Hot Water ◽  
The Cost

Solar energy is widely used in solar systems, where economy and ecology are combined. Namely, this represents an important moment in the era of depletion of energy resources. The use of solar energy is a promising economical item for all countries of the world, meeting their interests also in terms of energy independence, thanks to which it is confidently gaining a stable position in the global energy sector. The cost of heat obtained through the use of solar installations largely depends on the radiation and climatic conditions of the area where the solar installation is used. The climatic conditions of our country, especially the south, make it possible to use the energy of the Sun to cover a significant part of the need for heat. A decrease in the reserves of fossil fuel and its rise in price have led to the development of optimal technical solutions, efficiency and economic feasibility of using solar installations. And today this is no longer an idle curiosity, but a conscious desire of homeowners to save not only their financial budget, but also health, which is possible only with the use of alternative energy sources, such as: double-circuit solar installations, geothermal heat pumps (HP), wind power generators. The problem is especially acute in the heat supply of housing and communal services (HCS), where the cost of fuel for heat production is several times higher than the cost of electricity. The main disadvantages of centralized heat supply sources are low energy, economic and environmental efficiency. And high transport tariffs for the delivery of energy carriers and frequent accidents on heating mains exacerbate the negative factors inherent in traditional district heating. One of the most effective energy-saving methods that make it possible to save fossil fuel, reduce environmental pollution, and meet the needs of consumers in process heat is the use of heat pump technologies for heat production.

Modeling and Analysis of Power Conversion System for High Temperature Gas Cooled Reactor With Cogeneration

2008 ◽  
Author(s):  
Ali Afrazeh ◽  
Hiwa Khaledi ◽  
Mohammad Bagher Ghofrani
Keyword(s):  
High Temperature ◽  
Heat Source ◽  
Gas Turbine ◽  
Power Conversion ◽  
Hot Water ◽  
Working Fluid ◽  
Closed Cycle ◽  
Nuclear Heat ◽  
Conversion System ◽  
High Temperature Gas

A gas turbine in combination with a nuclear heat source has been subject of study for some years. This paper describes the advantages of a gas turbine combined with an inherently safe and well-proven nuclear heat source. The design of the power conversion system is based on a regenerative, non-intercooled, closed, direct Brayton cycle with high temperature gas-cooled reactor (HTGR), as heat source and helium gas as the working fluid. The plant produces electricity and hot water for district heating (DH). Variation of specific heat, enthalpy and entropy of working fluid with pressure and temperature are included in this model. Advanced blade cooling technology is used in order to allow for a high turbine inlet temperature. The paper starts with an overview of the main characteristics of the nuclear heat source, Then presents a study to determine the specifications of a closed-cycle gas turbine for the HTGR installation. Attention is given to the way such a closed-cycle gas turbine can be modeled. Subsequently the sensitivity of the efficiency to several design choices is investigated. This model is developed in Fortran.

Sign in / Sign up

Export Citation Format

Share Document